Page 2 - Names of Parts
Names of Parts Table Cover Program Knob Operation Button Drainage hose clip Back plate Packing bolt (3) Washing Allocating box Wash Door Observing Glass Window Drainage hose Earth terminal Power supply cable Back plate screw (3) Caution and Warning symbols For your safety and to prevent damages to t...
Page 3 - Safety; Matters Needing Attention
Safety 1. A separate earthed socket is requiredfor the power supply. After installation ofthe washing machine,the power plugshould be accessible during the normalwash. 3. Fuses in the power circuit should be ratedfor 15A. Refer to a washing machine techni-cian or a Haier designated service point for...
Page 6 - Installation
As shown in figure1 remove all the packing materials (including the foam base). Fig 1 Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during trans-portation The steps below should be followed before using theappliance,1. Remove the rear panel of the...
Page 8 - Control Panel
6 Control Panel Turn the knob at "0", then turn off the power and turn the program knob for setting desired wash program. The program knob will not rotate with the programmed washing process. SOAK PAUSE/START EXTRA RINSE CYCLE CELECTOR NO MAX MAX NORMAL LOW LOW SPIN SPIN NO MAX MAX NORMAL LO...
Page 9 - Operational Functions
7 Operational Functions Extra Rinse Button Soak Button Pause/Start Button Press this button,the washing machine will not drainbefore the final spin-drying cycle.a soaking cycle willbe started,and the inner drum will rotate once every 4minutes(at both directions).If you want to spin the laundry,press...
Page 10 - Program Selection
Program Selection 8 Heavy Prewash Normal Light Delicate Normal Light Delicate Normal Delicate Normal Delicate Silk 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 Very heavy soil Non-fade heavily soiledwoolen fabrics Fading and mediumsoiled woolen fabricsNon-fade heavily soiledsilk fabrics Fading and mediumso...
Page 11 - Preparation
1. Power supply Plug in the power supply120V~/60Hz. 3. Laundry treament 2. Water supply Turn on the tap ensure that the water is clear. Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the waterinlet hose are connected correctly and do not leak...
Page 12 - Washing Methods
1. Laundry loading Evenly load the laundry in thewashing machine and then tightlyclose the door of the washingmachineNote: 1) When first using thewashing machine, let it run un-loaded for one program to pre-v e n t t h e l a u n d r y f r o m b e i n gtainted by oil or dirty water fromthe washing ma...
Page 14 - Other Functions
Other Functions 1. Power-off memory funtion: This machine has a power-off menmory funtion. In case of abrupt power failure or the power must be cut off during a program cycle, the present settings will besaved, and operation will resume when the power is switched on again. 2. Trouble messages: judge...
Page 15 - Maintenance
Insert the bolts. 5. If the machine is to be moved a distance location,replace the vibration mounting locks which were re-moved during installation as shown below. 1. Turn of the water and electricity supply af-ter every wash. Open the door to prevent theformation of moisture and odors. If the wash-...
Page 16 - Trouble shooting
The following circumstances do not constitute problems. Do not contact themaintenance service until the problem has been confirmed. Problem Possible Cause The washing machine fails tooperate Poor connection to power supplyPower failureDoor is not properly closedMachine has not been switched on Washi...
Page 17 - Technical Specification
Model Maximum working current (A) Water pressure (MPa) Washing power (W) Spinning power (W) Spinning speed (r/min) Size (HXDXW) (mm) Weight (kg) HBF1055TVE 120V~/60Hz 13 0.05 P 1 400 1200 15 76 1000 8 5 0 x 5 5 0 x 5 9 5 Item Power supply W ashing program Technical Specification 15
Page 18 - Wiring Circuit; PCB
Wiring Circuit 16 Motor M1 M2 M3 M5 M7 M8 CN2-1 CON8 CON6 CN3-3 CN2-3 CN2-5 CN2-7 CN2-9 CN2-11 CON3 CN3-5 CN3-7 CON2 CON1 PCB N G L FA MRN MRL MRC MR EVF EVP PS EVC 12 13 14 11 P PCB-Printed Circuit Board MR-Door Lock PS-Drain PumpP-Pressure Switch EVP,EVF-Cold water ValveEVC-Hot Water ValveFA-Inter...