Haier GDZ22-2- Manuals

Auto Dry cycle and Timed Dry cycle Load clothes into dryer The appropriate load shall be 1/3 ~ 1/2 of the drum volume. Avoid too much load, for a certain space is needed to allow clothes free rotation for uniform and wrinkle-proof drying.When drying big articles, only 2-3 pieces shall be loaded at a...

Timed Dry cycle 1 8 4 7 2 6 Cycles More Dry Less Dry Dry Cool down Cycle completed Extend tumble Customer On Off Wrinkle Care More Time Less Time Auto Dry Rack dry Timed Dry Time Remaining(Min) Time On(Hour) Delay Start On/Off Power Pause Start Temp Level Dryness Air Only(No Heat) High Medium Low No...

Other Features 2. Press "Timed/Cycles" button and select "Rack Dry" cycle 1. Press "Power On/Off" button to power on After powering on, press "Timed/Cycle" button to select "Rack Dry" program. 3. Press "More Time" And "Less Time" buttons to set...

12 For best dr ying results, cleanthe lint filter before Do not overload the dryer. Balance the dryer load, evenly Throughout the dryer for the best results. Drying time depends on many variables: load size, type of fabric andmoisture in it, heat and moisture in the room, electric voltage, length of...

13 Care and Cleaning Guide Lint filter needs to be cleaned before and after each use for your unit toOperate at optimum efficiency. The filter can be slid out, by pulling onThe tab located on the inside of the dryer door. The filter may beWashed or vacuumed. Remove the excess water from the filter b...

14 Troubleshooting Dryer does not operate: Check if unit is plugged in. The plug may have come loose.Check if the electrical wall socket is the correct voltage. Check if the circuit breaker needs to be reset or if the fuse needs to be replaced.Check if the unit is in Off mode. Press Power On/Off but...

15 INSTALLATION INSTRUCTIONS Select a suitable location for the dryer on a hard even surface away from directsunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc.Any floor unevenness should be corrected with the leveling legs located on the bottom of the dryer. Phillips ...

16 Exhaust System Connections Requirements and Instructions 1. Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up inside system and create a fire hazard and restrict air flow. Restricted airflow will increase dryer times. If your present system is made up of plastic du...

17 Materials Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible metal duct andapproved vent hood which has a swing-out damper cover open when the dryer is inoperation. When the dryer stops, the dampers automatically close to prevent draftsand the entrance of insects and rodents. To avoid...

19 Do Not Install Your Dryer: In an area exposed to dripping water or outside weather conditions. In an area where it will come in contact with curtains, thick carpet, or anything that will obstruct the flow of combustion and ventilation air. On carpet. Floor must be solid with a maximum slope of 1i...

20 Dryer must be exhausted outside (outdoors, not beneath the mobilehome) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. If dryer is exhausted through the floor and area beneath themobil...

21 Electrical Connections Requirements and Instructions 1. This appliance must be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. 2. Do not use an extension cord with this dryer. Some extension cords a...

22 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer in the upper corner. 2. Install a strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time.3. Thread a 30 Amp...

Caution: Label all wires prior to disconnection, when servicing controls.Wiring errors can cause improper operation and be dangerous. Check unit for proper operation after servicing. Warning: Discard or destroy the carton and plastic bags after the dryer is unpacked. Children should not be allowed t...

Auto Dry cycle and Timed Dry cycle Load clothes into dryer The appropriate load shall be 1/3 ~ 1/2 of the drum volume. Avoid too much load, for a certain space is needed to allow clothes free rotation for uniform and wrinkle-proof drying.When drying big articles, only 2-3 pieces shall be loaded at a...

Timed Dry cycle 1 8 4 7 2 6 Cycles More Dry Less Dry Dry Cool down Cycle completed Extend tumble Customer On Off Wrinkle Care More Time Less Time Auto Dry Rack dry Timed Dry Time Remaining(Min) Time On(Hour) Delay Start On/Off Power Pause Start Temp Level Dryness Air Only(No Heat) High Medium Low No...

Other Features 2. Press "Timed/Cycles" button and select "Rack Dry" cycle 1. Press "Power On/Off" button to power on After powering on, press "Timed/Cycle" button to select "Rack Dry" program. 3. Press "More Time" And "Less Time" buttons to set...

12 For best dr ying results, cleanthe lint filter before Do not overload the dryer. Balance the dryer load, evenly Throughout the dryer for the best results. Drying time depends on many variables: load size, type of fabric andmoisture in it, heat and moisture in the room, electric voltage, length of...

13 Care and Cleaning Guide Lint filter needs to be cleaned before and after each use for your unit toOperate at optimum efficiency. The filter can be slid out, by pulling onThe tab located on the inside of the dryer door. The filter may beWashed or vacuumed. Remove the excess water from the filter b...

14 Troubleshooting Dryer does not operate: Check if unit is plugged in. The plug may have come loose.Check if the electrical wall socket is the correct voltage. Check if the circuit breaker needs to be reset or if the fuse needs to be replaced.Check if the unit is in Off mode. Press Power On/Off but...

15 INSTALLATION INSTRUCTIONS Select a suitable location for the dryer on a hard even surface away from directsunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc.Any floor unevenness should be corrected with the leveling legs located on the bottom of the dryer. Phillips ...

16 Exhaust System Connections Requirements and Instructions 1. Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up inside system and create a fire hazard and restrict air flow. Restricted airflow will increase dryer times. If your present system is made up of plastic du...

17 Materials Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible metal duct andapproved vent hood which has a swing-out damper cover open when the dryer is inoperation. When the dryer stops, the dampers automatically close to prevent draftsand the entrance of insects and rodents. To avoid...

19 Do Not Install Your Dryer: In an area exposed to dripping water or outside weather conditions. In an area where it will come in contact with curtains, thick carpet, or anything that will obstruct the flow of combustion and ventilation air. On carpet. Floor must be solid with a maximum slope of 1i...

20 Dryer must be exhausted outside (outdoors, not beneath the mobilehome) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. If dryer is exhausted through the floor and area beneath themobil...

21 Electrical Connections Requirements and Instructions 1. This appliance must be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. 2. Do not use an extension cord with this dryer. Some extension cords a...

22 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer in the upper corner. 2. Install a strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time.3. Thread a 30 Amp...

Caution: Label all wires prior to disconnection, when servicing controls.Wiring errors can cause improper operation and be dangerous. Check unit for proper operation after servicing. Warning: Discard or destroy the carton and plastic bags after the dryer is unpacked. Children should not be allowed t...