Haier CRDE400AW - Manuals

4 INSTALLATION INSTRUCTIONS Phillips head and flathead screwdrivers Channel-lock adjustable pliers 1/2 inch open end wrench Carpenter s level Measuring tape (12ft. Min.) Duct tape Rigid or flexible metal 4 inch (10.2 cm) duct Vent hood 1. Remove all packaging material. This includes the foam base an...

5 Exhaust System Connections Requirements and Instructions 1. Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up inside system and create a fire hazard and restrict air flow. Restricted airexhaustflow will increase dryer times. If your present system is made up of plas...

6 Materials E n g l i s h A l t h o u g h v e r t i c a l o r i e n t a t i o n o f t h e e x h a u s t s y s t e m i s a c c e p t a b l e . C e r t a i ne x t e n u a t i n g c i r c u m s t a n c e s c o u l d a f f e c t t h e p e r f o r m a n c e o f t h e d r y e r :1 . O n l y r i g i d m e ...

7 Do Not Install Your Dryer: In an area exposed to dripping water or outside weather conditions. In an area where it will come in contact with curtains, thick carpet, or anything that will obstruct the flow of combustion and ventilation air. On carpet. Floor must be solid with a maximum slope of 1in...

9 Electrical Connections Requirements and Instructions 1. This appliance must be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for Proper grounding. 2. Do not use an extension cord with this dryer. Some extension cords ar...

10 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer in the upper corner. 2. Install a U.L. approved strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time. 3. ...

Understanding the Control Panel OPERATING INSTRUCTIONS 1 2 8 3 7 6 5 4 9 Power On/Off Button: (1) Start/Pause Button: (2) Press the button once to operate the dryer. Press the button once again to turnthe dryer "OFF". Press this button once to start the dry process. Press this button once ag...

Function Light Indicator: The function "display light" indicates selected feature is "ON" or the cycle is about to begin.During the dry cycle, "flashing light" indicates current running program.Rapidly flashing light indicates that the dryer is not operating properly. 1 5 Gro...

Auto Dry cycle and Timed Dry cycle Load clothes into dryer The appropriate load shall be 1/3 ~ 1/2 of the drum volume. Avoid too much load, for a certain space is needed to allow clothes free rotation for uniform and wrinkle-proof drying.When drying big articles, only 2-3 pieces shall be loaded at a...

Timed Dry cycle 1 7 4 6 2 5 Cycles Dry Cool down Cycle completed Extend tumble Customized On Off Wrinkle Care More Time Less Time Auto Dry Rack dry Timed Dry Time Remaining On/Off Power Pause Start Temp Air Only(No Heat) High Medium Low Normal Heavy Cotton Delicate Bulky Items Louder Softer Signal C...

Other Features 2. Press "Timed/Cycles" button and select "Rack Dry" cycle 1. Press "Power On/Off" button to power on After powering on, press "Timed/Cycle" button to select "Rack Dry" program. 3. Press "More Time" And "Less Time" buttons to set...

22 For best dr ying results, clean the lint filter before Do not overload the dryer. Balance the dryer load, evenly Throughout the dryer for the best results. Drying time depends on many variables: load size, type of fabric andmoisture in it, heat and moisture in the room, electric voltage, length o...

23 Care and Cleaning Guide • Lint filter needs to be cleaned before and after each use for your unit to Operate at optimum efficiency. The filter can be slid out, by pulling onThe tab located on the inside of the dryer door. The filter may beWashed or vacuumed. Remove the excess water from the filte...

24 Troubleshooting Dryer does not operate: Check if unit is plugged in. The plug may have come loose.Check if the electrical wall socket is the correct voltage. Check if the circuit breaker needs to be reset or if the fuse needs to be replaced.Check if the unit is in Off mode. Press Power On/Off but...

Full ONE Year WarrantyFor 12 months from the date of original retailpurchase, Haier will repair or replace any parfree of charge including labor that fails due toa defect in materials or workmanship. Limited Warranty After only year from the original retail pur-chase date Haier shall provide a part ...