Graco Model 237069 - Manuals

Page 2 - Warning Symbol; Caution Symbol; CAUTION; WARNING; EQUIPMENT MISUSE HAZARD; SKIN INJECTION HAZARD

307296 2 Table of Contents Warnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surge Tank Conversion Kits 4 . . . . . . . . . . . . . . . . . . . . . Operation 5 . . . . . . . ...

Page 3 - Installation; Typical Mountings

307296 3 Installation Typical Mountings See Fig. 1 for typical mountings. See page 14 for themounting hole layout. Install the surge tank or filter near the pump outlet.Position the surge tank so the labels face away fromthe pump and so the setscrews, near the top andbottom of the tank, face toward ...

Page 4 - Surge Tank Conversion Kits

307296 4 Surge Tank Conversion Kits Surge Tank Conversion Kits 238634 and237704 Use Conversion Kits 238634 or 237704 to add a surgetank to a pump. Kit 238634 includes surge tank238623 (A) and clamp 238630 (B). Kit 237704 includessurge tank 214624 (A), clamp 238630 (B), and attach-ing hardware (C). C...

Page 5 - Operation

307296 5 Operation Before operating the equipment, be sure the drainvalve is closed. Flush the equipment with a compatible solvent toremove oil used for factory testing and rust prevention. If you notice excessive surging at the spray gun, shutoff the pump, trigger the gun to relieve fluid pressure,...

Page 6 - Service; Service Notes

307296 6 Service Pressure Relief Procedure WARNING SKIN INJECTION HAZARD The system pressure must be manuallyrelieved to prevent the system fromstarting or spraying accidentally. Fluid under high pressure can be injected through theskin and cause serious injury. To reduce the risk ofan injury from i...

Page 7 - Parts

1007 1 3 2 1 2 3 4 5 6 23 24 25 18 192021 22 10 11 14 12 15 12 16 13 17 See Accessories for other available screens. Replace filter support if ridges are worn down. 7 Do not damage PTFE o-ring (7). Lubricate andbend into kidney shape, then push into groove. 1 2 3 4 Lubricate. 4 307296 7 Parts Model ...

Page 13 - Accessories; SURGE TANK CLAMPS; STAINLESS STEEL SCREENS

307296 13 Accessories Use Only Genuine Graco Parts and Accessories SURGE TANK CLAMPS 238630 For surge tanks mounted in the fluid outlet of thedisplacement pump. Install the clamp in the optionaloutlet at the base of the air motor. Requires 100902screw, 100016 lockwasher and 100015 nut. 100016 100015...

Page 14 - Mounting Hole

307296 14 Technical Data Category Data MaximumWorkingPressure Model 237069: 7252 psi (500 bar, 50 MPa) All Other Models: 5000 psi (350 bar, 35 MPa) Weight Model 214623: 30 lb (13 kg) Model 214624: 31.5 lb (14 kg) Model 214724: 13 lb (6 kg) Model 214725: 34 lb (15 kg) Model 214726: 34 lb (15 kg) Mode...

Page 15 - Dimensions

307296 15 Dimensions 1005 1008 A* B C D L F E J G K D H F E L K C A* B * For models 238620 and 238623, add approximately 6 in. (152 mm) to the “A” dimension to account for the drain tube and fitting. J Filters Paint Surge Tanks Mastic Surge Tanks Dimensions 238620 237069 214724 & 289310 214624 &...

Page 16 - The Graco Standard Warranty; Graco Information

307296 16 The Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on thedate of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,...