Graco GC-1402F - Manuals - manualsarea.com

Page 2 - Contents

2 GC-1402E Contents Warnings .......................................................... 3 Important Safety Information ......................... 5 Grounding ........................................................ 6 Set-Up ............................................................... 7 Parts ........

Page 3 - Warnings; Splatter Hazard; WARNING; WARNING

3 GC-1402E Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure- specific risk. Refer back to these warnings. Additional, product-specific w...

Page 4 - Pressurized Aluminum Parts Hazard; Plastic Parts Cleaning Solvent Hazard; Skin Injection Hazard; SKIN INJECTION HAZARD; Pressure Relief Procedure for turning off the unit.

4 GC-1402E WARNING SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the bo...

Page 5 - Important Safety Information; Polyester Resins and Gel-Coats; Isocyanate Conditions

5 GC-1402E Important Safety Information Methyl Ethyl Ketone Peroxide (MEKP) MEKP is among the more hazardous materials found in commercial channels. Proper handling of the “unstable (reactive)” chemicals presents a definite challenge to the plastics industry. The highly reactive property which makes...

Page 6 - Grounding

6 GC-1402E This equipment needs to be grounded. Ground the dispense gun through connection to a GlasCraft approved grounded fluid supply hose. Check your local electrical code and related manuals for detailed grounding instructions of all equipment in the work area. A grounding wire and clamp are pr...

Page 7 - Hose Attachment

7 GC-1402E Hose Attachment 1. Push in and rotate the trigger lock to stop the trigger from being activated. 2. Attach the (black p/n 21694-25) material hose to the material inlet fitting on the back of the gun. 3. Attach the (red) atomize air tubing to the atomize air inlet fitting on the back of th...

Page 8 - Parts

8 GC-1402E Repair Kits Part Number Description 23792-00 GUN AIR KIT 23793-00 GUN SEAL KIT 23732-00 GUN FLUID VALVE KIT Standard Equipment Part Number Description 23750-03 FORMULA X CHOP DISPENSE GUN GC-1402 USER MANUAL Formula X Chop Dispense Gun 23750-03 Parts

Page 9 - Assembly Drawings

9 GC-1402E REVISION C 23750-03 Formula X Chop Dispense Gun Assembly Drawings

Page 12 - Daily Maintenance; Pressure Relief Procedure

12 GC-1402E To relieve fluid and air pressures: 1. Push down Yellow slide valve, P/N 21402-00 to bleed off air to system. 2. Open P/N 21228-00 on catalyst pump to recirculation position. 3. Open P/N 21192-00 on bottom of material pump. 4. Verify the trigger lock is engaged. Daily Maintenance It is r...

Page 13 - Maintenance; Notice

13 GC-1402E Parts Replacement Procedure Formula X Chop Gun Before performing maintenance on the dispense gun, follow Pressure Relief Procedure. Due to the different o-ring materials and lubricants used in the dispense guns, never submerge or soak any dis - pense gun in any type of solvent. Submergin...

Page 15 - Dispense Tip Reference Chart; Part; Accessories

15 GC-1402E Dispense Tip Reference Chart Part Number Orifice 23047-J1 .012 J2 .014 J3 .022 M1 .012 M2 .014 M3 .022 N1 .012 N2 .014 N3 .022 P1 .012 P2 .014 P3 .022 Note: Use p/n: LPA2-120G and p/n: LPA2-121G when using LPA2-147-XXXX and 23047-XX series spray tips. Accessories

Page 16 - Indicates that these tips

16 GC-1402E Dispense Tip Reference Chart Part Number Orifice LPA2-147-1525 0.015 1540 0.015 1550 0.015 1565 0.015 1825 0.018 1840 0.018 1850 0.018 1865 0.018 2125 0.021 2140 0.021 2150 0.021 2165 0.021 2325 0.023 2340 0.023 2350 0.023 2365 0.023 2625 0.026 2640 0.026 2650 0.026 2665 0.026 3125 0.031...

Page 17 - Impingement Dispense Tip Reference Chart

17 GC-1402E Part Number Orifice Min. Width (in.) Max. Width (in.) Min. Output (lbs.) Max Output (lbs.) 23005- C4 0.040 7 16.5 5.4 10.02 C5 0.050 8.5 15.5 6.36 12.23 C6 0.060 7 17 7.31 11.01 C7 0.070 7 13 8.53 10.58 C8 0.080 10 12.5 10.28 13.03 C9 0.090 7.5 10 11.49 12.36 E4 0.040 6 21 4.01 9.16 E5 0...

Page 18 - Technical Data; Category

18 GC-1402E Technical Data Category Data Maximum Fluid Working Pressure 2000 psi (14 MPa, 138 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar) Typical Flow Rate of Pattern Guns Dependent of spray tip Maximum Fluid temperature 100° F (38° C) Trigger Air 1/4in. Tube AAC Air 1/4in. Tube Atomize...

Page 19 - Notes

Page 20 - Graco Ohio Standard Warranty; Graco Ohio Information

Graco Ohio Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited...