Graco GC-1387J - Manuals - manualsarea.com

Page 2 - Contents

2 GC-1387H Contents Warnings .......................................................... 3 Important Safety Information ......................... 5 Grounding ........................................................ 6 Set-Up ............................................................... 7 Parts ........

Page 3 - Warnings; Splatter Hazard; WARNING; WARNING

3 GC-1387H Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure- specific risk. Refer back to these warnings. Additional, product-specific w...

Page 4 - Pressurized Aluminum Parts Hazard; Plastic Parts Cleaning Solvent Hazard; Skin Injection Hazard; SKIN INJECTION HAZARD; Pressure Relief Procedure for turning off the unit.; XXXX

4 GC-1387H WARNING SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the bo...

Page 5 - Important Safety Information; Polyester Resins and Gel-Coats; Isocyanate Conditions

5 GC-1387H Important Safety Information Methyl Ethyl Ketone Peroxide (MEKP) MEKP is among the more hazardous materials found in commercial channels. Proper handling of the “unstable (reactive)” chemicals presents a definite challenge to the plastics industry. The highly reactive property which makes...

Page 7 - Hose Attachment

7 GC-1387H Hose Attachment 1. Push in and rotate the trigger lock to stop the trigger from being activated. 2. Attach the (black p/n 21694-25) material hose to the material inlet fitting on the back of the gun. 3. Attach the (yellow p/n 236) solvent line to the solvent inlet fitting on the back of t...

Page 8 - Overnight Shut Down Procedure

8 GC-1387H Overnight Shut Down Procedure The following steps should be followed for overnight shutdown: 1. The yellow air valve located where the air enters the machine should be pushed to the “OFF” (closed) position. To do this simply push on the lever protruding out the side of the valve. This wil...

Page 9 - Parts

9 GC-1387H Part Number Description 23750-00 Formula Dispense Gun 23005-J5 Standard Spray Tip Repair Kits Part Number Description 23792-00 GUN AIR KIT 23793-00 GUN SEAL KIT 23732-00 GUN FLUID VALVE KIT Parts 23750-00 Formula Dispense Gun

Page 13 - Notes

Page 14 - Daily Maintenance; Pressure Relief Procedure

14 GC-1387H To relieve fluid and air pressures: 1. Push down Yellow slide valve, P/N 21402-00 to bleed off air to system. 2. Open P/N 21228-00 on catalyst pump to recirculation position. 3. Open P/N 21192-00 on bottom of material pump. 4. Verify the Trigger lock is engaged. Daily Maintenance It is r...

Page 15 - Hose Removal; Maintenance; Notice

15 GC-1387H Parts Replacement Procedure Formula Gun Before performing maintenance on the dispense gun, follow Pressure Relief Procedure. Due to the different o-ring materials and lubricants used in the dispense guns, never submerge or soak any dis - pense gun in any type of solvent. Submerging or so...

Page 18 - Dispense Tip Reference Chart; Accessories

18 GC-1387H PART NUMBER ORIFICE Min. Width (in.) Max. Width (in.) Min. Output (lbs.) Max Output (lbs.) 23005- C4 0.040 7 16.5 5.4 10.02 C5 0.050 8.5 15.5 6.36 12.23 C6 0.060 7 17 7.31 11.01 C7 0.070 7 13 8.53 10.58 C8 0.080 10 12.5 10.28 13.03 C9 0.090 7.5 10 11.49 12.36 E4 0.040 6 21 4.01 9.16 E5 0...

Page 21 - Part; Small Diameter Airless Or Non Atomized Material Tip

21 GC-1387H 23760-00 20333-00 LPA 2-147-XXXX OR 23047-XX (See page 19&20) 22274-00 23002-00 Part Number Description 20333-00 GASKET 22274-00 TIP SPACER 23002-00 RETAINING NUT 23047-XX SPRAY TIP 23760-00 GUN FRONT HOUSING Small Diameter Airless Or Non Atomized Material Tip Accessories

Page 25 - High Volume / High Filled Resin

25 GC-1387H Part Number Description 20310-90 3/8” MIXING ELEMENT 23760-01 3/8” FRONT MIXER HOUSING High Volume / High Filled Resin Accessories

Page 26 - Technical Data; Category

26 GC-1387H Technical Data Category Data Maximum Fluid Working Pressure 2000 psi (14 MPa, 138 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar) Typical Flow Rate of Pattern Guns Dependent of spray tip (See page 18) Maximum Fluid temperature 100° F (38° C) Trigger Air 1/4in. Tube Air Inlet Siz...

Page 28 - Graco Ohio Standard Warranty; Graco Ohio Information

Graco Ohio Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited...