Graco 3A0096B- Manuals

Page 2 - Contents; Component Manuals in English

Related Manuals 2 3A0096B Contents Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ink Pump Packages . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . ....

Page 3 - Ink Pump Packages

Ink Pump Packages 3A0096B 3 Ink Pump Packages Check your pump package’s identification plate for the 6-digit part number of your pump package. To order replacement parts, see Parts section starting on page 16. Ink Pump Package Part No. Series Ratio Data Monitoring Power Source Pump Size Maximum Air ...

Page 4 - Warnings; WARNING

Warnings 4 3A0096B Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point symbol aler ts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-s...

Page 7 - Installation; Location

Installation 3A0096B 7 Installation Grounding (All Pumps) The equipment must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for the electrical current due to static build up or in the event of a short circuit. Pump: use the ground wire and clamp supp...

Page 8 - Air Line Accessories

Installation 8 3A0096B Air-Powered Pumps • Reference numbers and letters in parentheses in the text refer to numbers and letters in the illustra-tions. • F IG . 2, page 9, shows a typical installation of an air-powered pump. It is only a guide. Contact your Graco distributor for actual system design...

Page 10 - Hydraulic-Powered Pumps

Installation 10 3A0096B Hydraulic-Powered Pumps • Reference numbers and letters in parentheses in the text refer to numbers and letters in the illustra-tions. • F IG . 3, page 11, shows a typical installation of an hydraulic-powered pump. It is only a guide. Contact your Graco distributor for actual...

Page 12 - Setup; Tighten Clamps; Wet Cup Drain Fitting

Setup 12 3A0096B Setup Tighten Clamps See F IG . 4. Before starting, torque the screws (3) secur- ing the four clamps (4) to 21-25 ft-lb (28-34 N•m). Wet Cup See F IG . 5. Before starting, fill the wet cup (P) 1/3 full with Graco Throat Seal Liquid (TSL) or compatible sol-vent. NOTE: The wet cup has...

Page 14 - Start Up and Adjust Pump

Start Up and Adjust Pump 14 3A0096B Start Up and Adjust Pump Air-Powered Pumps 1. Supply fluid to the pump, per the requirements of your system. 2. Be sure the pump air regulator (H) is closed. 3. Open the bleed-type master air valve (J). 4. Hold a metal part of the valve firmly to the side of a gro...

Page 15 - All Pumps; Shutdown

Shutdown 3A0096B 15 All Pumps If the pump fails to prime properly, open the pump bleed valve (N) slightly. See F IG . 6. Use the bleed hole, on the underside of the valve, as a priming valve until the fluid appears at the hole. Close the plug. NOTE: Always use lowest possible fluid pressure to bleed...

Page 16 - Parts; Air-Powered Ink Packages; Package Selection Chart

Parts 16 3A0096B Parts Air-Powered Ink Packages Package Selection Chart Parts labeled n/a are not available as replacement parts. Obtain locally. Ink Pump Package Part No. Series Check-Mate ® Pump Part No. (Ref. No. 1) Pump Description (see 311238/312375) 258744 A P14LCM N34LN0 NXT Air Motor/L500CM ...

Page 18 - Dimensions

Dimensions 18 3A0096B Dimensions Pump Packages with Viscount Hydraulic Motors Pump Packages with NXT 2200, NXT 3400, or NXT 6500 Air Motors A B ti14639a ti14637a A C C B ti14669a 11 in. (279 mm) 14 in. (356 mm) 17 in. (432 mm) 14 in. (356 mm) Four 9/16 in. (14 mm) mounting holes for 1/2 in. (13 mm) ...

Page 19 - Technical Data; Maximum Fluid Working Pressures

Technical Data 3A0096B 19 Technical Data NOTE: Refer to separate motor manual for sound data and motor mounting hole layout. Maximum Fluid Working Pressures Stroke length Air-powered pumps: 4.75 in. (120.65 mm) Hydraulic-powered pumps: 4.69 in. (119.13 mm) Displacement pump effective area Refer to C...

Page 20 - Graco Standard Warranty

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. This manual contains English. MM 3A0096 Graco Headquarters: Minneapolis International Offices: Bel...