Graco 310566C- Manuals

6 310566 Setup WARNING To reduce the risk of serious injury whenever youare instructed to relieve pressure, always follow the Pressure Relief Procedure on page 10. Site Preparation Fig. 1. Relieve system pressure. For installing any one of the packages listed in this manual, select a sitewith at lea...

8 310566 Setup Connect the Fluid Lines Fig. 1. Connect system fluid supply line to the circula-tion package at fluid supply inlet (A). Close filter ballvalves (E) to isolate the circulation package from themain fluid supply line. Connect circulation package to the system fluid returnline at fluid re...

10 310566 Operation Pressure Relief Procedure WARNING PRESSURIZED EQUIPMENT HAZARD The system pressure must be manually relieved toprevent the system from starting or spraying acci-dentally. To reduce the risk of an injury from acci-dental spray from the gun, splashing fluid, ormoving parts, follow ...

12 310566 Operation Starting and Adjusting the Pump 1. Fig. 4. Open all fluid shutoff valves (5–two) (DD). 2. Open the spray gun at the last gun station andkeep it open while starting the pump. 3. Open the bleed-type master air valves (W, EE). 4. Slowly open air regulator (CC) until the pumpstarts. ...

310566 13 Maintenance Preventive Maintenance Schedule The operating conditions of your particular systemdetermine how often maintenance is required. Estab-lish a preventive maintenance schedule by recordingwhen and what kind of maintenance is needed, andthen determine a regular schedule for checking...

14 310566 Maintenance Air Filter Service 1. Fig. 4. Every day, drain contaminants from thebowl before reaching the baffle level by openingthe drain at the bottom of the bowl (BB). WARNING To reduce the risk of serious injury whenever youare instructed to relieve pressure, always follow the Pressure ...

310566 15 Troubleshooting WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always followthe Pressure Relief Procedure (page 10). For pump service see pump manual. For air motor service see air motor manual. Problem Cause(s) Solution(s) Pump output low on ...

16 310566 Parts Right Hand Mount Model: 96A6293:1 Ratio, President Pump TI0982 11 13 14 14 5 4,3 24 5,4,3 14 19 21,20 12,4,3 22 13 52 35 51 44 2 1 1516 17 23 3,4 14 Ref Ref 5 Detail A Detail A 52 Ref 51 Ref 50 49 48 47 Ref 44 Ref 10,18,28 40 39 41 47 31 25,26,27 32,33,34 30 45 39 14,13 46 7 53

28 310566 Technical Data 3:1 Ratio President Pumps, Models 220561 and 220564 Category Data Maximum Working Pressure 3.4 MPa, 34 bar (500 psi) Air Operating Range 0.1–1.1 MPa, 1.4–11 bar (20–166 psi) Air Consumption See Performance Chart Fluid Flow at 60 cycles per minute 37.1 liter/min (9.8 gpm) Pum...

30 310566 Dimensions TI0982 Mount the circulation package so the top of thebracket is 5 to 6 ft (1.5 to 1.8 m) above the floor. 1 Ensure that there is 5 ft (1.5 m) overhead clearance for wall mounted systems and at least 7 ft (2.1 m) forfloor mounted systems. 2 1 2 Model 96A629 Shown

310566 31 Mounting Hole Layout 1 Check that the wall frame is level before bolting it to the wall. 2 Mount the wall frame so the top edge is 5 to 6 ft (1.5 to 1.8 m) above the floor. 2 28.0 in. (711.2 mm) Wall Frame 618216 1 3/8 in. (8) places 0.5 in. (12.7 mm) 32.0 in. (812.8 mm) 3.0 in. (76.2 mm)

32 310566 Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on thedate of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,Grac...