Graco 309584H- Manuals

Page 2 - WARNINGS; Equipment Misuse Hazard; Electric Shock Hazard

2 309584H WARNINGS Equipment Misuse Hazard Equipment misuse can cause equipment to rupture, malfunction, or star t unexpectedly and cause serious injury. • Before operating this equipment, read all manuals, tags, and labels including material labels and instructions. • Do not expose system to rain. ...

Page 3 - Pressurized Equipment Hazard; Cleaning Solvent Hazard with Plastic Parts; Pressure Relief Procedure

309584H 3 Pressurized Equipment Hazard Fluid from gun, leaks or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure, page 3 when you stop spraying and before cleaning, checking or servicing. • Do not point spray gun at anyone; put hand, ...

Page 4 - Component Identification

Component Identification 4 309584H Component Identification D C B M A K G E F F H J N P ti2441b Identifier Component Description A Air Valve Adjusts air to material mix ratio. B Flow Adjustment Nut Sets needle position. C Trigger Engages material flow. D Trigger Lock Holds trigger open to assist ope...

Page 5 - Basic Operation; Hopper Installation

Basic Operation 309584H 5 Basic Operation Hopper Installation 1. The Hose Plug must be securely fastened to bot-tom of gun when using the Hopper. Gun Plug must be removed from top of gun. . 2. Align notched opening in base of hopper to raised notch on hopper port of gun body. 3. Push hopper down, ov...

Page 6 - Mixing Material

Mixing Material 6 309584H Mixing Material Dry Mix - 40 lb (18 kg) bag. 1. Slowly add one 40 lb. (18 kg) bag of texture mate-rial to 5-6 gallons (18.9-22.7 liters) of clean water as instructed on the bag instructions. 2. Agitate to mix, using a half-inch, variable speed drill with mixing paddle, to a...

Page 7 - Spray Techniques

Spray Techniques 309584H 7 Spray Techniques Recommended Nozzle Selection Chart 1 Control air volume with gun air valve. 2 For more material volume try a larger nozzle. Adjusting the System Sufficient fluid output (volume and pressure) and good atomization is a balance of atomizing air, material thic...

Page 8 - Cleanup

Cleanup 8 309584H Cleanup When you have finished spraying 1. Shut off compressor. Disconnect air line from gun. 2. Drain remaining material into a bucket until most of the texture material is out of hopper. 3. Fill hopper with clean water. Remove nozzle from gun and allow water to flow through and o...

Page 9 - Troubleshooting

Troubleshooting 309584H 9 Troubleshooting Problem Cause Solution Material will not flow from hopper • Material too thick. • Not enough air • Gun adjustment set too low • Nozzle too small • Gun is plugged • Not enough material in hopper. • Thin material • Open gun air valve more • Increase trigger tr...

Page 10 - Parts

Parts 10 309584H Parts Technical Data 5 2b 4 (a-b-c-d) 2a 1 3a 3d 3c 3b 3f 2c 3e 6 9 7 8 11 11 12 10 13 Ref No. Part No. Description Qty . 1 277138 BODY, gun (series C) 1 2 234162 KIT, plugs, includes 2a, 2b and 2c 1 2a PLUG, hose port 2b PLUG, hopper port 2c O-RING 3 234159 KIT, needle repair, incl...

Page 11 - Notes

Page 12 - Graco Standard Warranty

Graco Standard Warranty 12 309584H Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any...