Graco 309410 - Manuals

Graco 309410 – Manual in PDF format online.

Manuals:

Manual

Manual Graco 309410

Summary

Page 2 - MISE EN GARDE; ADVERTENCIA; WARNING

309410 2 Danger d’incendie et d’explosion : les gaz de solvant et de peinture peuvent s’enflammer ou exploser. Pour éviter les risques d’incendie et d’explosion : N’utiliser l’appareil que dans une zone extrêmement bien aérée. Éliminer toute source d’inflammation ; telle que veilleuses, cigarettes e...

Page 4 - Setup; Change Engine to Motor

309410 4 1. Disconnect engine power cord. 2. Release tension bar. Setup 3. Remove engine; tilt and slide back. 4. Install motor; drop in and push forward. Change Engine to Motor Release

Page 6 - Connect appropriate Graco; Remove second gun port cap

309410 6 1. Connect appropriate Graco high-pressure hose to sprayer. Tighten securely. 2. Connect other end of hose to gun. Setup 3. Tighten securely. 4. Remove tip guard. Note: Remove second gun port cap for multiple guns and repeat steps 1 – 4, 7, 8, 10

Page 8 - Startup

309410 8 1. Place suction tube and drain tube in grounded metal pail partially filled withflushing fluid. Attach ground wire to pailand to true earth ground. 2. Turn prime valve down. Turn pressure control to lowest pressure. Startup 3. Set pump switch OFF. PAINT FLUSH

Page 9 - – Digital display is functional after engine starts –

9 309410 Startup a. Move fuel valve to open b. Move choke to closed c. Set throttle to fast d. Set engine switch ON e. Pull starter cord f. After engine starts, move choke to open g. Set throttle to desired setting – Digital display is functional after engine starts – 4. Start engine a. b. c. d. e. ...

Page 11 - Trigger gun again into flushing fluid pail until; SwitchTip and Guard Assembly; Insert seat and OneSeal; SwitchTip

11 309410 9. Place siphon tube in paint pail. 10. Trigger gun again into flushing fluid pail until paint appears. Assemble tip and guard, page 11. SwitchTip and Guard Assembly 1. Engage trigger safety. 2. Insert SwitchTip . Insert seat and OneSeal . 3. Screw assembly onto gun. Hand tighten. FLUSH PA...

Page 13 - Digital Tracking System

13 309410 Digital Tracking System (DTS) 3. Short press DTS button to move to Job Gallons (or Liters x 10). 4. Press and hold to reset to zero, or short press DTS button to move toLifetime Gallons (or Liters x 10). 5. Short press DTS button to move to Auto- Clean Timer operation (Manual 309278). Note...

Page 14 - Pump stops automatically when material pail is empty.; when ON is displayed.; Change Display Units:

309410 14 WatchDog Pump Protection System Pump stops automatically when material pail is empty. 1. Do Startup . 2. Press and hold DTS button, release when ON is displayed. Note: GAL (or LITER) flashes while pump protection system is active. EMPTY displays and the pump stops when pumpprotection syste...

Page 15 - Pressure must be at zero.

15 309410 Secondary Menu – Stored Data and WatchDog Pump Protection Modes 1. Do Startup steps 1. – 3. Pressure must be at zero. 2. Start engine or motor, page 9. Pressure display appears. 3. Simultaneously press DTS button and set pump on/off switch on. Resettable Hour Meter appears. Sprayer model m...

Page 16 - Short press DTS button to move to Lifetime

309410 16 Secondary Menu – Stored Data and WatchDog Pump Protection Modes 4. Press and hold to reset to zero, or 5. Short press DTS button to move to Lifetime Hour Meter. 6. Short press DTS button to move to TOTAL Gallons (all pressures). 7. Press DTS button to move to stored error code. Press and h...

Page 18 - Put trigger safety ON, return SwitchTip

309410 18 heavyedges Spray Test Pattern Clearing Tip Clogs 1. Trigger gun and spray test pattern. Slowly adjust pressure to eliminateheavy edges. Use smaller tip size ifpressure adjustment can not eliminateheavy edges. 2. Hold gun perpendicular, 10–12 in. (25–30 cm) from surface. Spray backand forth...

Page 19 - Cleanup; Turn engine or motor; OFF; Trigger gun to relieve pressure.; AutoClean procedure; or follow conventional; Pressure Relief

19 309410 Cleanup 1. Set pump switch OFF. Turn engine or motor OFF . 2. Turn pressure to lowest setting. Trigger gun to relieve pressure. 3. Turn prime valve down. Perform AutoClean procedure (Manual 309278) or follow conventional flushing procedure that follows: 4. Remove guard and SwitchTip. Press...

Page 22 - Raise siphon tube above flushing fluid; Make sure plastic center tube is tightened

309410 22 Caution: If flushing with water, do not leave water in sprayer. Flush again with mineral spirits, oil or Pump Armor and leave this protective coating in the sprayer to helpprevent freezing or corrosion and increase sprayer life. 13. Raise siphon tube above flushing fluid and run sprayer fo...

Page 23 - DTS Error Codes; Service

23 309410 DTS Error Codes Service 309409 Reference Repair Manual 309409 or 309411 or call your distributor for service

Page 24 - Graco Warranty; Graco Phone Number

309410 24 Graco Warranty Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects inmaterial and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception ofany specia...