Graco 308609P- Manuals

Graco 308609P– User Manual in PDF format online.

Manuals:

User Manual

User Manual Graco 308609P

Summary

Page 2 - Symbols; Warning Symbol; Caution Symbol; CAUTION; WARNING; EQUIPMENT MISUSE HAZARD

2 308609 Symbols Warning Symbol WARNING This symbol alerts you to the possibility of seriousinjury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage toor destruction of equipment if you do not follow theinstructions. WARNING IN...

Page 3 - FIRE AND EXPLOSION HAZARD; MOVING PARTS HAZARD

3 308609 WARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition andresult in a fire or explosion and serious injury. Ground all equipment. Refer to Grounding on page 4. If there is any static sparking or you feel an electric sho...

Page 4 - Installation; Grounding

4 308609 Installation WARNING FIRE AND EXPLOSION HAZARDAlways maintain a minimum of 1 in. clearancebetween rotating agitator parts and containerto prevent sparks from contact. air line lubricator agitator motor air line filter air regulator and gauge mix tank (reference only) Typical Installation NO...

Page 5 - With or Without an Elevator; For in–drum heavy duty back geared agitator

5 308609 Installation With or Without an Elevator 1. Slide the agitator shaft through the large hole inthe center of the drum cover (29). 2. Rotate the agitator so that the air motor is to theleft of the shaft, as shown in Fig. 2, which will alignthe three tapped holes in the bottom of the agitatorw...

Page 6 - Installing the Siphon Kit

6 308609 Installation Installing the Siphon Kit See the Siphon Kit, Model 238250, Parts List on page 15. 1. Remove the top plug (5) and the bottom plug (20). 2. Replace the bottom plug (20) with the plain bearing(53), and tighten the bearing with a wrench. 3. Work the PTFE o-ring (54) onto the sipho...

Page 7 - Air Requirements

7 308609 Installation Return Tube Kit 238884 (Accessory) Return Tube Kit 238884 is available as an accessory.The kit must be ordered separately. Refer to the sheetpacked with the kit for installation instructions. Air Requirements For continuous use, the 3/4 HP (550 W) agitator airmotor typically re...

Page 8 - Notes

Page 9 - Operation; Startup

9 308609 Operation WARNING MOVING PARTS HAZARDTo reduce the risk of serious injury, including cuts, amputation of fingers by the agitator blades, andsplashing in the eyes or on the skin, always shut off the agitator (disconnect the air line from theagitator) before you raise, check, or repair the ag...

Page 10 - Service; Flushing the Air Motor; Lubricating the Air Motor; Additional Air Motor Service

10 308609 Service Flushing the Air Motor WARNING FIRE AND EXPLOSION HAZARDDo not use kerosene or other flammablesolvents to flush the air motor. Flushingwith flammable solvents could cause fire or explosion and result in serious injury or propertydamage. WARNING HAZARDOUS VAPORSHazardous fluids or t...

Page 11 - Cleaning the Agitator Shaft and Seal; Cleaning an Agitator with a Siphon Kit; Servicing the Gear Reducer

11 308609 Service Cleaning the Agitator Shaft and Seal CAUTION Keep the agitator upright. Do not lay it on its side orupside down, or liquid may flow down the shaft andinto the gear reducer area. If any material is on the shaft (6) within 1/2 in. (13 mm)of the housing (13), it must be removed to pre...

Page 12 - Servicing the Gear Reducer, continued; Additional Agitator Service

12 308609 Service Servicing the Gear Reducer, continued Cleaning and Servicing1. Clean any foreign material off of the outside of theupper and lower housings (8 and 13). NOTE: Do not lose the two small thrust balls (4).One is in the upper housing (8), and one is in thelower housing (13). 2. Inspect ...

Page 14 - Parts

14 308609 Parts Heavy-Duty Stainless Steel Agitator, Model 238157 (includes items 1–34) Heavy-Duty Stainless Steel Agitator with Siphon Kit, Model 240209 (includes items 1–4, 6–19, 21–34, 50–54) Siphon Kit, Model 238250 (includes items 50–54) Â 53 50 52 51 54 05736B 05735B DETAIL A 23 (See DETAIL A)...

Page 18 - Non-Siphon Agitator Package, Model 231413

18 308609 Parts Non-Siphon Agitator Package, Model 231413 Siphon Agitator Package, Model 231414 (shown) 100 101 102 107 104 103 106 05771B Ref No. Part No. Description Qty. Ref No. Part No. Description Qty. 100 238157 AGITATOR; see page 14 for parts 1 101 238283 COVER, sst; see manual 308466 1 102 2...

Page 19 - Technical Data

19 308609 Technical Data Maximum air input pressure 100 psi (7 bar) . . . . . . . . . Motor power rating at 1200 rpm (shaft at 50 rpm), using 12 cfm (0.34 m 3 /min) 0.25 hp (186 W) . . . . . . . Maximum recommended shaft rpm 100 . . . . . . . . . . . . . Gear reducer ratio 24:1 Weight 25.8 lb (11.7 ...

Page 20 - Dimensional Drawings

20 308609 Dimensional Drawings Heavy-Duty Stainless Steel Agitator,Model 238157 (shown) 05737 38 in. (965 mm) 10 in. (254 mm) 32 in. (813 mm) Siphon Kit, Model 238250 20 in. (508 mm) 05773 43 in. (1092 mm) 3 in. (76 mm) 1 Height of Model 240209 is thesame as the Siphon Kit (see right). 1

Page 21 - Mounting Hole Layout

21 308609 Mounting Hole Layout 2.0 in. (51 mm) TI0739 1.43 in. (36.3 mm) 1.40 in. (35.6 mm) 1.40 in. (35.6 mm) Three mounting holes, 0.375 in. (9.5 mm) diameter Center Hole, 2.125 in. (54 mm) diameter Counterbore, 2.92 in. (74.2 mm) diameter x0.25 in. (6.4 mm) deep Outline of Gearbox to Hole (Top Vi...

Page 22 - GRACO INC. AND SUBSIDIARIES

22 308609 Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on thedate of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,Grac...