Graco 258865 - Manuals

Graco 258865 – Manual in PDF format online.

Manuals:

Manual

Manual Graco 258865

Summary

Page 2 - Table of Contents; Important User Information; DO NOT RETURN THIS SPRAYER TO THE STORE!

Table of Contents 2 3A0153E Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . 5Common Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pressure Relief ...

Page 3 - Warnings; WARNING

Warnings 3A0153E 3 Warnings The following warnings are for the setup, use, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer bac...

Page 5 - Component Identification; Fb

Component Identification 3A0153E 5 Component Identification *NOTE: Filter assembly is reverse-threaded. Turn left (or counter-clockwise) to tighten, turn right (or clockwise) to loosen. ti15479a D Fa E R K M C Y T S W B D P A Fa Fb G J H N Z L A ProShot Cordless Paint Sprayer B Sprayer Hook C Outlet...

Page 6 - Common Procedures; Pressure Relief Procedure; Trigger Lock

Common Procedures 6 3A0153E Common Procedures Pressure Relief Procedure 1. Engage trigger lock. 2. Put prime/relief valve UP to release pressure. Trigger Lock Spray Tip Position Prime/Relief Valve Position Do not operate or spray near children. Do not aim the sprayer at, or spray any person or anima...

Page 7 - Charging the Battery; Charger Status Indicator Lights

Charging the Battery 3A0153E 7 Charging the Battery Batteries are initially 50% charges to provide optimum battery life and require charging before first use. It takes approximately 45 minutes to charge a dead battery to 80%, at which point it can be used.It will take approxi-mately 75 minutes to fu...

Page 8 - Setup; Suction Tube Selection

Setup 8 3A0153E Setup Suction Tube Selection This sprayer comes with two different suction tubes. Standard Suction Tube (sprays ceilings and walls): When spraying walls, the inlet of the suction tube should be aimed at the front of the material cup. When spraying ceilings, the inlet of the suction t...

Page 9 - Sprayer Setup

Setup 3A0153E 9 Spraying Stains or Clear Coats (Fine-Finish Optimizer) The Fine-Finish Optimizer should be installed and used when spraying thin material such as stain or clear coats. The Fine-Finish Optimizer restricts the material flow resulting in a finer quality finish. Installation 1. Remove ma...

Page 10 - Materials; Starting a New Job (or Refilling the Cup)

Setup 10 3A0153E Materials • When spraying water-based materials, flush the sprayer thoroughly with water. • When spraying non-water-based materials, flush the sprayer thoroughly with mineral spirits or com-patible, oil-based flushing fluid. Starting a New Job (or Refilling the Cup) 1. Engage trigge...

Page 11 - Reversible Tip Selection Chart; Triggering Sprayer

Install Tip/Guard Assembly (if not installed) 3A0153E 11 Install Tip/Guard Assembly(if not installed) Reversible Tip Selection Chart 1. Engage trigger lock and put prime/relief valve UP to release pressure. Then remove Tip/Guard Assembly. 2. Install filter to Spray Tip/Guard Assembly (make sure filt...

Page 13 - Shutdown and Cleaning; Flushing Sprayer

Shutdown and Cleaning 3A0153E 13 Shutdown and Cleaning Flushing Sprayer 1. Engage trigger lock and pull relief valve UP to release pressure. 2. Remove material cup and properly dispose cup liner or excess material. 3. Remove and clean sprayer intake tube and screen with water (or flushing fluid) and...

Page 15 - Cleaning Sprayer Exterior; Storage

Storage 3A0153E 15 Cleaning Sprayer Exterior • Wipe paint off outside of sprayer using a soft cloth moistened with water or flushing fluid. Do NOT submerge the sprayer. Tips • Tips will require replacement depending on abrasiveness of paint. • Do not spray with worn tip. See Troubleshooting , page 2...

Page 16 - Replacement Parts and Kits

Replacement Parts and Kits 16 3A0153E Replacement Parts and Kits 1 8 11 6 5 4 3 7 12 16 ti15497a 2 15 14 17 9 10 18 20 19 21 22 23 24 ti16473c 13a 13 13a 13 Ref. Part Description 1 262367 Sprayer, replacement (no tip, battery, suction tube, or material cup) 2 16D562 Liner, replacement (10 pack) 3 24...

Page 17 - ProShot Repair Kit; Outlet Valve Fitting; Removal

ProShot Repair Kit 3A0153E 17 ProShot Repair Kit Outlet Valve Fitting NOTE: Before doing any repair to pump, perform Flushing Sprayer procedure, page 13. Removal 1. Engage trigger lock and pull relief valve UP to release pressure. 2. Remove battery. 3. Remove pump outlet cap. 4. Use tool (supplied) ...

Page 18 - Alternate Priming Method

Alternate Priming Method 18 3A0153E Alternate Priming Method 1. Engage trigger lock and put prime/relief valve UP to release pressure. 2. Remove material cup and fill with flushing material. 3. With sprayer in prime mode, turn sprayer upside-down, remove strainer and slowly pour flush-ing material i...

Page 19 - Inlet Valve Cleaning

Alternate Priming Method 3A0153E 19 Inlet Valve Cleaning Removal 1. Engage trigger lock and pull relief valve UP to release pressure. 2. Remove material cup and suction tube. 3. Hold sprayer upside-down and use wrench or socket to loosen and remove inlet fitting, inlet valve, and spring. NOTE: Make ...

Page 20 - Problem

Troubleshooting 20 3A0153E Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to an authorized service center. Problem Cause Solution ProShot makes no sound when trigger is pulled Trigger is locked. Disengage trigger lock. See page 6. Status Indicator Light i...

Page 23 - Technical Data

Technical Data 3A0153E 23 Technical Data Sprayer: 258865 258859 Maximum working pressure 2000 psi (137.8 bar, 13.7 MPa) Weight 6.32 lb (2.87 kg) Dimensions: Length 13.25 in. (33.6 cm) Width 5.0 in. (12.7 cm) Height 10.375 in. (26.4 cm) Storage temperature range ◆❖ 32° to 122°F (0° to 50°C) Operating...

Page 24 - Graco Standard Warranty; Graco Information

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 3A0153 Graco Headquarters: Minneapolis Int...