Graco 221313 - Manuals

Installation 313034J 7 Installation Grounding and Electric Requirements Sprayer must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for electrical current due to static build up or in the event of a short circuit. • The 120 Vac sprayers require a 120...

Component Identification 8 313034J Component Identification A Airless spray gun Dispenses fluid. B Power switch Turns sprayer ON and OFF. C Pressure control knob Increases (clockwise) and decreases (counter-clockwise) fluid pressure in pump, hose, and spray gun. C1 Setting Indicator To select functi...

Operation 10 313034J Operation Trigger Lock Always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped. Pressure Relief Procedure Follow this Pressure Relief Procedure whenever you stop spraying and before cleaning, chec...

Setup 313034J 11 Setup 1. Unscrew tip and guard assembly from gun. 2. Uncoil hose and connect one end to gun. Use two wrenches to tighten securely 3. Connect other end of hose to sprayer. If hose is already connected, make sure connections are tight.4. Turn OFF power switch. 5. Turn Pressure Control...

Setup 313034J 13 Some fluids may prime faster if the Power Switch is momentarily turned off so the pump can slow and stop. Repeat several times if necessary. 14. Continue to trigger gun into waste pail until you see only paint coming out of gun. 15. Release trigger. Engage trig- ger lock. 16. Transf...

Setup 14 313034J Adjust Spray Pressure This sprayer is set up for most airless spraying applica-tions. Details on tip selection, tip wear, coat thickness, etc. are provided on page 15. NOTE: Motor only runs when gun is triggered. Sprayer is designed to stop pumping when gun trigger is released.Align...

Setup 313034J 15 Tip Selection Selecting Tip Hole Size Tips come in a variety of hole sizes for spraying a range of fluids. Your sprayer includes an 0.015 in (0.38 mm) tip for use in most spraying applications. Use the follow-ing table to determine the range of recommended tip hole sizes for each fl...

Setup 16 313034J Understanding Tip Number The last three digits of tip number (i.e.: 221413) contain information about hole size and fan width on surface when gun is held 12 in. (30.5 cm) from surface being sprayed. Reversible Tip Selection Chart Example : For an 8 to 10 in. (203 to 254 mm) fan widt...

Getting Started With Basic Techniques 313034J 17 Getting Started With Basic Techniques Use a piece of scrap cardboard to practice these basic spraying techniques before you begin spraying the sur-face. • Hold gun 12 in. (30 cm) from surface and aim straight at surface. Tilting gun to direct spray an...

Shutdown and Cleaning 18 313034J Shutdown and Cleaning Pail Flushing • For short term shutdown periods (overnight to two days) refer to Short Term Storage, page 23. • For flushing after spraying oil-based coatings, use compatible oil-based flushing fluid or mineral spirits. Read Priming and Flushing...

Shutdown and Cleaning 20 313034J Power Flush Power flushing is a faster method of flushing. It can only be used after spraying water-based coatings. 1. Relieve pressure , page 10. 2. Remove tip and guard assembly from gun and place in waste pail. 3. Place empty waste and paint pails side by side. 4....

Shutdown and Cleaning 22 313034J Cleaning InstaClean ™ Fluid Filter (ProLTS Sprayers Only) The InstaClean Fluid Filter prevents particles from entering paint hose. After each use, remove and clean it to insure peak performance. 1. Relieve pressure , page 10. 2. a. Disconnect airless spray hose (a) f...

Storage 313034J 23 Storage Short Term Storage (up to 2 days) 1. Relieve pressure , page 10. 2. Leave suction tube and prime tube in paint pail. 3. Cover paint pail and hoses tightly with plastic wrap. 4. a. Engage trigger lock. b. Leave gun attached to hose. c. If you have not already cleaned them, ...

Storage 24 313034J Stowing Sprayer 1. Screw inlet screen onto suction tube. 2. Coil hose. Leave it con- nected to sprayer. Wrap hose around hose wrap bracket. 3. Secure a plastic bag around suction tube to catch any drips. 4. Store sprayer indoors. NOTICE Before storing sprayer make sure all water i...

Maintenance and Service 313034J 25 Maintenance and Service Caring for Sprayer Keep sprayer and all accessories clean and in good working order. To avoid overheating motor, keep vent holes in shroud clear for air flow. Do not cover sprayer while spraying. Paint Hoses Check hose for damage every time ...

Troubleshooting 26 313034J Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to a Graco/M AGNUM authorized service center. Problem Cause Solution Power switch is on and sprayer is plugged in, but motor does not run, and pump does not cycle. Pressure is set a...

Technical Data 32 313034J Technical Data M AGNUM LTS 15 M AGNUM LTS 17 Working pressure range 0-3000 psi (0-21 MPa, 0-207 bar) 0-3000 psi (0-21 MPa, 0-207 bar) Electric motor 9.0A (open frame, universal) 9.0A (open frame, universal) Operating horsepower 1/2 5/8 Maximum delivery (with tip) 0.27 gpm (...

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 313034 Graco Headquarters: Minneapolis Int...

Component Identification 6 309225W Component Identification A Electric motor (inside enclosures) Provides mechanical power to pump. B Power switch Turns ON and OFF electric motor power (I is ON 0 is OFF). C Pressure control knob Increases (clockwise) and decreases (counter-clockwise) fluid pressure ...

Component Identification 309225W 7 Sprayers Connect cart handle on XR7 and XR9 as fol-lows:1. Position handle on frame and align bolt holes in frame.2. Run bolts through holes with heads pointing toward each other and hand tighten wingnuts.NOTE: For space-saving configuration, loose, (but do not rem...

Operation 8 309225W Operation Pressure Relief Procedure Follow Pressure Relief Procedure when you stop spraying and before cleaning, checking, servicing, or transporting equipment. Read Injection Warning, page 3. 1. Turn power switch (B) OFF and unplug power cord. 2. Turn Spray-Prime/Drain valve (J)...

Setup 309225W 9 Setup 1. Unscrew tip and guard assembly from gun. 2. Uncoil hose and con- nect one end to gun. 3. Connect other end of hose to sprayer. 4. Turn OFF power switch. 5. Turn Pressure Control Knob all the way left (counter-clockwise) to mini-mum pressure. If hose is already connected, mak...

Priming 10 309225W Priming Oil- or Water-based Materials • When spraying with solvents, ground gun. Read Grounding and Electric Require-ments, Maintaining grounding continuity, page 5. • To avoid fluid splashing back on your skin or into your eyes, always aim gun at inside wall of pail. 1. Turn Spra...

Priming 309225W 11 11. Submerge suction tube in paint. 12. Turn power switch ON. 13. When paint starts to come out of prime tube, aim gun toward waste pail, pull and hold gun trigger and turn Spray-Prime/Drain valve to SPRAY. 14. When paint comes out of gun, release trigger. 15. Clip drain tube to s...

Installing Tip and Base 12 309225W Installing Tip and Base 1. Engage trigger lock. 2. Verify tip and guard parts are assembled in order shown. 3. Screw tip and guard assembly on gun. Tighten retaining nut. Unclogging Spray Tip To avoid fluid splashback:• Never pull gun trigger when arrow-shaped hand...

Tip Selection 309225W 13 Tip Selection Selecting Tip Hole Size Tips come in a variety of hole sizes for spray-ing a range of fluids. Your sprayer includes an 0.015 in (0.38 mm) tip for use in most spraying applications. Use the following table to deter-mine the range of recommended tip hole sizes fo...

Tip Selection 14 309225W Reversible Tip Selection Chart Example: For an 8 to 10 in. (203 to 254 mm) fan width and 0.013 (0.33 mm) hole size, order Part No. 221413. Choosing the Correct Tip for the Job Consider coating and surface to be sprayed. Make sure you use best tip hole size for that coating a...

Spraying Techniques 309225W 15 Spraying Techniques This sprayer is set up for most airless spraying applications. Details on tip selection, tip wear, coat thickness, etc. are provided on page 13. Preventing Excessive Tip Wear • Spray should be atomized (evenly distrib-uted, no gaps at edges). Start ...

Shutdown and Cleaning 16 309225W Triggering Gun Pull trigger after starting stroke. Release trig-ger before end of stroke. Gun must be moving when trigger is pulled and released. Aiming Gun Aim tip of gun at bottom edge of previous stroke, overlapping each stroke by half. Shutdown and Cleaning Pail ...

Shutdown and Cleaning 309225W 17 7. Turn power switch ON. 8. Slowly align arrow on sprayer with Pail symbol on Pressure Control knob until pump starts. 9. Flush until approximately 1/3 of the flushing fluid is emptied from the pail. 10. Turn power switch OFF. Turn Spray-Prime/Drain valve to SPRAY. 1...

Shutdown and Cleaning 309225W 19 Cleaning InstaClean ™ Fluid Filter (XR models only) The InstaClean Fluid Filter prevents particles from entering paint hose. After each use, remove and clean it to insure peak perfor-mance. 1. Turn power switch OFF. 2. Disconnect airless spray hose from sprayer and r...

Storage 20 309225W Storage Short Term Storage (up to 2 days) 1. Place suction and drain tube in paint can. 2. Cover can and hoses tightly with plastic wrap. 3. a. Engage trigger lock. b. Leave gun attached to hose. c. Remove tip and guard and clean with water or flushing solvent. A soft brush can be...

Storage 309225W 21 5. Turn pressure control knob clockwise until the pump turns on. 6. When storage fluid comes out of prime tube (5-10 seconds) turn power switch OFF. 7. Turn Spray-Prime/Drain valve to SPRAY to keep storage fluid in sprayer dur-ing storage. Stowing Sprayer 1. Screw inlet screen ont...

Troubleshooting 22 309225W Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to a Graco/Magnum authorized service center. Refer to Component Identification, page 6 for reference letters used in table. Problem Cause Solution Power switch is on and sprayer is ...

Maintenance and Service 26 309225W Maintenance and Service Caring for Sprayer Keep sprayer and all accessories clean and in good working order. To avoid overheating motor, keep vent holes in shroud clear for air flow. Do not cover sprayer while spraying. Paint Hoses Check hose for damage every time ...

Technical Data 309225W 27 Technical Data M AGNUM dx M AGNUM XR5 M AGNUM XR7 M AGNUM XR9 Working pressure range 0-2800 psi (0-19 MPa, 0 -193 bar) 0-3000 psi (0-21 MPa, 0-207 bar) 0-3000 psi (0-21 MPa, 0-207 bar) 0-3000 psi (0-21 MPa, 0-207 bar) Electric motor All 120 Vac: 6.5A Model 247238: 3.5A (ope...

Graco Standard Warranty 28 309225W Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any...