Graco 17F005 - Manuals

General Power Tool Safety Information 3A4702B 5 General Power Tool Safety Information Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The ...

Warnings 3A4702B 7 Warnings The following warnings are for the setup, use, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warn...

Know Your Sprayer 3A4702B 11 Know Your Sprayer A N SPRAY PRIME P J D E L G M K T T F B C ti29712a A Cup Cover B FlexLiner C Cup Support D VacuValve Cap E VacuValve Air Hole F VacuValve Reservoir G Pump Filter J Prime Pump/Spray Knob K Power Cord L Sprayer Trigger M Speed Control, ProControl II N Spr...

Start Up 12 3A4702B Start Up Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. 1. Disconnect power (unplug power cord). 2. Turn Prime Pump/Spray Knob down to PRIME PUMP position to relieve pressure. Starting a New Job If you are using the sprayer for the ve...

Start Up 3A4702B 15 Refilling FlexLiner If sprayer runs out of paint simply separate the cup support from the cup cover/sprayer and refill the FlexLiner.1. Unplug sprayer from power source and open the VacuValve to allow air into the FlexLiner. 2. Separate the cup support from the cup cover/sprayer....

How to Spray 16 3A4702B How to Spray Take a few moments prior to spraying and review these simple tips to ensure your spraying project is a success. NOTE: For proper sprayer operation use only a tip from the same tip family that came with your sprayer. Speed Control The speed control allows for infi...

How to Spray 3A4702B 17 Triggering Sprayer Pull trigger after starting stroke. Release trigger before end of stroke. Sprayer must be moving when trigger is pulled and released. Aiming Sprayer Aim sprayer at bottom edge of previous stroke, overlapping each stroke by half. Rotating the spray tip guard...

How to Spray 18 3A4702B When spraying vertical corners turn spray tip guard to the horizontal orientation and move sprayer up and down. Spray Pattern Quality A good spray pattern is evenly distributed as it hits the surface. • Spray should be atomized (evenly distributed, no gaps at edges). If tails...

Cleanup 20 3A4702B Cleanup Cleaning Sprayer Cleaning your sprayer properly and after every spray job is of the utmost importance! Proper care and maintenance will make your paint sprayer last and work for you trouble free. See Cleaning Fluid Compatibility , page 28.1. Turn Prime Pump/Spray knob to P...

Cleanup 3A4702B 23 16. Use a soft cloth to clean the cup support and cup cover. Cleaning VacuValve The VacuValve is an important part of your sprayer and it should be cleaned after every use.1. Remove VacuValve cap from cup cover and clean it. 2. Clean VacuValve reservoir in lid. 3. Clean VacuValve ...

Storage 24 3A4702B Storage With proper storage, the sprayer will be ready to use the next time it is needed. Pump Armor fluid protects the sprayer while in storage. It helps protect sprayer against freezing and corrosion when not in use.1. Clean the sprayer and cup assembly. See Cleanup , page 20 . ...

Common Procedures 3A4702B 25 Common Procedures Spray Tip Installation To prevent spray tip leaks make certain spray tip and tip guard are installed properly.1. Perform Pressure Relief Procedure , page 12. 2. Use spray tip (A) to insert seal (B) into tip guard (C). 3. Insert Spray Tip. Spray tip must...

Reference 28 3A4702B Reference Spray Tip Selection Spray tips come in a variety of hole sizes for spraying a range of fluids. Your sprayer includes a tip for use in most paint spraying applications. Use the coatings table on page 16 to determine the range of recommended tip hole sizes for each fluid...

Maintenance 3A4702B 29 Maintenance Routine maintenance is important to ensure proper operation of your sprayer. Cleaning Outlet Valves Dirt and debris in the outlet valve assemblies may affect sprayer performance and require cleaning.1. To clean the three outlet valves, remove two pump plugs and fro...

Replacement Parts 30 3A4702B Replacement Parts 37 37a 34 1 31 9 3 11 19 16 15 13 14 18 52 12 ti29777a 30 25 51 29 36 4b 4 4a 50 3 4 7 1 2 Ref. Torque Ref. Torque 10 in-lb (1.1 N•m) 55-65 in-lb (6.2 - 7.3 N•m) 8-10 in-lb (0.9 - 1.1 N•m) 5-7 in-lb (0.6 - 0.8 N•m) 10-15 in-lb (1.1 - 1.7 N•m) 1 4 2 7 3

Replacement Parts 3A4702B 31 Parts List Ref. Sprayer Name Part # Description 1 All 17P185 Kit, pump assembly includes 4, 9, 11, 25 3 All 17P554 Filter. pump, 60 mesh, 3 pack All 17P555 Filter. pump, 100 mesh, 3 pack 4 All 17P183 Kit, outlet valve repair includes 3 of 4a, 2 of 4b, 2 of 50, 1 of 51 4a...

Troubleshooting 3A4702B 35 Spray Pattern Diagnostics Problem Cause Solution Spray pattern is uneven: Operator is moving too fast while spraying. Slow speed of movement. Spray tip is clogged. Unclog spray tip or clean spray tip see Clear Tip Clog , page 18. Material difficult to atomize. Increase spe...

Technical Specifications 3A4702B 37 Technical Specifications HandHeld Sprayer U.S. Metric Max Working Pressure 2000 psi 14 MPa, 138bar Maximum Amperage 2.8 Amps 2.8 Amps Weight 4.6 lb 2.1 kg Dimensions: Length 14.0 in. 36.1 cm Width 5 in. 12.7 cm Height 10.5 in. 26.7 cm Storage Temperature Range  ...

Graco Limited Warranty 38 3A4702B Graco Limited Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any s...

Graco Limited Warranty 3A4702B 39 Graco Information For the latest information about Graco products, visit www.graco.com . For patent information, see www.graco.com/patents . TO PLACE AN ORDER, contact your Graco distributor or call 1-888-541-9788 to identify the nearest distributor.

6 Revolutionize your workday with the Graco Pro Series sprayers. They’re equipped with the breakthrough technology of the ProXChange Pump which allows you to replace your pump on the job faster and easier without any tools, eliminating downtime and keeping you spraying. Get your midsize-to-large job...

7 Full-time painting pros depend on sprayers that stay up and running, day in and day out, while delivering versatility and high-quality application. Graco’s Commercial Series sprayers handle the widest range of interior and exterior jobs. They’re loaded with smart, rugged design features that make ...

8 SG2 ™ Metal Spray Gun – 243011 • In-handle paint filter reduces tip clogs and improves finish • Full trigger (4-finger) is comfortable when spraying for long periods of time • Trigger pull is 30% lighter than competitors for easy operation and less fatigue • Includes 515 Reverse-A-Clean RAC ® IV S...

MAXIMUM TIP SIZE GRACO SPRAYERS MAXIMUM TIP SIZE SUPPORTED Project Painter Plus .015 in Magnum X5 .015 in Magnum X7 .017 in Magnum ProX17 .017 in Magnum ProX19 .019 in Magnum ProX21 .021 in TrueCoat Pro II .017 in Graco Pro210 es .021 in The last two digits are the size of the tip opening in thousan...

GRACO PRODUCT COMPARISON TrueCoat 360 TrueCoat 360 DSP TrueCoat 360 VsP TrueCoat Pro II Magnum Project Painter Plus Magnum X5 Magnum X7 Magnum ProX17 Magnum ProX17 Magnum ProX19 Magnum ProX19 Magnum ProX21 Magnum ProX21 Pro210 es Model Number 16Y385 16Y385 17D889 16N673 257025 262800 262805 17G177 1...

© 2016 Graco Inc. 344066A 10/16 Printed in the U.S.A.Refer to the operating manual for complete details on limited 1 year warranty. Questions? 888- 541-9788 magnum.graco.com/aplus magnum.graco.com Brand Preferred by PROS! MADE IN THE USA WITH GLOBAL COMPONENTS AGAINST MANUFACTURING DEFECTS L I M I T...