Gefen EXT-HDMI-CAT5-145 - Manuals

Page 2 - Technical Support; Fax; Technical Support Hours:; any accompanying doc u men ta tion without prior written notice.; ASKING FOR ASSISTANCE

Technical Support : Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen Inc.c/o Customer Service20600 Nordhoff St Chatsworth, CA 91311 [email protected] Notice Gefen Inc. reserves the right to make ch...

Page 3 - CONTENTS

CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 Connecting And Operating The 1:5 Splitter For HDMI Over CAT-5 9 EDID Modes 10 Equalization & Boost Settings 11 Network Cable Wiring Diagr...

Page 4 - INTRODUCTION

1 Congratulations on your purchase of the 1:5 Splitter For HDMI Over CAT-5. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies. Gefen’...

Page 5 - :5 Splitter For HDMI Over CAT-5 will split the HDMI signal to 5 HDMI; High quality CAT-6 cabling should be used for maximum performance.; OPERATION NOTES

READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1:5 SPLITTER FOR HDMI OVER CAT-5 1:5 Splitter For HDMI Over CAT-5 will split the HDMI signal to 5 HDMI • outputs. 4 of these outputs can be sent over CAT-5, CAT-5e or CAT-6 cables to remote locations while the last output can be used for local use....

Page 6 - Features; HDMI Video Distribution to up to 5 local displays or 4 remote; Package Includes; FEATURES

3 Features HDMI Video Distribution to up to 5 local displays or 4 remote • 300 ft. at 1080i; 150-ft range for 1080p • Maintains high resolution video - beautiful, sharp HDTV resolutions up to • 1080p, 2k, and computer resolutions up to 1920 x 1200 are easily achieved Enables greater versatility when...

Page 7 - SENDER PANEL LAYOUT

4 Front Panel Back Panel 1 2 3 4 5 4 5 4 5 4 5 6 7 8 9 9 9 9 9 SENDER PANEL LAYOUT

Page 8 - SENDER PANEL DESCRIPTIONS

5 Reset Button 1 Pressing this button will reset the unit and cause the source to re-detect the EDID. This is useful for when the EDID mode on the rear panel is changed. Active LED Indicator 2 This LED will become active when a valid link between the 1:5 Splitter For HDMI Over CAT-5 sender and the s...

Page 9 - RECEIVER PANEL LAYOUT

6 Front Panel Back Panel 1 2 3 5 4 6 RECEIVER PANEL LAYOUT

Page 10 - RECEIVER PANEL DESCRIPTIONS

7 Equalization Trim Pot 1 This Trim Pot is used to equalize the incoming HDMI signal to account for variances in CAT cable skew. By default, the Auto EQ feature is enabled and this Trim Pot does not need to be adjusted. In the event that manual EQ mode is enabled, this Trim Pot will be used to equal...

Page 11 - How to Connect the 1:5 Splitter For HDMI Over CAT-5; sender unit using the supplied HDMI cable.; CONNECTING AND OPERATING THE

8 How to Connect the 1:5 Splitter For HDMI Over CAT-5 Connect the HDMI source device to the 1:5 Splitter For HDMI Over CAT-5 1. sender unit using the supplied HDMI cable. Connect up to 4 of the HDMI outputs to the HDMI jumper inputs using the 2. supplied short HDMI jumper cables. The fi fth port can...

Page 12 - How to Change EDID Modes; source device so that it can re-detect the new EDID change.; EDID MODES

9 EDID (Extended Display Identifi cation Data) contains information on the resolution and general capabilities of a display device. This information is used by the source device to output a compatible signal that the display can accept. This information can even be used by some source devices to lim...

Page 13 - EQUALIZATION & BOOST SETTINGS

10 Each 1:5 Splitter For HDMI Over CAT-5 receiver contains a Dip Switch bank located on the underside of the unit. This bank of 4 Dip Switches are covered with a piece of silver metallic tape. These Dip Switches will modify boost settings and change the equalization mode. EQUALIZATION MODES Dip Swit...

Page 14 - Orange; NETWORK CABLE WIRING DIAGRAM

1 2 3 4 5 6 7 8 Gefen has specifi cally engineered their products to work with the TIA/EIA-568-B specifi cation. Please adhere to the table below when fi eld terminating cable for use with Gefen products. Failure to do so may produce unexpected results and reduced performance. CAT-5, CAT-5e, and CAT...

Page 15 - SPECIFICATIONS

12 Video Amplifi er Bandwidth ....................................................................... 165 MHz Input Video Signal .............................................................................. 1.2 Volts p-p Input DDC Signal ................................................................