Gefen EXT-DVIRS232-1FO - Manuals

Page 2 - ASKING FOR ASSISTANCE; Technical Support; Fax; Technical Support Hours:; :00 AM to 5:00 PM Monday thru Friday Pacifi c Time; Notice; any accompanying doc u men ta tion without prior written notice.; Extender for DVI and RS232 Over One Fiber Optic Cable; is a trademark of Gefen, LLC

ASKING FOR ASSISTANCE Technical Support : Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday Pacifi c Time Write To: Gefen, LLCc/o Customer Service20600 Nordhoff St Chatsworth, CA 91311 [email protected] Notice Gefen...

Page 3 - CONTENTS

CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender unit Layout 5 Sender unit Descriptions 6 Receiver unit Layout 7 Receiver unit Descriptions 8 Connecting the Extender for DVI and RS232 Over One Fiber Optic Cable 8 Wiring Diagram 9 DIP Switch Confi guration 9 Sender Unit 11 Receiver Unit ...

Page 4 - INTRODUCTION; Gefen

1 INTRODUCTION Congratulations on your purchase of the Extender for DVI and RS232 Over One Fiber Optic Cable. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution a...

Page 5 - OPERATION NOTES; READ THESE NOTES BEFORE INSTALLING OR

2 OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR DVI AND RS232 OVER ONE FIBER OPTIC CABLE • When HDCP content is passed-through, DVI can only be extended up to1000 feet (300 meters). • RS-232 data is bi-directional for direct commands and echo function or status inf...

Page 6 - FEATURES; Features; Supports HD resolutions up to 1080p Full HD; Package Includes

3 FEATURES Features • Extends DVI up to 1640 feet (500 meters) • Supports HD resolutions up to 1080p Full HD • Supports VESA resolutions up to 1920 x 1200 • RS-232 port for automation • Locking power supplies Package Includes (1) Sender unit (EXT-DVIRS232-1FOS)(1) Receiver unit (EXT-DVIRS232-1FOR)(1...

Page 7 - SENDER UNIT LAYOUT; Front

Page 8 - SENDER UNIT DESCRIPTIONS; In

5 SENDER UNIT DESCRIPTIONS 1 P (Power Indicator) This two-color LED will turn bright red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supplyhas been connected to an available wall outlet. This LED will turn bright greenonce the Sender uni...

Page 9 - RECEIVER UNIT LAYOUT

Page 10 - RECEIVER UNIT DESCRIPTIONS; Out

7 RECEIVER UNIT DESCRIPTIONS 1 RS-232 Connect an RS-232 cable from this port to the RS-232 device. 2 DVI Out Connect a DVI display to this DVI port. Calibration Indicator This LED will alternate from red to green during the calibration procedure. TheLED will turn solid green once the calibration pro...

Page 11 - How to Connect the; CONNECTING THE EXTENDER FOR DVI AND RS232

8 EXT-DVIRS232-1FO RS-232 CABLE DVI CABLE FIBER OPTIC CABLE (Up to 1640 ft) Sender Computer Receiver DVI Display d How to Connect the Extender for DVI and RS232 Over One Fiber Optic Cable 1. Connect the computer (or other DVI source) to the Sender unit using theincluded Locking Dual Link DVI cable. ...

Page 12 - DIP SWITCH CONFIGURATION; DIP Switches

DIP SWITCH CONFIGURATION 9 DIP Switches On the bottom of the Sender unit and Receiver unit are a bank of four (4) DIP switches. These DIP switches provide control over EDID, Deep Color, and unit Calibration. It may be necessary to remove the strip of tape to expose the DIP switches.To change the DIP...

Page 13 - DIP 3 - Calibration Mode; OFF - Enables Calibration Mode

10 DIP SWITCH CONFIGURATION DIP 2 - Deep Color • OFF - Enables Deep Color support (12-bit color) Enables Deep Color support. In Pass-through EDID Mode, setting DIP 2 to the OFF position has no effect since all EDID information is passed through. • ON - Forces 8-bit Color Disables Deep Color in the E...

Page 14 - Receiver unit; Reserved for future expansion.

11 DIP SWITCH CONFIGURATION Receiver unit DIP 1 - Not Used • Reserved for future expansion. DIP 2 - Not Used • Reserved for future expansion. DIP 3 - Calibration Mode • OFF - Enables Calibration Mode Enables Calibration Mode. Make sure to set DIP switch 3 on both theSender unit and Receiver unit whe...

Page 15 - CALIBRATION PROCEDURE; Calibrating the Sender unit and Receiver unit; section at the beginning of this; not

12 CALIBRATION PROCEDURE Calibrating the Sender unit and Receiver unit 1. Make sure DIP switch 3 on both the Sender unit and the Receiver unit are inthe OFF position (see pages 9 and 11). 2. Connect one end of the fi ber cable to the Sender unit. Connect the other end of the fi ber cable to the Rece...

Page 16 - RS-232 SERIAL CONTROL

13 RS-232 SERIAL CONTROL RS232 Settings g Bits per second ............................................................................................ 19200 Data bits ............................................................................................................... 8Parity ................

Page 17 - SPECIFICATIONS

14 SPECIFICATIONS Maximum Pixel Clock................................................................................ 165 MHz Input Video Signal................................................................................ 1.2 Volts p-p Input DDC Signal................................................

Page 18 - WARRANTY; Proof of sale may be required in order to claim warranty.; PRODUCT REGISTRATION; under the Support section of the Gefen Web site.

WARRANTY 15 Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notifi ed within two (2) years from the date of shipment, Gefen will, at its option, repair or replace theequipment, provided that the...

Page 19 - Pb

20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com [email protected] Rev A2 This product uses UL listed power supplies. Pb