Gefen EXT-COMPAUD-CAT5-142 - Manuals

Page 2 - Technical Support; Fax; Technical Support Hours:; any accompanying doc u men ta tion without prior written notice.; :2 Component Audio Over CAT5; is a trademark of Gefen Inc.; ASKING FOR ASSISTANCE

Technical Support : Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen Inc.c/o Customer Service20600 Nordhoff St Chatsworth, CA 91311 [email protected] Notice Gefen Inc. reserves the right to make ch...

Page 3 - CONTENTS

CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 Connecting And Operating The 1:2 Component Audio Over CAT5 9 Adjusting The Video Quality 10 Network Cable Wiring Diagram 11 Specifi cations 1...

Page 4 - INTRODUCTION

1 Congratulations on your purchase of the 1:2 Component Audio Over CAT5. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies. Gefen’s r...

Page 5 - adapters for proper operation.; OPERATION NOTES

READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1:2 COMPONENT AUDIO OVER CAT5 Use only industry standard Category-5 Enhanced (CAT-5e) cable to operate • the 1:2 Component Audio Over CAT5. Cat-6 cables can also be used. Unit will convert digital audio to analog audio and analog audio to digital a...

Page 6 - Features; Supports up to 1080p component video; Package Includes; FEATURES

3 Features Supports up to 1080p component video • Supports analog L+R audio and multichannel digital audio via optical Toslink • or S/PDIF jacks Simple plug-and-play installation • Equalizations for different CAT-5 skews • No loss of quality over long distances • Package Includes (1) Component Audio...

Page 7 - SENDER PANEL LAYOUT

4 Front Panel Back Panel 1 7 4 5 6 2 3 SENDER PANEL LAYOUT

Page 8 - SENDER PANEL DESCRIPTIONS; Connect the component source device to this input.

5 SENDER PANEL DESCRIPTIONS 5V DC Power Input 1 Connect the included 5V DC power supply input this port. Once this has been properly connected the power LED will become active. 3 RCA Component Input 2 Connect the component source device to this input. 2 RCA Analog Stereo Input 3 Connect the source’s...

Page 9 - RECEIVER PANEL LAYOUT

6 Front Panel Back Panel 1 2 3 4 5 6 7 8 9 11 10 12 13 RECEIVER PANEL LAYOUT

Page 10 - RECEIVER PANEL DESCRIPTIONS

7 RECEIVER PANEL DESCRIPTIONS Brightness Trim Pot 1 Use this adjustment Trim Pot to brighten/darken the output video signal. See page 9. Focus Trim Pot 2 Use this adjustment Trim Pot to focus/blur the output video signal. See page 9. Power LED Indicator 3 This LED will become active once the include...

Page 11 - How to Connect the 1:2 Component Audio Over CAT5; CONNECTING AND OPERATING THE 1:2 COMPONENT AUDIO OVER CAT5

8 How to Connect the 1:2 Component Audio Over CAT5 Connect the component video source to the Component Audio Over CAT5 1. sending unit using the supplied 3 RCA component cable. Connect audio to the Component audio Over CAT5 sender unit using either 2. user supplied audio cables or the included audio...

Page 12 - ADJUSTING THE VIDEO QUALITY; Brightness

9 ADJUSTING THE VIDEO QUALITY The 1:2 Component Audio Over CAT5 receiving unit can adjust both the brightness and focus of the reproduced video signal. Differences in cable skew and distance are factors that can affect these settings. To adjust these settings and tune the video signal please use the...

Page 13 - Orange; NETWORK CABLE WIRING DIAGRAM

1 2 3 4 5 6 7 8 Gefen has specifi cally engineered their products to work with the TIA/EIA-568-B specifi cation. Please adhere to the table below when fi eld terminating cable for use with Gefen products. Failure to do so may produce unexpected results and reduced performance. CAT-5, CAT-5e, and CAT...

Page 14 - SPECIFICATIONS

11 Video Amplifi er Bandwidth ....................................................................... 350 MHz Input Video Signal .............................................................................. 1.2 Volts p-p Input Sync Signal ...............................................................