Garland XE24 - Manuals

Garland XE24 – Manual in PDF format online.

Manuals:

Manual

Manual Garland XE24

Summary

Page 2 - INTRODUCTION

Part # 4517125 (09/03) Page 2 INTRODUCTION The Garland Xpress Grill provides a method for eﬃcient two-sided cooking, while accommodating a variety of products. The unit will also serve as a ﬂat grill, and meets all standards for safety, eﬃciency, and cleanliness. Standard Features: • Stainless steel...

Page 3 - TABLE OF CONTENTS; Error Messages

Part # 4517125 (09/03) Page 3 TABLE OF CONTENTS Introduction ...........................................................2 Standard Features: ............................................................2 Dimensions & Speciﬁcations, XE18 .......................4 Dimensions & Speciﬁcations, XE2...

Page 4 - DIMENSIONS AND SPECIFICATIONS, MODEL XE24

Part # 4517125 (09/03) Page 4 DIMENSIONS AND SPECIFICATIONS, MODEL XE24 24" (610mm) GRILL PLATE WIDTH 11-1/2" (292mm) TOP HEATER (2 PLACES) 28-3/16" (716mm) 24-1/8" (614mm) 24" (610mm) GRILL PLATE DEPTH 33-3/4" (858mm) 26-1/8" (663mm) GRILL PLATE HEIGHT RIGHT SIDE VIEW 11...

Page 5 - DIMENSIONS AND SPECIFICATIONS, MODEL XE36

Part # 4517125 (09/03) Page 5 DIMENSIONS AND SPECIFICATIONS, MODEL XE36 FRONT VIEW TOP VIEW 36-5/32" (918mm) 40-3/16" (1021mm) 26-3/16" (665mm) GRILL PLATE HEIGHT 24" (610mm) GRILL PLATE DEPTH 11-1/2" (292mm) TOP HEATER (3 PLACES) 36" (914mm) GRILL PLATE WIDTH 38-1/2" (97...

Page 6 - SAFETY PRECAUTIONS

Part # 4517125 (09/03) Page 6 SAFETY PRECAUTIONS Always follow these safety precautions when operating the Xpress Grill. • THIS GRILL MUST be operated by persons who have been given adequate training. • THIS EQUIPMENT MUST ONLY BE OPER ATED UNDER AN APPROVED HOOD SYSTEM. • DO NOT operate the grill w...

Page 7 - INSTALLATION; National Codes Requirements:

Part # 4517125 (09/03) Page 7 INSTALLATION IMPORTANT: Rating plates for this appliance are located in two places: 1) inside back panel on left side, 2) under front control panel on center. This equipment must be installed by a competent factory trained, certiﬁed, licensed and / or authorized service...

Page 8 - GRILL CONTROLS; Master Power Switch:

Part # 4517125 (09/03) Page 8 GRILL CONTROLS Master Power Switch: Controls power to the grill and must be turned “ON” to start operation. The controller display will be active when the switch is “ON”. Indicator Lights: There are two, (2), indicator lights, indicating the temperature status of each c...

Page 9 - GRILL CONTROLS continued

Part # 4517125 (09/03) Page 9 GRILL CONTROLS continued Power Button: After the main power switch is turned on, this button will put the control into cook mode. If pressed again, the control will go back to displaying “OFF.” Program Button: The primary function is to access Programming and Calibratio...

Page 10 - OPER ATION; Installing Release Material:; A release material sheet must be replaced when:

Part # 4517125 (09/03) Page 10 OPER ATION Installing Release Material: Slide release material rod through hemmed end of the release material sheet. Hook release material rod on brackets located at the rear of the upper plate UPPER PLATEN (side view) RELEASE MATERIAL HOOK RELEASE MATERIAL ROD RELEASE...

Page 11 - NOTE: If the display reads either “TOO COOL”; To Perform an Additional Cook Cycle:; OPER ATION continued

Part # 4517125 (09/03) Page 11 To Cook in Two-Sided Mode: 1. Select a menu item by pressing or until the desired menu item is displayed. Press the Gap Setting Number desired for the selected item, (Gap Buttons 1-5, or hold for 6-10). The display may read either “TOO COOL” or “TOO HOT,” (alternating ...

Page 12 - Enter Standby; To Display the Current Temperatures:

Part # 4517125 (09/03) Page 12 OPER ATION continued buttons at the same time, starting the cooking time countdown. NOTE: If the display reads either “TOO COOL” or “TOO HOT” the controller will not initiate a cooking sequence. 3. Perform the required functions as they are displayed, i.e.; sear, turn....

Page 13 - Cleaning During Operation:

Part # 4517125 (09/03) Page 13 PLATEN SET: This function allows the platen to be moved up or down once it is parallel to the grill surface. Values range from –160 to +160. EXTENDED TIME: This option will add 6, 4 and 2 seconds to the time of the next three cooks respectively if the grill has had no ...

Page 14 - CLEANING AND MAINTENANCE continued; Caution: Do not scrape or otherwise scratch the

Part # 4517125 (09/03) Page 14 CLEANING AND MAINTENANCE continued 7. Remove the release sheet locking clips and bars.8. Scrape only the lower grill surface with a grill scraper, and squeegee any residue into the grease troughs with a grill squeegee. Caution: Do not scrape or otherwise scratch the up...

Page 16 - PROGR AMMING

Part # 4517125 (09/03) Page 16 PROGR AMMING Programming Modes/Menu Sequence:

Page 17 - PROGR AMMING continued

Part # 4517125 (09/03) Page 17 PROGR AMMING continued

Page 18 - To Change the Cook Time of a Product:

Part # 4517125 (09/03) Page 18 PROGR AMMING continued Menu Items... To Change the Cook Time of a Product: 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2. Using the Gap Setting buttons, enter the code, (1251). “ENTER CODE **** ” will be displayed. 3. Press to enter the Pr...

Page 19 - To Change a Product Name:

Part # 4517125 (09/03) Page 19 PROGR AMMING continued 5. Use and to choose the desired Menu Item.6. Press four, (4) times to display “(MENU ITEM) GRILL TEMP X X X” displayed in °F or °C. 7. Use and to change the set temperature to the desired value. 8. Press to save the changes. 9. Press to return t...

Page 20 - To View the Software Number:

Part # 4517125 (09/03) Page 20 To View the Garland Part Number: 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2. Using the Gap Setting buttons, enter the code, (1251). “ENTER CODE **** ” will be displayed. 3. Press to enter the Programming Mode. “PROGR AMMING MODE MENU IT...

Page 21 - System Setup; To Change Gap Setting Display Units:

Part # 4517125 (09/03) Page 21 PROGR AMMING continued System Setup To Change temperature Units, (°F or °C): 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2. Using the Gap Setting buttons, enter the code, (1251). “ENTER CODE **** ” will be displayed. 3. Press to enter the ...

Page 22 - • Temperature is rising through the 350-360°F; To Change Platen Set:

Part # 4517125 (09/03) Page 22 6. Use or to change the Probe Calibration to the correct temperature measured with a pyrometer.* SEE CALIBR ATION REQUIREMENTS 7. Press to save the changes. 8. Press to return to “PROGR AMMING MODE SYSTEM SETUP” 9. Press again to exit. To Change Probe Calibration - Gri...

Page 23 - To Change Control Type:; To Change the Grill Function:

Part # 4517125 (09/03) Page 23 6. Use and to change the Instant on Time to the desired value. 7. Press to save the changes. 8. Press to return to “PROGR AMMING MODE MENU ITEMS” 9. Press again to exit. To Change Control Type: 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2...

Page 24 - To Change the Alarm Mode:; Service Mode; To Change SCK Address:

Part # 4517125 (09/03) Page 24 3. Press to enter the Programming Mode. “PROGR AMMING MODE MENU ITEMS” will be displayed. 4. Press two, (2) times. “PROGR AMMING MODE SYSTEM SETUP” will be displayed. 5. Press eleven, (11) times. “START DELAY YES (or NO)” will be displayed. 6. Use and to turn Start Del...

Page 25 - To Perform Limit Switch Test:; Correct Switch Operation:; Gap Button; To Change Gap Setting:

Part # 4517125 (09/03) Page 25 8. Press to return to “PROGR AMMING MODE SERVICE MODE” 9. Press again to exit. To Perform Limit Switch Test: 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2. Using the Gap Setting buttons, enter the code, (1251). “ENTER CODE **** ” will be d...

Page 26 - CALIBR ATION; peak of 360°F or higher.

Part # 4517125 (09/03) Page 26 CALIBR ATION Bi-Weekly Calibration: Tools: Digital Pyrometer with Surface Probe Warning: PERSONAL INJURY FROM BURNS MAY RESULT WHEN COMING IN CONTACT WITH HOT COOKING SURFACES.NOTE: Calibration of grills is done with release material sheets installed.NOTE: CALIBR ATION...

Page 27 - CALIBR ATION continued

Part # 4517125 (09/03) Page 27 Probe Locations: The grill’s thermocouple probes are located on each section of the lower grill plate in the center of the cooking zone as shown in the diagram below. Each upper platen has one thermocouple probe in the center. CALIBR ATION continued TOP PLATEN (3 PLACE...

Page 28 - TROUBLESHOOTING; CLEAR OBSTRUCTION

Part # 4517125 (09/03) Page 28 TROUBLESHOOTING ERROR MESSAGES: NOTE: WE STRONGLY SUGGEST THAT ANY INSTALLATION, MAINTENANCE AND REPAIRS SHOULD BE PERFORMED BY YOUR LOCAL GARLAND AUTHORIZED SERVICE AGENCY. PROBE ERROR: ...occurs when the probe is open or not connected. The control will turn the heat ...

Page 29 - WIRING DIAGR AMS