Furuno MU-150HD - Manuals

Furuno MU-150HD – Manual in PDF format online.

Manuals:

Manual

Manual Furuno MU-150HD

Summary

Page 2 - IMPORTANT NOTICES; General; How to discard this product; Cd; Pb

i IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international users. • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy ...

Page 3 - ii; SAFETY INSTRUCTIONS; WARNING; Safety Instructions for the Operator; WARNING

ii SAFETY INSTRUCTIONS WARNING Indicates a condition that can cause death or serious injury if not avoided. CAUTION Indicates a condition that can cause minor or moderate injury if not avoided. Warning, Caution Mandatory Action Prohibitive Action Read these safety instructions before you operate the...

Page 4 - iii; Safety Instructions for the Installer; About the TFT LCD

SAFETY INSTRUCTIONS iii WARNING WARNING CAUTION CAUTION MU-150HD Standard Steeringcompass compass Turn off the power at the switchboardbefore beginning the installation. Fire or electrical shock can result if thepower is left on. Do not install the equipment where itmay get wet from rain or water sp...

Page 5 - iv; TABLE OF CONTENTS

iv TABLE OF CONTENTS Note: This manual contains both English and Japanese instructions. The Installation Materials, Outline Drawings, and Interconnection Diagram are located at the back of this manual. FOREWORD ............................................................................................

Page 6 - FOREWORD; A Word to the Owner of the MU-150HD; Features; Program Number

v FOREWORD A Word to the Owner of the MU-150HD FURUNO Electric Company thanks you for purchasing the MU-150HD 15” Marine Display. We are confident you will discover why the FURUNO name has become synonymous with quality and re-liability. For over 60 years FURUNO Electric Company has enjoyed an envia...

Page 7 - SYSTEM CONFIGURATION

vi SYSTEM CONFIGURATION Connectable equipment Note 1: This equipment is used as a display for a Non-SOLAS radar or ECDIS. Note 2: Landscape orientation only. Note 3: When inputting SXGA, a circle may be displayed as an ellipse because the aspect ratio differs. See "DISP MODE*" on page 17. Al...

Page 8 - vii; EQUIPMENT LISTS; Standard supply

vii EQUIPMENT LISTS Standard supply *: See the Installation materials at the back of this manual. Optional supply Name Type Code No. Qty Remarks Display Unit MU-150HD — 1 w/ Hard cover Installation Materials CP26-01300 000-016-267 1 set • CP26-01302* • Flush Mounting Plate Assy. (CP26-01301, Code: 0...

Page 9 - Preparation; CAUTION

1 1. MOUNTING, WIRING 1.1 Preparation Mounting type You can install the display unit as follows. See the outline drawing at the back of this manual for mounting dimensions. • Flush mounting, fixed at rear (standard)• Flush mounting, fixed at front (option)• Flush mounting, fixed at rear, with hood (...

Page 11 - Flush Mounting, Fixed at Rear

1. MOUNTING, WIRING 3 1.2 Flush Mounting, Fixed at Rear This is the standard installation method. 1. Make a cutout in the mounting location with the “Flush mounting template” (included). 2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below. 3. Connect all cables at...

Page 14 - Flush Mounting, Fixed at Front

1. MOUNTING, WIRING 6 1.3 Flush Mounting, Fixed at Front If you do not have the enough space to fix the display unit from the rear, you can fix it from the front with the Flush mount kit OP26-4 (option). Flush Mount Kit OP26-4 (Code: 001-080-850) 1. Make a cutout in the mounting location with the fl...

Page 18 - Desktop Mounting

1. MOUNTING, WIRING 10 7. Press the top of the hood to fit the knobs in the cutouts. 8. Fix the hood assembly with the knobs tightly (4 places). 1.5 Desktop Mounting You can fix the display unit to a desktop, using the bracket assembly OP26-2 (option). Bracket assembly OP26-2 (Code: 000-016-268) Nam...

Page 21 - Flush Mounting a Series Side by Side

1. MOUNTING, WIRING 13 1.6 Flush Mounting a Series Side by Side You can flush mount two display units side by side. 1. Make a cutout in the mounting location as shown below. 2. Follow steps 2 to 5 in section 1.2 to set the two display units in the mounting location.3. Attach the flush mount fixtures...

Page 22 - Wiring; C A U T I O N

1. MOUNTING, WIRING 14 1.7 Wiring Refer to figure below and the interconnection diagram at the back of this manual to connect ca-bles. Connector * 1 : Slide switch • ON (upward): Allow digital signal from external equip- ment to control on/off of the display unit. • OFF (downward): Set this position...

Page 24 - ADJUSTMENTS

16 2. ADJUSTMENTS Adjust the MU-150HD according to the equipment connected. 2.1 RGB/DVI Setting You can adjust the screen from the [RGB], [DVI-D1] and [DVI-D2] ports separately. Turn on ex-ternal equipment and adjust the display unit as follows. 1. Select the signal to adjust at the DISP selection w...

Page 26 - Video Composite Signal Setting

2. ADJUSTMENTS 18 2.2 Video Composite Signal Setting You can adjust the VIDEO1, 2 or 3 signal from the VIDEO1, VIDEO2 and VIDEO3 ports separate-ly. The VIDEO1, 2 or 3 signal is displayed in the PIP window also. 1. Select the signal to adjust at the DISP selection window.2. Press the MENU key to show...

Page 27 - The Menu Window Setting; How to adjust the menu window

2. ADJUSTMENTS 19 2.3 The Menu Window Setting 2.3.1 How to adjust the menu window You can adjust the position and transparency of the menu window on the [OSD] (On Screen Dis-play) menu. 1. Press the MENU key to show the menu. 2. Press the W or X key to select [OSD]. OSD menu 3. Press the S or T key ...

Page 28 - How to change the signal name

2. ADJUSTMENTS 20 2.3.2 How to change the signal name You can change the signal name (“RGB”, “DVI1” or “VIDEO1” etc.) to a name (ex. the equipment name) which is easy to understand. The changed name is shown in the DISP selection window, PIP selection window and the indication shown at the upper rig...

Page 29 - OPERATION; Controls

21 3. OPERATION 3.1 Controls MENU DISP PIP BRILL MENU DISP PIP BRILL Open/Close the menu. Light sensor(According to the ambient light.) - Select the menu and menu items. - Adjust the setting.- Move the PIP window. Select the signal to display. - Power On/Off.*- Display the brilliance adjustment wind...

Page 30 - How to Turn the Power On/Off; Turn on/off the power; Lock the operation; How to Adjust the Display Brilliance

3. OPERATION 22 3.2 How to Turn the Power On/Off This section shows how to turn on/off the display unit and the key lock function. 3.2.1 Turn on/off the power How to turn on/off the power depends on the setting of the slide switch. The slide switch is set when the display unit is installed. See sect...

Page 31 - How to Select the Source for Main Picture; How to Select the Source for the PIP Window

3. OPERATION 23 2. Press the W or X key to adjust the brilliance (available range: 1 to 50). You can also adjust the brilliance by pressing the /BRILL key repeatedly. 3. Press the S or T key to close the window. Note 1: If you turn off the display unit with the minimum brilliance, you may become dif...

Page 32 - SYSTEM Menu; How to set the auto dimmer

3. OPERATION 24 1. When the RGB, DVI1 or DVI2 display appears, press the PIP key. The PIP selection window appears. The signal names are shown as you customized at paragraph 2.3.2 on the window. This window disappears if there is no operation for five sec-onds. PIP selection window (Default setting)...

Page 33 - How to adjust the brilliance from the external equipment; How to clear the memory

3. OPERATION 25 3. Press the S or T key to select [AUTO DIMMER]. 4. Press the W or X key to select the adjustment interval. 5. Press the MENU key to close the menu. 3.6.2 How to adjust the brilliance from the external equipment When FAR-21x7 series is connected to the [DVI-D1] or [DVI-D2] port, you ...

Page 34 - Maintenance; NOTICE

26 4. MAINTENANCE, TROUBLESHOOTING 4.1 Maintenance Routine maintenance Regular maintenance is important for good performance. Check the following on a regular basis to keep the equipment in good condition. • Check that the connectors at the bottom of the display unit are tightly fastened.• Check the...

Page 36 - FURUNO; SPECIFICATIONS OF MARINE DISPLAY

FURUNO MU-150HD SP - 1 E4456S01B SPECIFICATIONS OF MARINE DISPLAY MU-150HD 1 GENERAL 1.1 Display 15-inch color LCD 1.2 Effective area 304 x 228 mm approx. 1.3 Resolution XGA (1024 x 768) 1.4 Brightness 1,000 cd/m 2 typical 1.5 Contrast 600: 1 1.6 View angle 160° typical (left/right and up/down: 80° ...

Page 37 - 工事材料表

CODE NO. 001-080-770-00 TYPE CP26-01302 略　　図 OUTLINE 名　　称 NAME 数量 Q'TY 用途／備考 REMARKS 番号 NO. 型名／規格 DESCRIPTIONS 1/1 -0 INSTALLATION MATERIALS 工事材料表 26AD-X-9402 MU-150HD ﾋｭｰｽﾞﾊﾘﾏｰｸ FUSE LABEL 03-153-1312-0 ROHS 1 100-292-140-10 1 CODE NO. FﾏｳﾝﾄｽﾎﾟﾝｼﾞH15 FLUSH MOUNTING SPONGE H 15 26-005-2123-0 2 100-...