Furuno GP-1670F - Manuals - manualsarea.com

Page 2 - SAFETY INSTRUCTIONS; Mandatory Action; WARNING; CAUTION; WARNING

i SAFETY INSTRUCTIONS The user and installer must read the appropriate safety instructions before attempting to install or operate the equipment. WARNING WARNING Do not open the equipment. The equipment uses high voltage that can cause electrical shock. Refer any repair work to a qualified technicia...

Page 3 - MOUNTING; Mounting of Display Unit; Mounting considerations; Mounting procedure

1-1 1. MOUNTING 1.1 Mounting of Display Unit Mounting considerations The display unit can be installed on a tabletop or flush mounted in a console. Select a suitable mounting location considering the following: • Keep the display unit out of direct sunlight.• The temperature and humidity should be m...

Page 5 - How to Mount a Transducer through the Unit; Transducer mounting location

2-1 2. INSTALLATION OF TRANSDUC-ERS 2.1 How to Mount a Transducer through the Unit Transducer mounting location The thru-hull mount transducer provides the best performance of all, since the trans-ducer protrudes from the hull and the effect of air bubbles and turbulence near the hull skin is reduce...

Page 6 - Transducer mounting locations

2. INSTALLATION OF TRANSDUCERS 2-2 Transducer mounting locations Installation procedure 1. With the boat hauled out of the water, mark the location chosen for mounting the transducer on the bottom of the hull. 2. If the hull is not level within 15° in any direction, fairing blocks made out of teak s...

Page 7 - Transducer preparation; Transom Mount Transducer

2. INSTALLATION OF TRANSDUCERS 2-3 5. Mount the transducer and fairing blocks and tighten the locknut. Be sure that the transducer is properly oriented and its working face is parallel to the waterline. Note: Do not over-stress the stuffing tube and locknut through excessive tightening, since the wo...

Page 8 - Installation procedure; Necessary tools

2. INSTALLATION OF TRANSDUCERS 2-4 Installation procedure A suitable mounting location is at least 50 cm away from the engine and where the water flow is smooth. 1. Drill four pilot holes for self-tapping screw (5x20) in the mounting location.2. Coat the threads of the self-tapping screws (5x14) for...

Page 9 - Remarks on installation

2. INSTALLATION OF TRANSDUCERS 2-5 Remarks on installation Installation procedure If the thickness of the hull varies, then the attenuation of the ultrasound pulse. Select a location where attenuation is the lowest. 1. Select 2-3 locations considering the four points mentioned below. (You will final...

Page 11 - WIRING; Display Unit; Power cable

3-1 3. WIRING 3.1 Display Unit All wiring are terminated at the rear of the display unit. Refer to the interconnection diagram on page S-1. Power cable Connect the power cable to the power connector. Connect the leads to the battery (12 or 24 VDC); white to plus(+) terminal and black to minus(-) ter...

Page 12 - Transducer and sensor; External Equipment; About CAN bus connections

3. WIRING 3-2 3.2 Transducer Connect the transducer cable to the XDR port. Transducer and sensor Use the optional conversion cable (02S4147) to connect the optional speed/tempera-ture sensor and the transducer to the XDR port. Refer to Operator’s Manual in detail. Matching box (option, required for ...

Page 13 - PACKING LIST

NAME OUTLINE Q'TY DESCRIPTION/CODE № ＰＡＣＫＩＮＧ　ＬＩＳＴ 14CW-X-9852 -1 GP-1670F-E 1/1 NAME OUTLINE Q'TY DESCRIPTION/CODE № ユニット UN I T GPSﾌﾟﾛｯﾀ / 魚探 GP S PLO TT ER/ SO UND ER 1 (*) GP -1 67 0F 999-999-194-00 予備品 S PA RE PA RTS ﾋｭｰｽﾞ GL AS S T UB E F US E 1 (*) 03 12 0 03. MX P 999-999-186-00 付属品 A CC...