Furuno FSV-24 - Manuals

v EQUIPMENT LISTS Standard supply Name Type Code No. Q’ty Remarks Monitor Unit FSV-2400 - 1 21” color monitor Control Unit FSV-2401 - 1 w/cable FSV-2402 - For FSV-24 Processor Unit FSV-2402S 1 For FSV-24S Transceiver Unit FSV-241E - 1 Power Supply Unit FSV-242 - 1 FSV-247 - 1200 mm stroke Hull Unit ...

1-1 1. MOUNTING THE EQUIPMENT 1.1 Mounting the Hull Unit Note1) The rise/lower control box of the hull unit contains motion sensor. Therefore, never drop the hull unit. Note2) Take care the handling of the transducer. Do not give a strong shock. 1.1.1 Location of hull unit Decide the location of the...

1-2 600 1000 1300 650 Heater Insulator Maintenance space, example sonar compartment Note: After mounting the equipment, install stays for anti-vibration. See page 1-7.

1-3 1.1.2 Shortening the retraction tank The retraction tank is 1300 mm in length when supplied. Shorten the tank as necessary so that the transducer is placed well below the keel when it is fully lowered. The following table provides guidelines for shortening the tank. Refer also to the retraction ...

1-4 1.1.3 Remarks for installation of retraction tank 1. Make, if possible, the installation location a double bottom structure. 2. Install, if possible, the tank on the keel where the tank can be most firmly fixed. 3. Install the reinforcement ribs as near as possible to the top of the retraction t...

1-5 1.1.4 Installing hull unit on retraction tank After welding the retraction tank and allowing sufficient time for cooling, install the hull unit as follows. 1. Clean the hull unit flange, the O-ring and O-ring groove. Coat them with a slight amount of grease. Place the O-ring in position on the t...

1-6 Hex. Nut Spring Washer Flat Washer Bow Mark Hull Unit Flange O-ring Tank Flange Flat Washer Hex. Bolt Hex. Nut Spring Washer Flat Washer Retraction Tank Hex. Bolt O-ring O-ring Flat Washer Spring Washer Hex. Nut Stern side (seven locations) Bow side (17 locations) Installation of hull unit

1-8 1.2 Mounting the Display Unit The display unit is composed of the processor, monitor and control units. 1.2.1 Processor unit Mounting considerations When selecting a mounting location, keep in mind the following points: • The processor unit must be mounted upright. • Locate the unit out of direc...

1-9 Mounting procedure 1. Unfasten two bolts from the bottom of the front side of the processor unit, and pull the unit toward you to separate the unit from the mounting base. 2. Fasten six bolts (M6x20, supplied as installation material) to install the mounting base. 3. Place the processor unit in ...

1-10 Mounting procedure 1. Drill four holes of 12 mm in diameter in the mounting location, referring to the outline drawing for mounting dimensions. 2. Unfasten two M4X10 screws to dismount the front cover. 3. Unfasten two sets of M10 bolts, plain washers and spring washers to separate the monitor f...

1-11 Attaching the CRT filter 1. Attach two spacer (5x2.5, supplied) with screws (M5x10, supplied) to the location shown below. 2. Screw two hood retainer (supplied) into the filter (supplied). 3. Turn two washers ( Ф 12, supplied) into two hood retainer attached at step 2. 4. Attach the filter to t...

1-13 Passing the cable through the bottom of the control unit For permanent mounting ((2) and (3) above), the control cable can be passed through the bottom of the control unit. Do the steps in below. 1. Unfasten eight screws (M4) to remove the cover from the bottom of the control unit. 2. Unscrew t...

1-14 1.3 Mounting the Transceiver Unit The transceiver unit should be mounted on a mounting base (shipyard supply) whose dimensions are as shown in the outline drawing of the transceiver unit at the back of this manual. The transceiver unit should be reinforced against vibration by stays extending f...

1-15 1.5 Grounding the Equipment The power supply unit, processor unit and hull unit have protective grounding. Ground the units with a ground wire (IV-8SQ, local supply) or copper strap to prevent electrical shock. Ground the monitor unit and transceiver unit with a ground wire (IV-8SQ, local suppl...

1-16 Procedure 1. Clean the hull unit flange, O-ring and O-ring groove. Coat them with a slight amount grease. 2. (1200 mm stroke) Use 24 hex. bolts, 48 hex nuts, flat washers and spring washers to fasten the attachment flange to retraction tank. (1600 mm stroke) 24 bolts have already been fitted. U...

1-17 Hex. Bolt Flat Washer O-ring Spring Washer Flat Washer Hex. Nut Attachment Flange O-ring Hex. Nut Spring Washer Flat Washer Hull Unit Flange Existing Tank *: FSV-244E only Attachment flange for 1600 mm stroke transducer, sectional view

1-18 1.7 Mounting the Cable for Extension Kit (option) For extension of the transducer cable between the hull unit and the transceiver unit, use the extension cable kit (option). The kit is available in 5 and 15 meter lengths. Name: Cable for Extension Kit, Type: FSV-2451, Code No.: 000-067-030 Name...

1-20 Hex. bolt Spring washer Spring washer Flat washer O-ring Flat washer Insulation gasket (2) Insulation gasket Hex. bolt Hex. nut Retraction tank Stern side(Seven locations) Bow side(17 locations) O-ring Hex. bolt Flat washer Flange of the hull unit O-ring Insulation gasket (1) Insulation gasket ...

2-1 1 2 2. WIRING 2.1 How to Use the Crimping Tool, Pin Extractor A special crimping tool is necessary for connection of wires to the contact pins of the 38P connector. The pin extractor removes the contact pin from the connector body. This paragraph describes how to crimp and extract the contact pi...

2-2 2.2 Location of Connectors Monitor (Local supply) CONTROL UNIT FSV-2401 CONTROL UNIT FSV-2401 MONITOR UNIT FSV-2400 PROCESSOR UNIT FSV-2402/2402S POWER SUPLY UNIT FSV-242 TRANSCEIVER UNIT FSV-241E HULL UNIT FSV-243E (1200 mm stroke)/FSV-244E (1600 mm stroke) 10S2074 (10 m) or 10S2075 (30 m) 10S1...

2-3 10S214015m 10S214114.5m 1 16 1 16 0.46m 0.5m 13.3m 0.48m 13.3m Transceiver unit side Hull unit side 10S20788m 0.38m 7.2m 0.28m 0.07m 0.07m Raise/lower control box of the hull unit side Clamp point Clamp point * * * *: Cable length between the transceiver and hull unit.

2-4 2.3 Monitor Unit 2.3.1 Fabrication of monitor cable 10S2074 (10 m)/10S2075 (30 m) 6 3 2 1 4 ARMOR SHIELD 1. GRY (No.1)2. BLK/WHT3. GRY (No.2)4. BLK/RED5. GRY (No.3)6. BLK/GRN7. GRY (No.4)8. BLK/YEL 1, 3, 5. 7, 9: Coaxial cablesOthers: Twisted pair cables 9. GRY (No.5)10. BLK/BLU11. BLK/BRN12. BL...

2-5 Housing Clamp Washer Nut Center Pin Gasket 7.5 Shield 3 Guide Pin A Guide Pin B Guide Pin B(Small) Guide Pin A(Large) Position No. Assembling 38P connector Positioning guide pins Guide pins of the connector identify the mating receptacle. They are; • Guide pin A (Large): 4 • Guide pin B (Small):...

2-6 Assembling D-SUB connector (CN-A302) 1. Remove vinyl sheath of cores by 3 mm. 2. Pass the cores through shrink tubes (local supply). 3. Solder cores to connector pins referring to the schematic diagram at the back of this manual. 4. Assemble the connector. Shrink tube Cable clamp Assembling D-su...

2-7 2.3.3 How to connect cables to the monitor unit Connect the monitor cable and control cable to the monitor (FURUNO-supplied monitor) unit as below. 1. Unfasten four screws (M4x10) at the rear of the monitor to loosen the cable cover. 2. Lift and pull the cable cover to remove it. 3. Unfasten two...

2-8 2.4 Processor Unit Cables (10S2074, 10S1258-1 and control cable) from the various units are connected to the CONE Board (10P6905) via the cable clamp (See page 2-2). CAUTION Divide cables attached to the back of the processor unit between right and left side.And then tie each group with a cable ...

2-9 Fabrication of connector 00-8016-038-313761HV (CN-A101) 320 45 40 Shield AnticorrosiveSheath Armor Vinyl Sheath Core Insulating Tape After exposing cores, wind shield around the armor. Fabrication of connector 00-8016-038-313761HV Guide Pin A Guide Pin B Guide Pin B(Small) Guide Pin A(Large) Pos...

2-11 2.4.5 Optional equipment With connection of navigator and electronic fishing equipment, the function of the FSV-24 is expanded to include true motion presentation, target lock, echo sounder picture, FNZ marker presentation and digital indication of position, water temperature and depth. Use the...

2-13 Synchronizing with echo sounder or other sonar To synchronize the transmission of the FSV-24 with an echo sounder or other type of sonar, make connections as shown below. For current driven KP input Processor unit E/S Sonar EXT-KP EXT-KP-IN-HEXT-KP-IN-C 89 KP signal For voltage driven KP (12 V)...

2-15 2.5.2 Fabrication of power cable type DPYCY-4 (TB-B101) Fabricate the cable DPYCY-4 as below for connection to the power unit. ConductorS = 4 mm ∅ = 2.55 mm 2 Vinylsheath Armor Cable DPYCY-4 140 (Power unit side: 200) 35 30 FV5.5-4 M4 (YEL) x2 Vinyl sheath Armor Anticorrosivesheath Fabrication ...

2-17 2.6 Power Supply Unit Connect the power cable DPYCY-4 or equivalent as below. 0V 100V 0V 100V 110/115V 0V 220V 230V For 100/110/115 VAC For 220/230 VAC Ship's mains Transceiver unit Lay the armor of cable in the clamp. Lay the armor of cable in the clamp. TB-D102 (AC IN) TB-D101 (AC OUT) Power ...

2-18 3. Starting from the right side of the junction box, fix the cables by CSK clamp, pass them through cable clamps and connect XH connectors to the MTC board. CKS clamp Cable clamp Note: Capacitors not present on latest version of MTC board. Junction box, cover removed, front view Transducer cabl...

2-19 2.7.2 Raise/Lower Control Box Connect power cable (3 φ ) and the transceiver unit cable (10S2078) as shown below. TB-C101Connect the power cable TPYCY-4(Japan Industrial Standard) or theequivalent to this board. LED (Red)For detection of phase reversal on3 phase power cable CN-C101Connect the t...

2-20 100 25 20 FV5.5-4 M4(yellow) x 3 Sheath Armor(Clamp here by cable clamp.) Vinyl sheath Power cable fabrication

3-1 3. ADJUSTMENT AND CHECK 3.1 Hull Unit Check Note: Before conducting this check (at the dry dock) transmission must be stopped. Default setting of TX transmission is OFF. Confirm as follows. 1. Turn on the power, and then press the [MENU] key to show the main menu. MENU QUIT H-SCAN SETTING... V-S...

3-3 How to check the hull unit 1. Press the POWER ( | ) switch on the control unit (for the display unit) to turn on the equipment. Confirm that the lamps above the ON and switches light. Transducer switches 2. Confirm that the 5V and UP lamps on the raise/lower control box are lit. 3. Remove the co...

3-4 8. Check that LEDs on the panel of the raise/lower control box light as follows: a) UP, MD and DN LEDs light when corresponding limit switch is kicked. b) UP and DOWN LEDs light while UP and DOWN switches are pressed and extinguish when switches are released. 9. Set the TEST/NORMAL switch to NOR...

3-5 SYSTEM MENU QUIT INTERFACE SETTING.. EXT DATA SETTING.. OWN SHIP MARK.. TEST&INITIALIZATION.. TRX SETTING 1.. TRX SETTING 2.. OTHERS.. SYSTEM menu 4. Use the trackball to select OTHERS and press the [MENU] key. 5. Select HEADING ADJUST and press the [MENU] key. OTHERS LANGUAGE ES2 SELECT : E...

3-6 3.3 Configuring Own Ship Mark Set own ship’s dimensions and the location of the transducer to accurately display the own ship mark on the display. 1. Press the [MENU] key to display the SYSTEM menu. SYSTEM MENU QUIT INTERFACE SETTING.. EXT DATA SETTING.. OWN SHIP MARK.. TEST&INITIALIZATION.....

3-7 5. Select ! or " and then press the [MENU] key several times to set the ship’s length (15 to 150 m). 6. Select QUIT to finish the setting. 7. Set the SHIP’S WIDTH (5 to 30 m), TD POSITION 1 (5 to 50 m) or TD POSITION 2 (-10.0 to 10.0 m) similarly. TD POSITION 1: Set the transducer’s distance...

3-8 3.4 Other SYSTEM Menu Items This section shows you how to set up external equipment. Default settings are underlined. 3.4.1 INTERFACE SETTING menu INTERFACE SETTING CIF BAUD RATE : 4800 bps MENU QUIT QUIT AUX BAUD RATE : 19200 bps NMEA 2 BAUD RATE: 4800 bps NMEA 1 BAUD RATE: 4800 bps EXT KP INPU...

3-9 3.4.2 EXT DATA SETTING menu EXT DATA SETTING LOG PULSE : 200p/NM MENU QUIT QUIT SPEED&COURSE : NMEA HEADING : AD10S DATE&TIME : CIF SPEED SENSOR : GPS/DR LAT/LON : NMEA POSITIONING SENSOR : AUTO SEL. WATER DEPTH : NMEA WATER TEMP. : NMEA WATER CURRENT : CIF WIND : CIF EXT DATA SETTING me...

3-10 WATER DEPTH Select the input port for the depth data. (NONE, CIF, NMEA) WATER TEMP. Select the input port for the water temperature data. (NONE, CIF, NMEA) WATER CURRENT Select the input port for the water current data. (NONE, CIF, NMEA) WIND Select the format for the wind data. (NONE, CIF, NME...

3-11 LANGUAGE Select the language. (JAPANESE, ENGLISH) HEADING ADJUST See “3.2 Heading Adjustment”. ES2 SELECT Select the equipment connected to the ES2 port among echosounder and net recorder. (ES, NET REC) ES DRAFT OFFSET When connecting echosounder, set the ship’s draft line to use depth from dra...

3-12 3.5 CONE Board Setting in the Processor Unit Adjust the potentiometers on the CONE Board in the processor unit, referring to the table shown below. Location No. Name Resistance value Function Adjustment R118 ALARM 10 k Ω Adjusting the volume of audio alarm. CW: Large CCW: Small R119 ES2_OFF 1 k...

3-13 3.6 DIP Switch Setting Processor unit, inside view 3.6.1 CIF2/NMEA2 connector interface selection The signal format of the CIF2/NMEA2 port at the back of the processor unit can be set for CIF or NMEA by DIP switch S2-8 on the IFES Board (10P6903). The default format is OFF (CIF). DIP switch set...

3-14 3.6.2 Selecting the Net Sonde information The net depth information from the Net Sonde can be entered from the FNZ port or CIF port. Depending on the input port, select the DIP switch setting as follows. The default setting is FNZ. Input port DIP switch S3 - #1 FNZ(default) OFF CIF1 or NMEA2/CI...

3-15 3.7 Testing TX/RX independently at hull unit To check the Tx/Rx function of the hull unit independently, follow the steps below. Note: This test should not be done at the dry dock. The transducer will be damaged. 1. Turn ON DIP switch S3#1 on the TRCPU Board (10P6926) in the transceiver unit. 2...

4-2 2. Remove two upset screws, detach the plugs J503, J502, J501, J504, J506 and J507, thus pull out the power block. IFES SCAN SCAN2 DU AL DCON Power Block VH4P VH5P Upset screws M5x25 SUS 2 pcs. Protection sheet Power supply pcb Spacer Detach J503, J502, J501, J504 and J506. Detach J507. Hole Pin...

4-3 7. Connect between the processor unit and CS-120A as follows. CS-120A J201 Processor Unit YEL BRN BRNBRN POWER FOR CS-120A port CIF1 or NMEA2/CIF2 port L E PP 123 NNMMJJKKBBEEDDZ 123410 24V0VGND TD-HTD-CRD-HRD-CGNDDSR-CDSR-HDTR-H +24V_H+24V_CGND CIF_TXD_HCIF_TXD_CCIF_RXD_HCIF_RXD_CSHIELD 37-core...

AP-1 Check List Ship Name Date / / Location SCANNING SONAR TYPE FSV-24 RESULT Monitor unit (FSV-2400) Options Control unit (FSV-2401) CS-120A Processor unit (FSV-2402) VI-1100A Transceiver unit (FSV-241E) CS-170 Power supply unit (FSV-242) FSV-2451(5m),FSV2452(15m) Hull unit (FSV-243E/244E ) S/N Ref...

AP-3 DATA SHEET 2 DISPALY UNIT (FSV-2400 ) Check item Contents Check point CK Standard Result Judge Check software version on the each board Self-check display DCON 1050714*** DUAL 1050703*** IFES 1050711*** KEY 1050685*** TRCPU 1050717*** Software version TRX 1050665*** to 1050684*** WC TRANSCEIVER...

AP-4 DATA SHEET 3 User menu H-scan setting P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 Range Gain Tilt T ｘ interval Pulse length Tx output TVG near TVG middle TVG far NL AGC 2AGC Echo average IR Color Color curve Write by color response curve sheet. Display gain Delete color Far TVG curve Beamwidth-H V-scan sett...

CODE NO. 006‑921‑230‑00 TYPE CP10‑04501 略  図 OUTLINE 名  称  NAME 数量 Q'TY 用途／備考 REMARKS 番 号  NO.  型名／規格 DESCRIPTIONS 1/1 ‑6  INSTALLATION MATERIALS 工事材料表 10CO‑X‑9401 ｺﾈｸﾀ(8016） CONNECTOR(8016) 008016‑038‑313761HVF 1 表示部用            FOR MONITOR UNIT 000‑159‑017‑10 1 CODE NO. ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN...

CODE NO. 006‑922‑390‑00 TYPE FP10‑02201 略  図 OUTLINE 名  称  NAME 数量 Q'TY 用途／備考 REMARKS 番 号  NO.  型名／規格 DESCRIPTIONS 1/1 ‑2  ACCESSORIES 付属品表 10CO‑X‑9501 KB直付け金具 KB FIXNG PLATE 03‑144‑1691‑1 1 操作部用          FOR CONTROLL UNIT 100‑263‑941‑00 1 CODE NO. ﾀﾞｽﾄｶﾊﾞｰKB DUST COVER KB 03‑144‑1693‑0 1 操作部用      ...

D C B A 6 5 4 3 2 1 FURUNO ELECTRIC CO., LTD. kg DRAWN CHECKED APPROVED SCALE MASS DWG No. TITLE NAME 名称 INTERCONNECTION DIAGRAM COLOR SCANNING SONAR 相互結線図 注記 ＊２）コネクタは工場にて取付済み。＊３）オプション。＊４）コネクタクランプでアースに落とす。＊５）電源に応じてタップを切り替える。＊６）00‑8016‑038‑313761HV NOTE *2: CONNECTOR PLAGS FITTED AT FACTORY.*3: OPTIO...