Furuno FM-8800D/8800S - Manuals

Page 3 - SAFETY INSTRUCTIONS; WARNING

i SAFETY INSTRUCTIONS WARNING Hazardous voltage. Can shock, burn or causeserious injury. Do not work inside the equip-ment unless totally familiarwith electrical circuits. Turn off the power at the mains switch-board before beginning the installation.Post a warning sign near the switch-board to indi...

Page 4 - ii; TABLE OF CONTENTS

ii TABLE OF CONTENTS SYSTEM CONFIGURATION ................................................................................ iii EQUIPMENT LISTS ........................................................................................... iv 1. MOUNTING .....................................................

Page 5 - iii; SYSTEM CONFIGURATION; Transceiver Unit

iii SYSTEM CONFIGURATION Transceiver Unit FM-8800DFM-8800S HandsetHS-2003 VHFAntenna CH 70 RX Antenna AC/DCPower SupplyUnitPR-240-CE 100-115/200-230 VAC50/60 Hz, 1 φ Category of units Antenna All other units Exposed to weather Protected from weather Category Radio Battery24 VDC 24 VDC JunctionBox*IF...

Page 6 - iv; EQUIPMENT LISTS; Standard Supply; Transceiver; Junction Box; Spare; Standard Supply for VHF Console; Console

iv EQUIPMENT LISTS Standard Supply Name Type Qty Code No. Remarks FM-8800D-E-A FM-8800D-E-NFM-8800D-F-A FM-8800D-F-N FM-8800S-E-A FM-8800S-E-N FM-8800S-F-A FM-8800S-F-N FM-8800S-R-A 1 Transceiver Unit FM-8800S-R-N 1 — D: Duplex S: Simplex E: W ith handset HS-2003 F: W ith microphone DM-2003-F A: W i...

Page 7 - Optional Equipment; Name Type

EQUIPMENT LISTS v Optional Equipment Name Type Code No. Remarks Flush Mount Kit OP05-102 000-054-120 Junction Box IF-8810 — W/ Screw 5x20 4 pcs. DMC Interface IF-8820 — No use for Russian version RB-8800-15 (W/ 1.5 m Cable) RB-8800-20 (W/ 2 m Cable) — ·FP05-05701*, ·Handset HS-8800, ·Hanger W/DIST. ...

Page 8 - vi; Name

EQUIPMENT LISTS vi Name Type Code No. Remarks AP05-01100 000-054-224 Whip antenna 150M-W2VN, Coax. Cable 5D-2V 10m, Connector M-P-5 2 PCS AP05-01200 000-054-232 Whip antenna FAB-151D, Mounting plate 4-310071, Coax. Cable 5D-2V 10m, Connector M-P-5 & M-P-7 Antenna Material AP05-01210 000-054-233 ...

Page 9 - General mounting considerations

1-1 1. MOUNTING Transceiver Unit General mounting considerations Determine the mounting location for the transceiver unit considering operator convenience, proximity to the power source and the ground location. Keep these and the following points in mind when selecting a mounting location. • Locate ...

Page 10 - Overhead; Overview of mounting methods

1. MOUNTING 1-2 Overview of mounting methods Overhead Flush Mount Tabletop Bulkhead Keep pressed for 4 s in case of DISTRESS. The alert is transmitted with steady lighting. PQRS GHI IntCom * 7 4 1 WXYZ MNO PRINT DW # 0 HI/L0 TUV JKL ACK SCAN 8 5 9 6 ENT FILE MENU DEF ABC 2 3 CH16 DISTRESS MSG CALL S...

Page 11 - Mounting procedure for tabletop, overhead and bulkhead mounting; Screw the knob bolts with washers into the transceiver unit.

1. MOUNTING 1-3 Mounting procedure for tabletop, overhead and bulkhead mounting 1. Using the hanger as a template, mark fixing holes in the mounting location. 2. Fix the hanger to the mounting location with self-tapping screws and washers (supplied). (For added support, use nuts, bolts and washers i...

Page 12 - Mounting procedure for flush mount (option); Mounting dimensions for flush mount; VHF Antenna; The antenna requirements

1. MOUNTING 1-4 Mounting procedure for flush mount (option) Requires optional flush mount kit OP05-102 (Code No. 000-054-120). Prepare a cutout in the mounting location whose dimensions are as shown in the figure below. Flush mount kit OP05-102 Name Type Code No. Qty 1 Mounting plate 05-093-1211 100...

Page 13 - Mounting considerations

1. MOUNTING 1-5 CH70 RX Antenna The antenna should be well separated from nearby antennas, masts, and other interfering objects. The mounting procedure is the same as that for the VHF antenna, however consult appropriate outline drawing for details. Handset Hanger The handset hanger can be mounted a...

Page 14 - Mounting of Printer PP-510

1. MOUNTING 1-6 Printer (option) Printer PP-510 To mount the printer, refer to the printer outline drawing at the back of this manual. 1. Select a flat surface. 2. Fix the mounting base to the mounting location with four screws (supplied). 3. Lay the printer on the top of the mounting base and faste...

Page 16 - Up to four remote stations can be connected in a daisy chain.

1. MOUNTING 1-8 Remote station RB-8800/RB-8810 (option) Up to four remote stations can be connected in a daisy chain. Note: For the remote station RB-8800, there are two method of cable entry: bottom-side entry and rear-side entry. For rear-side entry, make one or two holes of more than 12 mm diamet...

Page 17 - Outdoor mounting of RB-8810; entrance with silicone sealant; Note: Confirm that plastic washers are; in screw holes before fixing cover.

1. MOUNTING 1-9 Outdoor mounting of RB-8810 Remote station RB-8810 with waterproof-type handset HS-8800-W-35 can be mounted outdoors. The hanger should be coated as directed below with silicone sealant for waterproofness. 1. Fix the mounting base with self-tapping screws. Coat exposed part of these ...

Page 18 - VHF console; Select a location where controls can be easily operated.; Fixing; wall), referring to the outline drawing at the back of this manual.

1. MOUNTING 1-10 VHF console Install the rack console where the equipment can be easily operated, checked and serviced. Consult with shipyard personnel and ship's officer-in-charge to determine best location. The location must satisfy the following points: • Select a location where controls can be e...

Page 19 - Overview; Connection of Power Supply; Convention vessels, 100/220 VAC ship’s mains; and when AC input fails DC power is activated.

2-1 2. CONNECTIONS Overview The figure below shows where to connect various equipment at the rear of the transceiver unit. EXT SPConnects externalloudspeaker. ANTConnects antenna. CH70 RX ANTConnects DSC antenna here. 24VDCConnects power cable. PRINTERConnects printerPP-510. Ground terminal. IEC6116...

Page 20 - Connection of VHF Antenna; Screw the plug assembly on the cable.

2. CONNECTIONS 2-2 Connection of VHF Antenna The VHF antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type 5D-2V. Be sure to leave some slack in the cable for future service and maintenance. Lay the coaxial cable and attach an M-type plug to the cable (if necessary) as follo...

Page 21 - connection of other cables, see the interconnection diagram.

2. CONNECTIONS 2-3 Connection of DSC Antenna The DSC antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type 5D-2V. Attach an M-type plug to the cable (if necessary) as shown an page 2-2. Screw the plug into the CH70 RX ANT connector at the rear of the transceiver unit. Connec...

Page 23 - White

2. CONNECTIONS 2-5 Connection of AC/DC Power Supply Unit PR-240-CE The power supply PR-240-CE is shipped ready for connection to a 200-230 VAC ship’s mains. If the ship’s mains is 100 VAC – 115 VAC, change the tap connection and terminal board connection as below. Attach label supplied as accessorie...

Page 24 - Protective earth; CAUTION; GND terminal

2. CONNECTIONS 2-6 Protective earth Connect IV-2.0sq wire between ship’s superstructure and the ground terminal on the PR-240-CE. Attach protective earth securely to the ship's body. The protective earth (grounding) is required for the AC/DC power supply unit to prevent electrical shock. CAUTION GND...

Page 25 - Jumper Setting for Termination; DMC interface is not used for Russian version.

2. CONNECTIONS 2-7 Jumper Setting for Termination Note: DMC interface is not used for Russian version. It is necessary, for termination, to change the jumper setting for remote station or DMC interface. Open the unit(s) terminated and change the jumper plugs J2 and J3 to ON position (#2-#3). (Defaul...

Page 26 - Remove four screws

2. CONNECTIONS 2-8 TB1 05P0778 RS-485 TERMINATION J4 ON Remove four screws to open the unit. Set jumper plug to ON (#1-2). DMC Interface IF-8820

Page 27 - Wire connection of VHF console; Connect cables from external equipments to the junction box.

2. CONNECTIONS 2-9 2.10 Wire connection of VHF console 1. Remove the cover assembly and printer assembly (or concealing lid) form the console. For the printer assembly, remove the cables connected at the Transceiver Unit and the terminal board. Cover assembly Binding screw F M4X10 4 places Console T...

Page 28 - This page is intentionally left blank.

2. CONNECTIONS 2-10 This page is intentionally left blank.

Page 29 - ASSEMBLING CONSOLE KIT; VHF console kit; Type Code; Assembling the Console Kit; to the terminal board.

3-1 3. ASSEMBLING CONSOLE KIT A VHF console kit is required to mount the Transceiver Unit in the field. There are two types as shown below. VHF console kit Type Code No. Remarks RC-8800-N-75BG 000-054-125 Without printer RC-8800-A-75BG 000-054-126 With printer Assembling the Console Kit 1. Remove th...

Page 31 - with the console kit.; and then mount the junction box on the console.

3-3 6. Replace the cable attached to junction box with the cable (55 cm, 37-pin D sub) supplied with the console kit. 2 3 J1 J2 J3 A A Replace the original cable with the cable assemblyDSUB37M-PHX3-L550. Junction box(without cover) View Crimp-on lug PH Connector 14P PH Connector 12P PH Connector 10P...

Page 32 - concealing lid to the console.

3-4 Grommets 2 places Junction box 8. For the console w/printer, connect the printer cable for data transmission to the PRINTER port of the Transceiver Unit and fix the power cable to the terminal board as before. Then, fix the printer assembly to the console. For no printer, fasten the concealing l...

Page 35 - PACKING LIST

NAME OUTLINE Q'TY DESCRIPTION/CODE № ＰＡＣＫＩＮＧＬＩＳＴ 05EC‑X‑9858 ‑2 FM‑8800S‑F‑N/ FM‑8800D‑F‑N 1/ 1 NAME OUTLINE Q'TY DESCRIPTION/CODE № ユニット UNIT 送受信機 TR AN S CE IV E R UN I T FM‑8800S/D 000‑054‑225 1 ** 予備品 SPARE PARTS 予備品 SP AR E P AR T S SP05‑05501 005‑377‑820 1 付属品 ACCESSORIES F P 05‑0 57 10 ﾏｲｸ...

Page 38 - 工事材料表

CODE NO. 005‑377‑800 TYPE CP05-09901 略図 OUTLINE 名称 NAME 数量 Q'TY 用途／備考 REMARKS 番号 NO. 型名／規格 DESCRIPTIONS 1/1 ‑2 INSTALLATION MATERIALS 工事材料表 05EC‑X‑9401 ﾐﾆﾋﾟﾝ組品(1) CABLE ASSY. L‑420 1 000‑151‑748 1 CODE NO. ｺﾈｸﾀﾌｰﾄﾞ(XM2) HOUSING CASE XM2S‑3712 1 000‑145‑423 2 CODE NO. ｺﾈｸﾀ(XM2) CONNECTOR XM2...

Page 40 - 付属品表

CODE NO. 005‑951‑920 TYPE FP05‑05511 略図 OUTLINE 名称 NAME 数量 Q'TY 用途／備考 REMARKS 番号 NO. 型名／規格 DESCRIPTIONS 1/1 ‑0 ACCESSORIES 付属品表 05DZ‑X‑9502 +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ SELF‑TAPPING SCREW 4X16 SUS304 1ｼｭ 2 000‑802‑080 1 CODE NO. ﾎﾟﾘｶﾜｯｼｬｰ WASHER M4 2 000‑864‑937 2 CODE NO. （略図の寸法は、参考値です。 DIMENSIONS IN DRAW...

Page 67 - VHF RADIOTELEPHONE

MASS kg NAME 名称 TITLE INTERCONNECTION DIAGRAM 相互結線図国際VHF無線電話装置 DWG No. SCALE DRAWN APPROVED CHECKED D C B A 2 3 4 5 6 1 FURUNO ELECTRIC CO., LTD. FM-8800D/S 123456 ANT M-P-5 7 1 8 2 9 10 CH70 RX ANT M-P-5 12 HANDSET S.GND 1 PTT SW_N 2 MIC(H) 3 MIC(C) 4 HS SP(H) 5 HOOK SW_N 67 F.GND 8 SPKR SP(H) 1 S...

Page 68 - RACK CONSOLE

1 5 4 3 2 A B C D INTERCONNECTION DIAGRAM 相互結線図 FURUNO ELECTRIC CO., LTD. 6 CHECKED APPROVED DRAWN SCALE DWG No. TITLE 名称 NAME kg MASS 国際VHF無線電話装置（ラック組込） VHF RADIOTELEPHONE (RACK CONSOLE) RC-8800 (FM-8800) P P T/R用アンテナANTENNA FOR T/R *2 *2 CH70 WR用アンテナ ANTENNA FOR CH70 WR HANDSETHS-2003 ハンドセット EXT. ...