Furuno FCV-295 - Manuals

Furuno FCV-295 – Manual in PDF format online.

Manuals:

Manual

Manual Furuno FCV-295

Summary

Page 2 - CAUTION; Mandatory Action; SAFETY INSTRUCTIONS; WARNING

i WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. Warning, Caution Mandatory Action Prohibitive Action SAFETY INSTRUC...

Page 3 - ii

ii CAUTION Observe the following compass safedistances to prevent interference to amagnetic compass: Ground the equipment toprevent mutual interference. Do not allow warm water or any otherliquid other than seawater or freshwater to contact the transducer. The transducer may become damaged. Do not t...

Page 4 - iii; SYSTEM CONFIGURATION; Transducer

iii SYSTEM CONFIGURATION Basic configuration is shown with solid line. High Freq. Low Freq. Transducer Transducer Navigator Display unitCV-295 12-24 VDC Rectifier PR-62 100/110/115/220/230 VAC1 㱢 , 50/60 Hz Water temperature sensor T-02MSB, etc. Speed/temp sensor ST-02MSB, etc.

Page 5 - iv; EQUIPMENT LISTS; Standard supply

iv EQUIPMENT LISTS Standard supply Option Name Type Code No. Qty Remarks Display Unit CV-295 - 1 Spare Parts SP02-05501 001-032-740 1 set See packing list at back of this manual. Accessories FP02-05700 000-011-976 1 set Installation Materials CP02-08401 001-032-750 1 set Name Type Code No. Remarks T...

Page 6 - Combination of transducer, thru-hull pipe and tank

v Combination of transducer, thru-hull pipe and tank Output (W) Frequency (kHz) Ship type Transducer Thru-hull pipe Tank 1k/1k 28/50 Steel 28F-850B-9B TWB-6000(2) T-656 FRP - - 28/88 Steel 28F-888B-8 TWB-6000(2) T-657 FRP - - 50/88 Steel 50B-9B88B-8 TWB-6000(2) T-658 FRP - - 50/200 Steel 50/200-1T50...

Page 8 - vii

vii 3k/3k 38/150 Steel 38BL-15HR150B-12H TFB-7000(2) T-683 FRP TRB-1100(2) T-683-F 38/200 Steel 38BL-15HR200B-12H TFB-7000(2) T-683 FRP TRB-1100(2) T-683-F 50/88 Steel 50BL-24H88F-126H TFB-7000(2) T-697 FRP TRB-1100(2) T-697-F Steel 50BL-24HR88F-126H TFB-7000(2) T-682 FRP TRB-1100(2) T-682-F Steel 5...

Page 9 - viii

viii 2k 38 Steel 38BL-9HR TFB-5000(1) T-702 FRP TRB-1000(1) T-702-F 50 Steel 50B-12 TFB-5000(1) T-611 FRP TRB-1000(1) T-611-F Steel 50BL-12 TFB-5000(1) T-702 FRP TRB-1000(1) T-702-F Steel 50BL-12HR TFB-5000(1) T-702 FRP TRB-1000(1) T-702-F 82 Steel 82B-35R TFB-5000(1) T-609 FRP TRB-1000(1) T-609-F 8...

Page 10 - Display Unit; Mounting considerations; NOTICE

1 1. MOUNTING 1.1 Display Unit Mounting considerations • Locate the unit out of direct sunlight.• Select a location where the display screen can be easily observed while operating the control panel. • Leave sufficient space around the unit for maintenance and servicing. Recommended mainte- nance spa...

Page 11 - Transom mount water temperature sensor T-02MTB

2 1.2 Transducer The performance of the echo sounder depends upon the transducer position. A place least affect-ed by air bubbles should be selected since turbulence blocks the sounding path. Further, select a place least influenced by engine noise. It is known that air bubbles are fewest at the pla...

Page 13 - Locknut

4 Through-hull mount water temperature/speed sensor ST-02MSB, ST02-PSB Select a suitable mounting location considering the following: • Select a mid-boat flat position. The sensor does not have to be installed perfectly perpendicu- lar. The sensor must not be located where it might get damaged in dr...

Page 14 - Interconnection

5 2. WIRING 2.1 Interconnection Refer to the interconnection diagram at the back of this manual for detailed information. Wiring diagram for FCV- 295 Low Transducer Speed/Water temperaturesensor Navigator 12-24 VDC DPYCY -1.5 DPYCY -1.5 Rectifier PR-62 100/110/115/220/230 VAC1 φ , 50/60 Hz * Transdu...

Page 15 - Cable Fabrication; Power cable

6 2.2 Cable Fabrication Power cable This echo sounder is designed to be powered with 12-24 VDC. Use the cable DPYCY-1.5 (Japan Industry Standard) or equivalent. Transducer cable Separate the transducer cable well away from power cables to prevent interference. Connect the cable to the transducer por...

Page 17 - Input/Output Sentences; Input sentences

8 2.3 Input/Output Sentences Input sentences Output sentences Sentence Data Remarks BWC Range/bearing to waypoint GGA Time, position GPS position GLC GRI, Time difference Loran C GLL Latitude and longitude GPS position GNS GNSS position fixing GTD Time difference Loran C HDG Ship's heading, deviatio...

Page 18 - Language Setting

9 3. INITIAL SETTING This chapter provides the information necessary for initial setup of the equipment. First turn on the power and set display language. Then, set transducer used, by model number (FURUNO trans-ducer only) or by specifications. 3.1 Language Setting 1. Press [ /BRILL ] key to turn o...

Page 19 - Transducer Data; Entering transducer data by transducer model

10 4. Press T or S to select necessary unit and then press the ENTER key to set. • Depth: m, ft, fa, pb, HR (Japanese unit)• Temp: ° C, ° F • Speed: kt, km/h, mph• Wind: kt, km/h, mph, m/h• Distance: nm, km, sm 5. Press the MENU key. The following message appears. 6. Press any key. The transducer se...

Page 21 - Tap setting

12 6. Press T to select "Transducer" and then press the ENTER key. The list of programmed trans- ducers appears. 7. Press T to S select transducer connected and then press the ENTER key. 8. Jot down the alphabet which appears on the "Tap" line. You may need to change the tap set- tin...

Page 22 - Entering transducer data by transducer specifications; Speed/Water Temperature Sensor Calibration

13 Entering transducer data by transducer specifications To connect the transducers which are not programmed, do as follows: Note: The transducers of 53 - 65 kHz, 111 to 139 kHz and 171 - 183 kHz cannot be connected to the FCV-295 because of noise. 1. At the XDCR Setting dialog box, select "XDCR...

Page 24 - NMEA Port Setting; Description for each item of the NMEA menu

15 3.4 NMEA Port Setting If a GPS navigator and/or other sensor are connected, set up as follows. 1. Press the MENU key. 2. Press T to select "System" and "NMEA" and then press the ENTER key. NMEA setting menu 3.Press T to select the item to set and then press the ENTER key. 4.Press ...

Page 27 - Setting for dual frequency transmitting; Setting for “HF” connection

AP-2 Setting for dual frequency transmitting 1. Set the XDCR SELECT menu as follows (see page 11 and 12). 2. Press the [PWR] key to turn the power off, and turn it on again.3. Press the MENU key to show the menu.4. Select the [Sounder] and press the ENTER key.5. See the section "1.19.1 Sounder m...