Page 3 - SAFETY INSTRUCTIONS; WARNING; CAUTION; If the antenna unit is installed at a
i SAFETY INSTRUCTIONS WARNING Radio FrequencyRadiation Hazard Do not open the equipmentunless totally familiar withelectrical circuits andservice manual. Only qualified personnelshould work inside theequipment. Wear a safety belt and hardhat when working on theantenna unit. Serious injury or death c...
Page 4 - ii; SYSTEM CONFIGURATIONS
ii SYSTEM CONFIGURATIONS 12 - 24 VDC Display unit RDP-152 100/110/220/230 VACfor M1835 External buzzer Echo sounderGPS navigatorAIS, etc. Rectifier PR-62 Remote display : Basic configuration Heading sensor MODEL 1835 Antenna unitRSB-0071-057 Echo sounderGPS navigatorAIS, etc. ECONOMY RANGE TLL GAIN ...
Page 5 - iii; EQUIPMENT LISTS; Standard supply; Name
iii EQUIPMENT LISTS Standard supply Note: The name for MODEL1835, MODEL1935, MODEL1945 is shortened to M1835, M1935, M1945 in this manual. Name Type Code No. Qty Comment Display unit RDP-152 - 1 Antenna unit RSB-0071-057 - 1 Unit for M1835 XN10A-RSB-0070-064 Unit for M1935, 24 RPM XN10A-RSB-0073-064...
Page 6 - iv; Optional supply
iv Optional supply Name Type Code No. Qty Comment Rectifier PR-62 - 1 For M1835 RU-3423 - For M1935/1945 External buzzer OP03-21 000-030-097 1 Cable assy. MJ-B24LPF0010-100+R 000-147-880-12 1 For remote display, 10 m MJ-B24LPF0010-200+R 000-147-881-12 1 For remote display, 20 m MJ-B24LPF0010-300+R 0...
Page 7 - HOW TO INSTALL THE SYSTEM; Display Unit; How to install the display unit; How to install the display unit on a desktop or the overhead
1-1 1. HOW TO INSTALL THE SYSTEM 1.1 Display Unit Select a location for the display unit by following the information shown below. • The unit is waterproof, but FURUNO recommends that you install the display unit in a cabinet. • Keep the unit away from direct sunlight. • The temperature and humidity...
Page 8 - How to install the display unit in a console
1-2 How to install the display unit in a console Follow the procedure shown below to install the display unit in a console. 1. Prepare a hole in the location whose dimensions are 274 (W) x 252 (H) mm.2. Make four pilot holes. See the outline drawing at the back of this manual for additional infor- m...
Page 9 - How to select the location for the antenna unit; Normal position of the antenna unit on the sailboat and powerboat
1-3 1.2 Antenna Unit for MODEL1835 How to select the location for the antenna unit When you select an installation location for the antenna unit, remember the following points. • Install the antenna unit on a solid location, for example radar arch or on a mast on a platform. (For sailboats, a mounti...
Page 10 - How to install the antenna unit; Platform
1-4 How to install the antenna unit 1. Open the packing box of the antenna unit with great caution.2. Loosen the four bolts at the base of the radome to remove the radome cover. Antenna unit The location where you install the antenna unit must be parallel to the waterline. Make five holes in the ins...
Page 11 - How to fasten the radome base to the platform; Wiring and preparation; Remove three shield covers in the radome.; Shield cover
1-5 How to fasten the radome base to the platform Wiring and preparation 4. Make a hole of at least 20 millimeters in diameter through the deck or bulkhead to run the sig- nal cable. (To prevent electrical interference, do not run the signal cable near other electrical equipment. Do not run the cabl...
Page 14 - How to install the optional mounting bracket; Mounting bracket kit; How to assemble and install the optional mounting bracket; (B) Fastening antenna to mounting bracket
1-8 How to install the optional mounting bracket The optional mounting bracket lets you fasten the antenna unit to a mast on a sailboat. Mounting bracket kit Type: OP03-92 Code No.: 008-445-070 Assemble the mounting bracket and fasten the mounting bracket to a mast. Fasten the antenna unit to the br...
Page 15 - ment. Also do not run the cable in parallel to power cables.
1-9 1.3 Antenna Unit for MODEL1935/1945 How to select the location for the antenna unit • The antenna unit is installed either on top of the wheelhouse or a platform on the radar mast. Install the antenna unit where there is a good complete view. Any obstruction causes blind sec-tors. For example, a...
Page 16 - Installation procedure; How to fasten the radiator to the radiator bracket; Remove the radiator cap from the radiator bracket.; Flat washer
1-10 Installation procedure Refer to the outline drawing at the back of this manual for the dimensions. Make five holes in the platform. Four holes to fasten the antenna unit and one hole for the signal cable. How to fasten the radiator to the radiator bracket See the packing list at the back of thi...
Page 17 - • Use the outside holes; How to use outside holes of the antenna housing; Location of rubber mat; The radiator may be damaged.
1-11 How to install the antenna unit You can install the antenna unit by one of the two methods shown below. • Use the outside holes • Use the inside holes How to use outside holes of the antenna housing Use the hex head bolts (supplied) to install the antenna unit as shown in the illustration below...
Page 19 - How to use the inside holes of the antenna housing; Loosen four bolts on the cover to open the antenna unit.; OR
1-13 8. Apply the silicone sealant to the ground terminal and ground point as shown below. How to apply the silicone sealant to the ground point and ground terminal How to use the inside holes of the antenna housing This method requires removal of the RF unit from the antenna unit to access the insi...
Page 20 - Antenna unit chassis, upper chassis separated
1-14 Antenna unit chassis, upper chassis separated 7. Set the corrosion-proof rubber mat (supplied) to the support platform. 8. Cut the rubber bushings in the fixing holes and put four bolts from the inside of the lower chas- sis. Fasten the lower chassis to the support platform with the spring wash...
Page 21 - How to connect the signal cable; Antenna unit chassis, cover opened
1-15 How to connect the signal cable The signal cable runs from the display unit to the antenna unit. To reduce the electrical interfer-ence, do not run the signal cable near other electrical equipment. And do not run the cable in par-allel to power cables. Put the cable through the hole and apply t...
Page 24 - This page is intentionally blank.
Page 25 - CABLE CONNECTION; Standard Connection; Connect all cables at the rear of the display unit.
2-1 2. CABLE CONNECTION 2.1 Standard Connection Connect all cables at the rear of the display unit. Display unit, rear view Antenna cable MJ-B24LPF0002-xxx+R or MJ-B24LPF0005-yyy+R CAUTION Ground terminalConnect ground wire between here andship's ground. Ground theequipment toprevent interference. C...
Page 26 - Data Signal Port
2-2 2.2 Data Signal Port Connect external equipment(s) to the ports on the rear panel as shown below. The Model 1835/1935/1945 can receive the following NMEA 0183 format sentence from other equipment. • Position GNS>GGA>RMC> GLL • Course true VTG>RMC • Course magnetic VTG>RMC (true) •...
Page 27 - HOW TO SET THE EQUIPMENT; How to Set the Language; key to turn on the power.; The window shown below appears.; ENTER
3-1 3. HOW TO SET THE EQUIPMENT 3.1 How to Set the Language At the first power application after installation, select a language as follows. 1. Press /BRILL key to turn on the power. "Now Initializing" appears and after a while the window below appears. 2. Use the cursor pad to select a lang...
Page 28 - How to Set the Purpose
3-2 3.2 How to Set the Purpose Set the purpose of the radar. 1. Press the MENU key. The main menu appears on the screen. 2. Press T or S on the cursor pad to select Factory . The factory menu title bar appears in gray on the right of the screen. 3. While you press the CANCEL/HL OFF k ey, press the M...
Page 29 - How to Enter the Initial Settings; Installation; Basic Settings
3-3 3.3 How to Enter the Initial Settings After you set the purpose of the radar, enter the initial settings as follows. 1. On the main menu, press T or S to select Installation . 2. Press the ENTER key. The Installation menu becomes active and the cursor moves to the right column. 3. Press T or S t...
Page 30 - Heading Adjustment; Heading Adjust
3-4 Antenna Rotation: "Rotate" (default setting) transmits the radar pulses with rotating the antenna. "Stop" transmits the radar pulses without rotating the antenna. Antenna Height: Set the height of the antenna above the water surface. The options are 5, 10, 15, 20, 30, 40 and 50 m...
Page 31 - Examples of wrong and correct sweep timings
3-5 How to automatically set the equipment The equipment automatically adjusts the tuning, timing and video. Note: Before you do this procedure, tramsmit the radar more than 10 minutes on a long range and check that Sector Blank is OFF. 1. Transmit on the maximum range. 2. Select Auto Install Setup ...
Page 32 - Manual MBS Adjustment; MBS Adjust; Video Initial Adjustment; Transmit the radar and set the radar as follows.; key to show the setting window.; ARPA Adjustment
3-6 Manual MBS Adjustment Reduce the main bang (black hole), which appears at the display center on short ranges, as fol-lows. 1. Transmit the radar on the shortest range.2. Open the Installation menu and select MBS Adjust . 3. Press the ENTER key to show the setting window. 4. Press the cursor pad ...
Page 33 - OPTIONAL EQUIPMENT; Necessary parts; For details, see the packing list attached to the kit.; Remove five connector nuts.
4-1 4. OPTIONAL EQUIPMENT 4.1 ARP Kit ARP-11 The ARP kit provides automatic radar plotter functions to this radar. Necessary parts Name: ARP kit Type: ARP-11 Code no.: 008-523-050 For details, see the packing list attached to the kit. 1. Unscrew 12 screws and five connector nuts at the rear of the d...
Page 34 - Lift the cover slowly and open it as shown below.; Cover
4-2 2. Lift the cover slowly and open it as shown below. 3. Mate P107 on the ARP board to J214 on the 03P9474 board and fasten the ARP board with four screws. 03P9474 J214 Cover Open this direction. Take care not to damagethis cable assembly. ARP board Comfirm that rubber gasket is set securely in t...
Page 36 - Connection of Buzzer and/or Remote Display; External buzzer
4-4 4.2 Connection of Buzzer and/or Remote Display You need the cables shown below to connect the optional external buzzer and remote display. • Two-way cable MJ-A10SPFW0001+R • MJ-A7SPF0007-050C • MJ-B24LPF0010-xxx+R (xxx: 100, 200 or 300) External buzzer When a target enters (exists) in the guard ...