Fujitsu ASTG30LFCC - Manuals

En-6 To Select Mode Operation 1 Press the START/STOP button (Fig.5 M ). The indoor unit’s OPERATION Indicator Lamp (green) (Fig. 3 5 ) will light. The air conditioner will start operating. 2 Press the MODE button (Fig.5 G ) to select the de- sired mode. Each time the button is pressed, the mode will...

En-7 OPERATION To Stop Operation Press the START/STOP button (Fig. 5 M ). The OPERATION Indicator Lamp (green) (Fig.3 5 ) will go out. About AUTO CHANGEOVER Operation AUTO: ● When AUTO CHANGEOVER operation fi rst selected, the fan will operate at very low speed for about a few minutes, during which ...

En-8 To Cancel the Timer Use the TIMER MODE button to select “CANCEL”.The air conditioner will return to normal operation. To Change the Timer Settings 1. Follow the instructions given in the section “To Use the ON Timer or OFF Timer” to select the timer setting you wish to change. 2. Press the TIME...

En-9 SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped. To Use the SLEEP Timer While the air conditioner is operating or stopped, press the SLEEP button (Fig. 5 J ). The indoor unit’s OPERATION Indicator Lam...

En-10 ADJUSTING THE DIRECTION OF AIR CIRCULATION ● Adjust the up, down, left, and right AIR directions with the AIR DIRECTION buttons on the Remote Controller. ● Use the AIR DIRECTION buttons after the Indoor Unit has started operating and the air fl ow-direction louvers have stopped moving. DANGER!...

En-11 To select SWING Operation Press the SWING button (Fig. 5 P ). The SWING Display (Fig. 6 \ ) will light. Each time the SWING button is pressed, the swing operation will change in the following order. To stop SWING Operation Press the SWING button and select STOP. Air fl ow direction will return...

En-12 10 °C HEAT OPERATION To use 10 °C HEAT OPERATION Press the 10 °C HEAT button (Fig.5 H ) The OPERATION indicator lamp (green) (Fig. 3 5 ) will go out, and the ECONOMY indicator lamp (green) (Fig. 3 7 ) will light. To stop 10 °C HEAT OPERATION Press the START/STOP button (Fig.5 M ) Then the OPER...

En-13 Cleaning the Intake Grille 1. Remove the Intake Grille. 1 Place your fi ngers at both lower ends of the grille panel, and lift forward; if the grille seems to catch partway through its movement, continue lifting upward to remove. 2 Pull past the intermediate catch and open the Intake Grille wi...

En-14 Air Cleaning Filter Installation 1. Open the Intake Grille and remove the Air fi lters. 2. Install the Air cleaning fi lter set (set of 2). 1 Set the air cleaning fi lter into the air cleaning fi lter frame. 2 Engage the latch at both ends of the filter with the 2 hooks at the rear of the air ...

En-15 Filter Indicator Reset (The special setting) • Can be used if set correctly during installation. Please consult authorized serviceman when using this function. • It lights on when it is time to clean the air fi lters. Clean the fi lter referring to “CLEANING AND CARE”. After cleaning, press th...

En-16 TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical breaker and consult authorized service personnel.Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. Always be sure to ...

En-17 TROUBLESHOOTING Symptom Problem See Page CHECK ONCE MORE Doesn’t operate at all: ● Has the circuit breaker been turn off? ● Has there been a power failure? ● Has a fuse blown out, or a circuit breaker been tripped? — ● Is the timer operating? 8 - 9 Poor Cooling (or Heating) performance: ● Is t...

En-18 OPERATING TIPS Multi-type Air conditioner This indoor unit can be connected to a multi-type outdoor unit depending on model. The multi-type air conditioner allows multiple in-door units to be operated in multiple locations. The indoor units may be operated simultaneously, in accordance with th...