Frigidaire PMOS1980AF - Manuals

Materials you can use in microwave oven Browning dish Follow manufacturer instructions. The bottom of browning dish must be at least 3/16 inch (5mm) above the turntable. Incorrect usage may cause the turntable to break. Dinnerware Microwave-safe only. Follow manufacturer's instructions. Do not use c...

Glass Turntable Round Wire Rack Wire Rack Air Fry Tray Air Fry Pan 8 NAMES OF OVEN PARTS AND ACCESSORIES NOTE NOTE CAUTION The Air Fry Pan and Air Fry Tray are designed for Air Fry cooking only and should not be used for any other microwave cooking. Always use oven mits when handling hot items. The ...

• Before operating your new appliance make sure you read and understand this Use and Care Guide completely. • The clock can be disabled when the microwave is first plugged in and the CANCEL key is selected.To re-enable the clock follow clock instructions. 1. XX:XX (current time will display after 2 ...

9 OPERATION Air Fry The Air Fry feature works best when using the Air Fry Pan and Air Fry Tray with packaged and convenience foods and can be programmed for temperatures between 100°F and 425°F using preset temperatures. Follow the recipe or package directions for food preparation quantity, time, an...

1. 2. 8 3. CONVECT COOK 4. 5. START ( When oven is preheated it will beep. ) Temperature will display if no action is taken. 6. Place food in oven and enter time 7. COOK COOK 5 0 0 START OPERATION Convection Cooking For Best Results... Always use the round wire rack when convection cooking. Reduce p...

POPCORN 3. Touch POPCORN Amount X1 3.3 oz X2 3.0 oz X3 1.75 oz • Suppose you want to cook 3.0 oz. popcorn. Touch: Display Shows: 1. POPCORN 2. START Time counting down OPERATION MELT/SOFTEN • S uppose you want to melt 2 sticks of Butter. 1. / 2. START 3. 2 4. START MELT SOFTEN X1 Touch: Display Show...

1. SENSOR COOK 2. SENSOR COOK 3. SENSOR COOK 4. START SENSOR COOK Suppose you want to cook a frozen dinner. Touch: Display Shows: OPERATION • NOTE When the food is near completion, the display will show time count down. Touch sensor cook once, Bacon displays, then Touch start to enter the slice sett...

• Suppose you want to set a 2-stage cook cycle. The first stage is a 3 minute cook time at 80%cook power then a 7 minute cook time at 50%cook power. MULTI-STAGE COOKING For best results, some recipes call for different power levels during a cook cycle. You can program your microwave for two power le...

MICROWAVE AT LOWER POWER LEVEL Your Over the Range Microwave Oven can be programmed for 99 minutes 99 seconds (99 :99). Always enter the seconds after the minutes, even if they are both zeros. • Suppose you want to cook for 2 minutes at 90% power. 1. 2. 3. 4. Touch: Display Shows: START POWER CHART ...

1. x 4 SETTING FILTER Touch: Display Shows: 2. START SETTING WEIGHT LB/KG • Suppose you want to change from lb to kg. 1. x 3 2. START Touch: Display Shows: OPERATION The display will scroll. When you see the desired setting touch Start . DEMO SETTING • Suppose you want to turn on Demo Mode . 1. x 5 ...

Troubleshooting Check your problem by using the chart below and try the solutions for each problem. If the microwave oven still does not work properly, contact the nearest authorized service center. TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Oven will not start • Electrical cord for oven is not plugged ...

EXTERIOR The outside surface is precoated steel and plastic. Clean the outside with mild soap and water; rinse and dry with a soft cloth. Do not use any type of household or abrasive cleaner. Disconnect the power cord or leave the door open to deactivate the oven during cleaning. Disconnect the powe...

Disconnect the power cord or leave the door open to deactivate the oven during cleaning. Disconnect the power cord before replacing filters and lights. 4. Remove the charcoal filter by pushing the top of the filter inwards, then pull it forward out from the unit. Charcoal filter replacement Charcoal...

WARNING Disconnect the power cord before cleaning or leave the door open to deactivate the oven during cleaning. CLEANING THE GREASE FILTER The oven ventilation grease filters should be removed and cleaned often; generally at least once every month. CAUTION To avoid risk of personal injury or proper...

AC Line Voltage: Single phase 120V, 60Hz, AC only AC Power Required: Output Power*: 1000 W Frequency: 2450 MHz (Class B/Group2)** Outside Dimensions: ”(H) Cavity Dimensions:Microwave oven Capacity***:Cooking Uniformity: Turntable Weight:Work/Night Light:Oven Light: SPECIFICATIONS Place one cup of wa...

Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintaine...

welcome home Frigidaire.com 1-800-374-4432 Frigidaire.ca 1-800-265-8352 owner support accessories service Our home is your home. Visit us if you need help with any of these things: registration (See your registration card for more information.)

Installation Instructions • Tape measure • Hole saw • Stud finder or hammer • Level • Duct and masking tape • Scissors • #1 Phillips screw driver • Electric drill • 3/16”, 1/2”, 5/8” drill bit • Filler wood blocks for recessed bottom cabinets • Tin snips Mounting Space Tools you will need: • The spa...

PLACEMENT OF THE MOUNTING PLATE 1 Installation Instructions Find the studs, using one of the following methods:A. Stud finder – a magnetic device which locates nails. B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location. After locating ...

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Installation Instructions Plate position-beneath flat bottom cabinet to Cooktop C 3/8" TO EDGE             ...

Installation Instructions ALIGNING THE WALL PLATE D. Area E Hole A Hole B Centerlinenotches Draw a Vertical Line on Wall from Center of Top Cabinet Draw a horizontal line on wall at the bottom of “Rear Wall Template”. Horizontal Line Horizontal Line CL 3/8" TO EDGE %#76+10Ä+(':*#756#&#2614+5...

INSTALLATION TYPES This microwave oven is designed for adaptation to the following three types of ventilation: OUTSIDE TOP EXHAUST (VERTICAL DUCT) OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) See page 2 0 Adaptor in Place for Outside Top Exha ust 2 B Adaptor Must Be Moved to the Back for Outside Back Exha...

INSTALLATION OVERVIEW IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration. • Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched. ...

Installation Instructions Cabinet Front Cabinet Bottom Shelf Filler Block Microwave Oven Top Attach the microwave oven to the top cabinet . Equivalent to Depth of Cabinet Recess 3 MOUNT THE MICROWAVE OVEN Self-Aligning Screw 4 2 Rotate front of oven up against cabinet bottom. Insert a self-aligning ...

Installation Instructions 5 MOUNT THE MICROWAVE OVEN (cont.) 8 7 Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) Insert 2 self-aligning screws through outer top cabinet holes. Turn two fu...

Installation Instructions Close the microwave door. Plug in microwave oven or reconnect power. Press the bottom of charcoal filter to place it into the correct position. A5. INSTALLING OR CHANGE THE CHARCOAL FILTER(cont.) A 5.5 A 5.6 A 5.7 Then close vent's cover. EN-13

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH 5 Ft. (1.5 m) x ( ) = Ft. or m Rectangular-to- Round Transition Adaptor* Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m 90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m 45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m 90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or ...

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) 12 Ft. (3.6 m) Straight Duct (6”/15.2 cm Round) 5 Ft. (1.5 m) x (1) = 5 Ft. (1.5 m) Rectangular-to- Round Transition Adaptor* Equivalent lengths of duc...

• • Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate. Back of Microwave Installation Instructions PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST B1. You need to cut an opening in the rear wall for outside exhaust. • Read the instructions on the REAR...

ATTACH THE MOUNTING PLATE TO THE WALL B3. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. Wall Mounting Plate ...

AFTER: Fan Blade Openings Facing Back Place the blower unit back into the opening. Replace the blower plate in the same position as before with the screw. Make sure the screw is tight. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of t...

Installation Instructions 3 MOUNT THE MICROWAVE OVEN B6. 8 7 5 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) Filler Block Equivalent to Depth of Cabin...

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabi...

3 MOUNT THE MICROWAVE OVEN 2 Rotate front of oven up against cabinet bottom. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep...

4 8 7 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) Filler Block Equivalent to Depth of Cabinet Insert 2 self-aligning screws through outer top cabine...

Remove all packing material from the microwave oven. 2. Make sure the microwave oven has been installed according to instructions. 1. BEFORE YOU USE YOUR MICROWAVE Ensure proper ground exists before use INST ALLA TION INSTR UCTIONS 3. D G DDDDDDD Installation Instructions ring a nd glas s tra y i n ...

Printed in China      Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LE...

LEA CUIDADOSAMENTE. CONSERVE ESTAS INSTRUCCI . ONES. Lea estas instrucciones completamente y con atención. • • • • • o ¿Preguntas? Llame al • Las fallas del producto que resulten de una instalación incorrecta no están cubiertas bajo la garantía. conserve estas instrucciones para uso futuro del inspe...

CONTENIDO Información general Guía de la instalación paso a paso B A Instrucciones de instalación Recirculación Instalación del horno microondas ...................... 19 Preparación del gabinete superior ..................... 17 Montaje de la placa de instalación en la ................................

INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Instrucciones de instalación Este product require un tomacorriente de tres clavijas con puesta a tierra. Antes de proceder con la instalación del electrodoméstico, el instalador debe realizar una verificación de la continuidad de la puesta a tierra del tomac...

Tornillos para madera Tornillos de fiador (y tuercas de mariposa) Tornillos autoalinea -ntes para máquina Moldura aislante de nylon (para los gabinetes metálicos) • • • DAÑOS-ENVÍO (TRANSP -ORTE)/INSTALACIÓN Instrucciones de instalación PIEZAS INCLUIDAS KIT DE FERRETERÍA PIEZA CANTIDAD 1 1 2 INSTRUC...

HERRAMIENTAS NECESARIAS Instrucciones de instalación • Mètre• scie trépan• Trouveur de goujons ou marteau• Niveau• Ruban adhésif et de masquage• Ciseaux • n #1 tournevis cruciforme• Perceuse électrique• Foret 3/16 ’’, 1/2 ’’, 5/8 ’’• Blocs de bois de remplissage pour armoires à fond encastré • Cisai...

COLOCACIÓN DE LA PLACA DE INSTALACIÓN 1 Instrucciones de instalación 1 LOCALIZACIÓN DE LAS VIGAS DE LA PARED B. A. 2 Vigas de la pared Centro 3 Caja de cartón Tire de la caja de cartón hacia arriba, para separarla del horno. 2 Espuma de poliestireno 3 1 Tornillos Tornillos Placa de instalación 5 4 C...

C . C 3/8" TO EDGE                    NOTE: IT IS V ERY IMPORT ANT TO READ AND F OLLOW THE DIRECTION S IN ...

Instrucciones de instalación D. CL 3/8" TO EDGE NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust ...

A TIPOS DE INSTALACIÓN (A Elección Entre A, B o C) Este horno microondas está diseñado para adaptarse a los tres tipos siguientes de ventilación: A. Extracción superior externa (conducto vertical) B. Extracción trasera externa (conducto horizontal) C. Recirculación (sin conducto de extracción) EXTRA...

Instrucciones de instalación A1. 1 2 A RECIRCULACIÓN (Sin Conducto De Extracción) DESCRIPCIÓN GENERAL DE LA INSTALACIÓN C1. Montaje de la placa de instalación en la pared C2. Preparación del gabinete superior C3. Verificación del conjunto del Placa del Ventilador C4. Instalación del horno microondas...

Instrucciones de instalación A3. A4. Placa del Ventilador · A2. · Lea las instrucciones de la sección PLANTILLA PARA ELGABINETE SUPERIOR.·Adhiera con cinta la plantilla al gabinete superior. USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL ÁREA DE DICHO GABINETE Es necesario taladr...

5 8 7 A4. Instale los filtros de grasa. Consulte el Manual del usuario provisto con el microondas. Instrucciones de instalación INSTALACIÓN DEL HORNO MICROONDAS (cont.) Inserte 2 tornillos autoalineantes a través de los agujeros exteriores del gabinete superior. Apriete cada uno de, los tornillos do...

Instrucciones de instalación A 5.6 A 5.7 Presione la parte inferior del filtro de carbón para colocarloen la posición correcta. Cierre la puerta del microondas. Enchúgelo o reconecte la energía eléctrica. A 5.5 A5. Instalación o cambiar del filtro de carbón (Cont.) Luego cierre la tapa del respirade...

= x PIEZAS DEL CONDUCTO Adaptador de unión entre el conducto rectangular y el redondo* Pies o m (metros) = ( ) x 5 pies (1,5 m) Tapa de salida a la pared = ( ) x 10 pies (3 m) Codo de 90° = ( ) x 5 pies (1,5m) Codo de 45° = ( ) x 25 pies (7,6 m) Codo de 90° = ( ) x 5 pies (1,5 m) Codo de 45° = ( ) x...

EXTRACCIÓN SUPERIOR EXTERNA (SÓLO EJEMPLO) La siguiente tabla contiene un ejemplo de uno posible instalación de un sistema de conducto de extracción. Instrucciones de instalación EXTRACCIÓN TRASERA EXTERNA (SÓLO EJEMPLO) La siguiente tabla contiene un ejemplo de una posible instalación de un sistema...

· Parte trasera del microondas Instrucciones de instalación B1. · B2 . B Placa del ventilador 3/8" T O E DGE NO TE : IT IS VE RY IM POR T ANT TO RE AD AND FOL L OW TH E DIR EC TIONS IN T HE IN STA LLATIO N INS TR UCTIO NS BEFO RE PR O C EED ING W ITH TH IS RE AR WALL TEMP LATE . T his Re ar Wall...

Instrucciones de instalación B3. · Pared Placa de instalación Tornillo fiador El espacio que ocupan los tornillos fiadores es superior al grueso de la pared Tuercas de mariposa Para utilizar tornillos de fiador: Extremo de tornillo 12 2 1 B5. Extremo B Extremo A Parte trasera del microondas Motor de...

Instrucciones de instalación Vuelva a colocar el ventilador dentro de su abertura. B5. Gire el ventilador hacia la izquierda 180 °. Antes del giro Después del giro Antes de la reorientación Después de la reorientación Cables orientados a través del lado derecho Cables orientados a través del lado iz...

C2. · · Instrucciones de instalación C3. Placa del ventilador Tornillo del motor del ventilador Parte trasera del microondas 2 Extremo B Extremo A 1 3 Parte trasera del microondas Parte trasera del microondas Parte trasera del microondas Parte trasera del microondas DESPUÉS: Aberturas de las aletas ...

3 2 1 Placa del ventilador Adaptador de extracción Regulador de extracción Parte trasera del microondas · C3. 5 Parte trasera del microondas 6 7 Parte trasera del microondas Adaptador Guía C 4. C 5. Instrucciones de instalación AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRAC- CIÓN SUPERIOR EXTER...

4 8 7 Parte delantera del gabinete Estante inferior del gabinete Bloque de relleno Parte superior del horno microondas Fije el horno microondas al gabinete superior. Instrucciones de instalación Parte trasera del microondas Placa del ventilador Regulador de extracción 5 C6. C5. 1 2 C7. Conducto de l...

2. 1. ANTES DE USAR EL HORNO MICROONDAS INSTRUCCIONES DE INSTALACIÓN 3. Instrucciones de instalación 4. 7. 6. INSTRUCCIONES DE INSTALACIÓN GUÍA DE USO Y CUID ADO REGISTR O DEL PRODUCT O Lea el manual de use y cuidado. Vuelva a colocar el fusible correspondiente o encienda de nuevo el disyuntor. 5. 8...