Frigidaire LI30KC/316902495 - Manuals

Frigidaire LI30KC/316902495 – Manual in PDF format online.

Manuals:

Manual

Manual Frigidaire LI30KC/316902495

Summary

Page 2 - Serial Plate; Record model & serial numbers here; PRODUCT RECORD AND REGISTRATION

Thank you for choosing Frigidaire. This Use & Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new appliance.We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you, please use th...

Page 3 - To reduce risk of fire and to properly exhaust

Save these instructions for future references Approved for residential appliances For residential use only Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION based on...

Page 4 - Always leave safety grills and filters in place.Without; IMPORTANT SAFETY INSTRUCTIONS; Not Use This Hood With Any External Solid State; WARNING

4 WARNING TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close - fitting lid, cookie sheet, or other metal tray, then turn off the gas burner or the electric element. BE CAREFUL TO PREVENT BURNS. If the flames do not go ...

Page 5 - Parts included in your hood; - 75W max, 120V incandescent light bulb; Tools/Materials required; Four flat head wood screws or machine screws; ELECTRICAL REQUIREMENTS; recommended that a qualified electrician determine that; National Fire Protection Association; the rating of the appliance as specified on the

LIST OF MATERIALS LIST OF MATERIALS Parts included in your hood 4 - 0.45 x 1.3 cm mounting screws 3¼ ” x 10” (8.3 x 25.4 cm) rectangular metal vent system. NOTE: An optional 7” round duct kit is available. You can order this kit as part number 5304487139 . Parts Needed 2 - UL listed wire connectors ...

Page 6 - IMPORTANT; Observe all governing codes and ordinances.; installation clearances specified on the model/serial; For Mobile Home Installations; The installation of this range hood must conform to the; Cabinet Dimensions; LOCATION REQUIREMENTS

IMPORTANT Observe all governing codes and ordinances. It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left side (See page 2 for location). Range hood location...

Page 7 - NOTE; Flexible vent is not recommended. Flexible vent; VENTING REQUIREMENTS

Vent system must terminate to the outdoors. Do not terminate the vent system into an attic or other enclosed area. Do not use a 4” (10.2 cm) laundry-type wall cap. Use a 3¼ ” x 10” (8.3 x 25.4 cm) rectangular metal vent. Rigid metal vent is recommended. Plastic or metal foil vent is not recommended....

Page 8 - Before making cutouts, make sure there is; Select a flat surface for assembling the range hood.; Determine Wiring Hole Location; Determine and clearly mark a vertical centerline on

8 PREPARE THE LOCATION NOTE Before making cutouts, make sure there is proper clearance within the ceiling or wall. Disconnect power. Select a flat surface for assembling the range hood. Place covering over that surface. Lift the range hood and set it upside down onto covered surface. If cabinet has ...

Page 9 - Choose venting exhaust discharge from the various; Style 1 - Recirculating Hood version; For this installation, go to “Install Range Hood; Roof Venting; cutout on the underside of cabinet top and bottom:; Wall Venting; PREPARE THE LOCATION

9 To wire through top: Mark a line distance (A) from the right of the centerline on the underside of the cabinet. Mark the point on this line that is 7 ⁄ 8 ” (2.2 cm) from back wall. Drill a 1¼” (3.2 cm) diameter hole (B) through the cab net at this point. To wire through wall: Mark a line distance ...

Page 10 - Install Vent System; Use caulking to seal exterior wall or roof opening; INSTALL RANGE HOOD; cm) rectangular vent connector on the inside of; final location by centering beneath cabinet. Mark on; cm) Rectangular Vent Transition to Round Vent; to Round Vent Transition; To make a circular vent opening on the underside of the

10 Install Vent System Install vent through the vent opening in upper cabinet or wall. Complete venting system according to the selected venting method. See “Venting Requirements” section. Use caulking to seal exterior wall or roof opening around the cap. INSTALL RANGE HOOD (Ducted version) NOTE You...

Page 11 - either side of the hood center to accommodate; Power Supply Cable Installation; Do not reconnect power until the installation is; INSTALLING THE HOOD

11 Use ¹⁄ 8 ” (3 mm) drill bit and drill 4 pilot holes as shown. NOTE: Make the drill holes on the thin area of the slot. Install the 4 - .45 cm x 1.3 cm mounting screws in pilot holes. Leave about ¼” (6.4 mm) space between screw heads and cabinet to slide range hood into place. For roof installatio...

Page 12 - terminal box. Failure to do so can result in death,; to green ground screw in terminal box and securely tighten.; To get the most efficient use from your new

1 INSTALLING THE HOOD INSTALL RANGE HOOD (Recirculating version) Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood (See slots dimensions on page 6). Set range...

Page 13 - Recirculation Vent Cover; For installations which are recirculating the air exhaust,; Range Hood Controls; RANGE HOOD USE

1 Remove the power supply knockout from the top or rear of the vent hood (depending on the incoming location of your home power supply cable) and install a UL listed or CSA approved ½” strain relief. Using 2 or more people, lift the hood into final position. Feed enough electrical wire through the ½...

Page 14 - Charcoal / Grease Filter Accesory Kit; For recirculating vent hood, an optional charcoal filter is; RANGE HOOD CARE

14 Replace screw in the filter retainer. To clean grease filter, soak the filters in hot water using a mild detergent. Rinse well and shake to dry. Or place in upper rack of dishwasher to clean. NOTE: Do not use ammo- nia. The aluminum on the grease filter will corrode and darken. NOTE: You can use ...

Page 15 - TROUBLESHOOTING; Problem; the outside wind flow.

1 TROUBLESHOOTING Problem Possible Causes Solutions After installation, the unit doesn’t work. 1. The power line and the cable locking connector is not connecting properly. 1. Check the power connection with the unit is connected properly. 2. The wires from the switches are disconnected or loose. 2....

Page 16 - Warranty; USA

1 Warranty Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and maintained in accord...

Page 17 - printed in Mexico