Frigidaire LFMV1846VFA - Manuals

Frigidaire LFMV1846VFA – User Manual, Installation Manual in PDF format online.

Manuals:

User Manual
Installation Manual

User Manual Frigidaire LFMV1846VFA

Installation Manual Frigidaire LFMV1846VFA

Summary

Page 3 - CONTENTS; General information; Installation Instructions; Attach Mounting Plate to Wall

CONTENTS General information Important Safety Instructions .................................. 3 Electrical Requirements .......................................... 3 Damage – Shipment/Installation.............................. 4 Parts Included.............................................................

Page 5 - If the unit is damaged in shipment,; return the; If the unit is damaged by the customer,; repair or; If the unit is damaged by the installer; Some extra parts are included.; HARDWARE PACKET; PART; PARTS INCLUDED; ADDITIONAL PARTS; Shelf; For some models

PART QUANTITY Wood Screws 2 ( 1 ⁄ 4 “ x 2“) Toggle Bolts (andwing nuts) ( 3 ⁄ 16 “ x 3“) Self-Aligning Machine 3 Screws ( 1 ⁄ 4 “-28 x 3 1 ⁄ 4 “) Nylon Grommet(for metal cabinets) 1 • If the unit is damaged in shipment, return the unit to the store in which it was bought for repairor replacement. • ...

Page 6 - bottom cabinets; Mounting Space; or more from the; Backsplash; Clearance

Installation Instructions • Tape measure• Hole saw• Stud finder or hammer• Level• Duct and masking tape• Scissors • #1 Phillips screw driver• Electric drill• 3/16”, 1/2”, 5/8” drill bit• Filler wood blocks for recessed bottom cabinets • Tin snips Mounting Space Tools you will need: • The space betwe...

Page 7 - Draw a line down the center of the studs.; FINDING THE WALL STUDS; Pull the carton up and off the oven.; Screws; Cut the middle of the outer protective plastic bag to; Filters and Turntable

PLACEMENT OF THE MOUNTING PLATE 1 Installation Instructions Find the studs, using one of the followingmethods: A. Stud finder – a magnetic device whichlocates nails. B. Use a hammer to tap lightly across themounting surface to find a solid sound.This will indicate a stud location. After locating the...

Page 8 - DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET; THE MICROWAVE MUST BE LEVEL.

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Installation Instructions Plate position flat bottom cabinet to Cooktop C 3/8" TO EDGE              ...

Page 9 - ALIGNING THE WALL PLATE; NOTE: DO NOT MOUNT THE PLATE AT THIS; Holes A and B are inside area E. If neither of; at least one wood screw; m ounted; firmly in a stud; to support the weight of the; Set the mounting plate aside

Installation Instructions ALIGNING THE WALL PLATE D. Area E Hole A Hole B Centerlinenotches Draw a Vertical Line on Wall from Center of Top Cabinet Draw a horizontal line on wall at thebottom of “Rear Wall Template”. Horizontal Line Horizontal Line CL 3/8" TO EDGE %#76+10Ä+(':*#756#&#2614+52...

Page 10 - INSTALLATION TYPES; OUTSIDE TOP EXHAUST; Adaptor in Place for; RECIRCULATING; NOTE: Read the pages 14-15 only if you plan to vent your exhaust to the

INSTALLATION TYPES This microwave oven is designed for adaptation tothe following three types of ventilation: B. Outside Back Exhaust (Horizontal Duct) proceed to that section. OUTSIDE TOP EXHAUST (VERTICAL DUCT) OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) See page 2 0 Adaptor in Place for Outside Top Ex...

Page 11 - INSTALLATION OVERVIEW; out from wall using adequate materials supporting

INSTALLATION OVERVIEW Attach Mounting Plate to WallPrepare Top Cabinet Mount the Microwave Oven IMPORTANT NOTES: • Make sure the screws for the blower motor and blowerplate are securely tightened when they are reinstalled.This will help to prevent excessive vibration. • Make sure the motor wiring ha...

Page 12 - MOUNT THE MICROWAVE OVEN; USE TOP CABINET TEMPLATE

Installation Instructions Attach the microwave oven to the top cabinet. Cabinet Front Cabinet Bottom Shelf Filler Block Microwave Oven Top Equivalent to Depthof Cabinet Recess 3 MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OV...

Page 13 - MOUNT THE MICROWAVE; packed with the microwave.; INSTALLING OR CHANGE; Unplug microwave oven or disconnect power.

Installation Instructions 5 MOUNT THE MICROWAVE OVEN (cont.) 8 7 Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.) Insert 2 self-aligning screwsthrough outer top cabinetholes. Turn two full tu...

Page 14 - Close the microwave door. Plug in microwave; A5. INSTALLING OR CHANGE

Installation Instructions Close the microwave door. Plug in microwave oven or reconnect power. Reinstall the vent by sliding the bottom of the vent into place. Push the vent top into position and slide right into place. Replace the two vent mounting screws located on top of the microwave using a #1 ...

Page 15 - Total Ductwork; Maximum duct length:; INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING; diameter duct is acceptable to use.

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular-to-Round 5 Ft. (1.5 m) x ( ) = Ft. or m Transition Adaptor* Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m 90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m 45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m 90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m...

Page 16 - Roof Cap; Wall Cap; Total Length; EXTERNAL EXHAUST DUCTING

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6”/15.2 cm Round) Rectangular-to-Round 5 Ft. (1.5 m) x (1) = 5 Ft. (1.5 m) Transition Adaptor* Equivalent lengths of duct...

Page 17 - REMOVE BLOWER PLATE

INSTALLATION OVERVIEW B1. Prepare Rear Wall B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave Oven IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to preve...

Page 18 - Roll the blower unit 90°

ATTACH THE MOUNTINGPLATE TO THE WALL B3. • Read the instructions on the TOP CABINETTEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on theTOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. Wall Mounting Plate Spa...

Page 19 - Remove the knockout plates in the back of the unit

Attach the exhaust adaptor to the rear of theoven by sliding it into the guides at the topcenter of the back of the oven. AFTER: Fan BladeOpenings Facing Back Place the blower unit back into the opening. Replace the blower plate in the same positionas before with the screw. Make sure the screw is ti...

Page 20 - IMPORTANT: If filler blocks are not; IMPORTANT: Do not grip or use the handle

Attach the microwave oven to the top cabinet. Installation Instructions 3 MOUNT THE MICROWAVEOVEN B6. FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to preventcuttin...

Page 22 - EXHAUST; Place the blower unit back into the opening.; with the top of the unit facing up.

USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET You need to drill holes for the top support screws, ahole large enough for the power cord to fit through,and a cutout large enough for the exhaust adaptor. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet....

Page 23 - IMPORTANT: If filler blocks are; Exhaust Adaptor; heat shield and door.

3 MOUNT THE MICROWAVEOVEN FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front ...

Page 24 - CONNECTING DUCTWORK; for high temperature applications.

4 Attach the microwave oven to the top cabinet. 8 7 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.) Filler Block Microwave Oven Top Equivalent to Depth of ...

Page 25 - BEFORE YOU USE YOUR MICROWAVE; INST; ring a nd glas s tray in; DDDDDDD; PRODU; Read the; REGIS; U SE; Replace house fuse or turn breaker back on.; FILL OUT PRODUCT R EGISTRATION CAR D

Remove all packing material from the microwave oven. 2. Make sure the microwave oven has beeninstalled according to instructions. 1. BEFORE YOU USE YOUR MICROWAVE Ensure properground existsbefore use INST ALLA TION INSTR UCTIONS 3. D G DDDDDDD Installation Instructions ring a nd glas s tray in cavit...

Page 26 - Printed in China

Printed in China ＂ 2 / 1 - 4 3/8＂ 3/8＂ 13-3/8＂ 2＂ 2＂ 12-1/2＂ 6-1/4＂＂ 2 3 / 7 2 - 9 ＂ 4 / 1 - 4 3/8＂ 3/8＂ 3/8＂ 2＂ 1/2＂ 13-3/8＂ 3/8" TO EDGE    ...