Frigidaire FRS184YC2 - Manuals

Attention 1. This illustration is for explanation purposes only. 4 3 1 Indoor unit Outdoor unit 5 6 Air filter More A B C 2. Copper tubes must be insulated independently More than 6.6' More than 1' More than 1.65 ' than 1.65' More than 6 " More than 6" More than 6 " 2 6 8 7 Parts list 10

1.58'' 7.91'' 5.31'' 1.58'' A B (A:33.31" B:10.83") =18000 Btu's (A:36.97" B:11.73") Indoor unit outline Installation plate the ceiling from the wall from the wall Refrigerant pipe 6" or more from 6 " or more hole (right) Ø 2.56" 6 " or more 3.39 " 4.21 " 1200...

Indoor unit installation Attention Fixing the Installation Plate Drilling the Hole 1. Install the installation plate horizontally over the structural parts on the wall using the spaces indicated on the plate, as shown 2. In the case of tiled, concrete or diameter holes. Place anchorage supports for ...

Connective pipe and drainage installation Drainage 1. Run the drain hose sloping downward. Do not install the drain 2. When connecting extension drain hose, insulate the connecting part of extension drain hose with a shield pipe, do not let the drain hose slack. Connective pipe 1. For the left-hand ...

Attention Piping and wrapping 1. Bundle the tubing, connecting cable, and drain hose with tape 2. Because the condensed water from rear of the indoor unit is gathered in ponding box and is anything else in the box. 1. Connect the indoor unit first, then the outdoor unit.2. Do not allow the piping to...

1. Install the outdoor part of the unit on a rigid surface to avoid excess noise and vibration. 2. Direct the air vent toward an area without obstacles. especially in areas where it is frequently windy. 4. If the installation site is exposed to heavy winds, such as in coastal areas, place the unit a...

Settlement of outdoor unitAnchor the outdoor unit tightly and horizontally on a concrete or rigid Air inlet Air inlet Air outlet $ % mount with a bolt and nut 0.39" or A ft) B( ft) Outdoor unit dimension ft(WxHxD) [[ [[ ' [[ 1 ' 0.32" diameter (Purchased separately). Chassis Drainconnection ...

Flaring work Main cause for refrigerant leakage is due to defect in the flaring work. Carry out correct flaring work using the following procedure: 1. Cut the pipes and the cable.A) Use the piping kit accessory or pipes purchased locally. B) Measure the distance between the indoor and the outdoor un...

4. Flaring work. die in the dimension shown in the table below. OUTER Connection Adjustment 1. Align the pipes to be connected. OUTER TIGHTENING Caution: Excessive twisting may break the nut, depending on the installation conditions. Refrigerant piping connection Bar pipe Handle Clamphandle Yoke Red...

1. The inside and outside connecting cable can be connected without removing the front grille. 2. Connecting cable between indoor unit and outdoor unit shall be approved polychloroprene sheathed flexible cord, type cord. 3. Lift the indoor unit panel up, remove the electrical box cover by loosening ...

1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of wiring, be guided by the circuit diagram posted on the inside of control cover. liable to come loose from vibrations to which the unit is subjected during the course of transportation. Check ...

Air purging with vacuum pump 1. Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have been properly connected and all wiring for the test run has been completed. Remove the service valve caps from both the gas and the liquid side on the outdoor unit. Note tha...

Air purging 24 Vacuum pump Charge hose Manifold valve -76cm/Hg Chargehose Handle Lo Handle Hi Outdoor unit Indoor unit When using the vacuum pump For method of u s ing a manifold valve, refer to it s operation manual. manifold valve. evacuate. After s tarting evacuation, s lightly loo s e the flare ...

Electrical safety Perform the electric safe ty check after completing installation: Gas leak check Soap water method Apply a soap water or a liquid neutral detergent on the indoor unit connection or outdoor unit connections by a soft brush to check for leakage of the connecting points of th e piping...

Test running Perform test operation after completing gas leak check at the flare nutconnections and electrical safety check. 1. Connect the power, press the ON/OFF button on the remote controller to turn the unit on. cannot be controlled by the remote controller to run in cooling mode, manual operat...

1. Contact a specialist to install the device.2. Guarantee that the unit is appropriately fastened and complies with all of the aforementioned safety norms.3. Before operating the air conditioner, ensure that the air filter is installed correctly.4. If the unit has been out of use for a long period ...