Friedrich EQ08M11 - Manuals

PROPERTY DAMAGE HAZARDS FIRE DAMAGE HAZARDS: • Read the Installation/Operation Manual for this air conditioning unit prior to operating. • Use air conditioner on a single dedicated circuit within the specifi ed amperage rating. • Connect to a properly grounded outlet only. • Do not remove ground pro...

Serial Number Decade Manufactured L=0 C=3 F=6 J=9 A=1 D=4 G=7 B=2 E=5 H=8 A A A Y 00001 Production Run Number Year Manufactured A=1 D=4 G=7 K=0 B=2 E=5 H=8 C=3 F=6 J=9 Product Line X-Start Month Manufactured A=Jan D=Apr G=Jul K=Oct B=Feb E=May H=Aug L=Nov C=Mar F=Jun J=Sept M=Dec 1st Digit – Functio...

PERFORMANCE DATA * Installation Information / Sleeve Dimensions * Minimum extensions when mounted in a window.** Minimum widths achieved using one side cur tain assembly as opposed to both in a standard installation. Circuit Rating/ Breaker (B) (C) Front SIDE VIEW Model C ircuit Rating Breaker or T-...

ELECTRICAL DATA ELECTRIC SHOCK HAZARD WARNING Turn off electric power before service or installation. All electrical connections and wiring MUST be installed by a qualifi ed electrician and conform to the National Electrical Code and all local codes which have jurisdiction. Failure to do so can resu...

To start unit s i ti , e l c a t p e c e r r e p o r p a o t n i d e g g u l p d n a d e ll a t s n i s i r e n o it i d n o c ri a r u o y fI ready to go. The first time the unit is started, the compressor will delay for threeminutes. See Automatic Component Protection on the following page. 1 Touc...

To set the timer NOTE: You can set the START and STOP times a minimum of one hour apart, and a maximum of 23 hours apart. 9 TIMER START - Press Start . g n il o o c r o f e m it t r a t s t n e r r u c e h t w e i v o t Continue pressing the Start button until you arrive at the start time you desire...

MODE CONTROL The mode control pad(s) allow the selection of the operating modes of the unit. There is a two second delay before the mode activates its appropriate relay. OPERATING SEQUENCE / CHARACTERISTICS AND FEATURESCompressor Operation The run state of the compressor is determined by the differe...

MECHANICAL COMPONENTS Plenum assembly Diffuser with directional louvers used to direct the conditioned air fl ow. Blower wheel Attaches to the indoor side of the fan motor shaft and is used for distributing unconditioned, room side air though the heat exchanger and delivering conditioned air into th...

13 TESTING THE ELECTRONIC CONTROL BOARDS FOR XQ MODELS Activating Test Mode: Activate test mode by pressing at the same time the “MODE” button and the “TEMP ” button on XQ models . LEDs for Hour, Start, and Stop will blink 1 bps while Test Mode is active. Test Mode has duration of 90 minutes. Test M...

TEST: 1. Remove leads from thermostat. 2. Tu r n t h e r m o s t a t k n o b c l o c k w i s e t o i t s c o l d e s t position. 3. Test for continuity between the two terminals. Contacts should be closed. 4. Turn thermostat knob counterclockwise to its warmest position. 5. Test for continuity - con...

CAPACITORS ELECTRIC SHOCK HAZARD WARNING Turn off electric power before servicing. Discharge capacitor with a 20,000 Ohm 2 Watt resistor before handling. Failure to do so may result in personal injury, or death. Many motor capacitors are internally fused. Shorting the terminals will blow the fuse, r...

HEATING ELEMENT (See Figure) All electric heat models are equipped with a heating element. The EQ08 has a 1.15 KW element. The heating element contains a fuse link and a heater limit switch. The fuse link is in series with the power supply and will open and interrupt the power when the temperature r...

Suction Line Evaporator Coil Metering Device Refrigerant Strainer Discharge Line Condenser Coil Compressor Refrigerant Drier Liquid Line A good understanding of the basic operation of the refrigeration system is essential for the service technician. Without this understanding, accurate troubleshooti...

• R-410A pressure is approximately 60% higher than R-22 pressure. • R-410A cylinders must not be allowed to exceed 125 F, they may leak or rupture. • R-410A must never be pressurized with a mixture of air, it may become fl ammable. • Servicing equipment and components must be specifi cally designed ...

Proper refrigerant charge is essential to proper unit operation. Operating a unit with an improper refrigerant charge will result in reduced performance (capacity) and/or effi ciency. Accordingly, the use of proper charging methods during servicing will insure that the unit is functioning as designe...

3. Install a process tube to sealed system. 4. Make necessary repairs to system. 5. Evacuate system to 200 microns or less. 6. Weigh in refrigerant with the property quantity of R410-A refrigerant. 7. Start unit, and verify performance. 8. Crimp the process tube and solder the end shut. Proper safet...

Restricted Refrigerant System Troubleshooting a restricted refrigerant system can be diffi cult. The following procedures are the more common problems and solutions to these problems. There are two types of refrigerant restrictions: Partial restrictions and complete restrictions. A partial restricti...

Locked Rotor Voltage (L.R.V.) Test Locked rotor voltage (L.R.V.) is the actual voltage available at the compressor under a stalled condition. Single Phase Connections Disconnect power from unit. Using a voltmeter, attach one lead of the meter to the run “R” terminal on the compressor and the other l...

Single Phase Resistance Test Remove the leads from the compressor terminals and set the ohmmeter on the lowest scale (R x 1). Touch the leads of the ohmmeter from terminals common to start (“C” to “S”). Next, touch the leads of the ohmmeter from terminals common to run (“C” to “R”). Add values “C” t...

Recommended procedure for compressor replacement 1. Be certain to perform all necessary electrical and refrigeration tests to be sure the compressor is actually defective before replacing. 2. Recover all refrigerant from the system though the process tubes. PROPER HANDLING OF RECOVERED REFRIGERANT A...

1. 2. 3. 4. 5. ELECTRIC SHOCK HAZARD WARNING Turn off electric power before service or installation. Failure to do so may result in personal injury, or death. Sealed Refrigeration System contains refrigerant and oil under high pressure. Proper safety procedures must be followed, and proper protectiv...

ROUTINE MAINTENANCE AIR FILTER Clean the unit air intake fi lter at least every 300 to 350 hours of operation. Clean the fi lters with a mild detergent in warm water and allow to dry thoroughly before reinstalling. COILS AND BASE PAN The indoor coil (evaporator coil), the outdoor coil (condenser coi...

29 29 Due to variations in room design, climate zone and occupancy, larger areas may require the use of multiple units to provide the optimal cooling solution. This is a general guide. Please consult manual J or M for exact load calculations. 1. If heavily shaded, reduce capacity 10%. 2. If very sun...

Problem Possible Cause Possible Solution Unit does not operate. The unit is turned to the off position, Turn the unit to the on position and raise or lower temperature setting (as appropriate) to call for operation. The LCDI power cord is unplugged. Plug into a properly grounded 3 prong receptacle. ...

COOLING ONLY ROOM AIR CONDITIONERS: TROUBLESHOOTING TIPS n o i t c A e s u a C e l b i s s o P m e l b o r P Compressordoes not run Low voltage Check voltage at compressor. 115V & 230V units will operate at 10% voltage variance T-stat not set cold enough or inoperative or electronic controlboard...

HEAT / COOL ONLY ROOM AIR CONDITIONERS: TROUBLESHOOTING TIPS n o i t c A e s u a C e l b i s s o P m e l b o r P Room temperature uneven (Heating cycle) Heat anticipator (resistor) shorted (on applicable models) Disconnect power to unit. Remove resistor from t-stat bulb block. Plug in unit & all...

37 ELECTRONIC CONTROL COOL ONLY MODELS: XQ05M10 * XQ06M10 * XQ08M10 * XQ10M10 * * Last character may vary.

4 INSTRUCTIONS FOR USING COOLING LOAD ESTIMATE FORM FOR ROOM AIR CONDITIONERS (AHAM PUB. NO. RAC-1) A. This cooling load estimate form is suitable for estimating the cooling load for comfort air conditioning installations which do not require specifi c conditions of inside temperature and humidity. ...

5 COOLING LOAD ESTIMATE FORM HEAT GAIN FROM 1. WINDOWS: Heat gain from the sun. Northeast East Southeast South Southwest West Northwest North 2. WINDOWS: Heat by conduction (Total of all windows.) Single glass Double glass or glass block 3. WALLS: (Based on linear feet of wall) a. Outside walls Nort...

6 Following is an example using the heat load form: A space to be conditioned is part of a house geographically located in an area where the lowest outdoor ambient winter temperature is 40°F. The calculated heat loss is 184 BTU/Hr./°F. Subtract 40°F (lowest outdoor ambient temperature for the geogra...

7 HEATING LOAD FORM FRIEDRICH ROOM UNIT HEAT PUMPS BTU/HR PER WALLS: (Linear Feet) °F TEMP. DIFFERENCE 2” Insulation Lin. Ft. x 1.6 Average Lin. Ft. x 2.6 WINDOWS & DOORS (Area, sq. ft.) Single Glass: Sq. Ft. x 1.13 Double Glass: Sq. Ft. x 0.61 INFILTRATION - WINDOWS & DOORS: AVG. Lin. Ft. x...

43 Friedrich Air Conditioning Company 10001 Reunion Place, Suite 500 San Antonio, TX 78216 1-800-541-6645 www.friedrich.com ROOM AIR CONDITIONERS LIMITED WARRANTY FIRST YEAR ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from dat...

TECHNICAL SUPPORT CONTACT INFORMATION 44 FRIEDRICH AIR CONDITIONING CO. 10001 Reunion Place, Ste. 500, San Antonio, TX 78216(210) 546-0500 877-599-5665 x 261 FAX (210) 546-0731 Email: [email protected] Printed in the U.S.A.