Ford 2013 Expedition v.2- Manuals

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only), the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”), only to help provide you with the directions...

REPLACEMENT PARTS RECOMMENDATION Your vehicle has been built to the highest standards using quality parts.We recommend that you demand the use of genuine Ford and Motorcraftparts whenever your vehicle requires scheduled maintenance or repair.You can clearly identify genuine Ford and Motorcraft parts...

WARNING: Please read the Supplementary Restraints System chapter. Failure to follow the specific warnings and instructions could result in personal injury. WARNING: Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag. Using your vehicle ...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

WARNING: Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a crash or sudden stop, which may increase the risk of serious injury. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduc...

BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a crash. Use a belt-positioning booster seat for children who have o...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

This is necessary to remove the remaining slack that will exist once theextra weight of the child is added to the child restraint. It also helps toachieve the proper snugness of the child seat to your vehicle.Sometimes, a slight lean toward the buckle will additionally help toremove remaining slack ...

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol. The LATCH anchors are located at the rear section of the rear seatbetween the cushion and seatback, below the locator symbols on the seatback. Follow the child seat manufacture...

The tether strap anchors in your vehicle are in the following positions(shown from top view). • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct te...

2. Locate the correct anchor for the selected seating position. • Second row outboard seatingpositions • Second row center seatingposition (if equipped) 3. Grasp the tether strap andposition it to the seat frame. 32 Child Safety 2013 Expedition (exd) Owners Guide gf, 2nd Printing, October 2012USA (f...

4. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame. 5. Rotate the tether strap clip. 6. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row center seating position 1. Route the child safety seat tether strap over the back...

2. Locate the anchor webbing loop for the seating position. • You may need to pull back the top of the hinged panel along thebottom of the seat back to access the tether anchor. 3. Clip the tether strap through the anchor loop as shown. If the tetherstrap is clipped incorrectly, the child safety sea...

CHILD SAFETY LOCKS When these locks are set, the rear doors cannot be opened from theinside. The childproof locks are located onthe rear edge of each rear door andmust be set separately for eachdoor. Move the lock control up/down toengage/disengage the childprooflock. Child Safety 35 2013 Expedition...

PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while t...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue i...

Pregnant women should alwayswear their safety belts. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of the...

Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a ch...

SAFETY BELT HEIGHT ADJUSTMENT WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat beltand increase the risk of injury in a crash. Adjust the height of the s...

To adjust the comfort guide: 1. Slip the shoulder belt into thebelt guide (the portion of the beltbetween the latch tongue and theD-ring, not the portion where thebelt exits from the quarter trimpanel). 2. Slide the guide up or down along the webbing so that the belt iscentered on the occupant’s sho...

Deactivating and Activating the Belt-Minder® Feature WARNING: While the design allows you to deactivate your Belt-Minder®, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leavethe Belt-Minder® system activated for yourself and others...

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodicallyto make sure they work properly and are not damaged. Inspect thevehicle and child seat safety belts to make sure there are no nicks, tearsor cuts. Replace if necessary. All vehicle ...

The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and right frontpassenger from certain upper body injuries. Airbags do not inflate slowly;there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see...

• Restraint system warning light and backup tone. • The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety belt usage sensors, driver seat positionsensor, and indicator lights. How does the Restraint Safety System work? The Restraint Safety System can adapt th...

The driver and front passengerairbags will deploy during significantfrontal and near frontal crashes. The driver and passenger front airbag system consists of: • driver and passenger airbag modules • crash sensors and monitoring system with readinessindicator. See Crash Sensors and Airbag Indicator ...

WARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is notreplaced, the unrepaired area will increase the risk of injury in a crash. The side airbags are locate...

• a flexible headliner which opens above the side doors to allow aircurtain deployment. • crash sensors and monitoring system with readiness indicator.See Crash Sensors and Airbag Indicator in this chapter. Children 12 years old and under should always be properly restrained inthe rear seats. The Sa...

A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after theignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until...

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with IndustryCanada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference...

REMOTE CONTROL Integrated Keyhead Transmitters Your vehicle may be equipped withtwo integrated keyheadtransmitters. The key blade is usedto start the vehicle and unlock orlock the driver’s door from outsidethe vehicle. The transmitter portionfunctions as the remote control. Note: Your vehicle’s keys...

Car Finder Press the button twice within three seconds. The horn will soundand the turn signals will flash. We recommend you use thismethod to locate your vehicle, rather than using the panic alarm. Sounding a Panic Alarm Press the button to activate the alarm. Press the button againor switch the ig...

PRINCIPLES OF OPERATION MyKey® allows you to program keys with restricted driving modes topromote good driving habits. All but one of the keys programmed to thevehicle can be activated with these restricted modes. Any keys that havenot been programmed are referred to as an administrator key or admin...

• Audio system maximum volume of 45%. A message in the audiosystem is displayed when attempting to exceed the limited volume. • AdvanceTrac. The system cannot be turned off when Always-on hasbeen set. CREATING A MYKEY Use the information display controls to create a MyKey.1. Insert the key you want ...

In addition to the key that has been programmed as a MyKey, owners ofvehicles equipped with traditional keys have the option to program thenon-Ford-approved remote start system as a MyKey if the remote startfob is used by the MyKey driver. To program a non-Ford-approved remote start system as a MyKe...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock the vehicle. Power Door Locks The power door lock control is located on the driver and front passengerdoor panels. A. Unlock B. Lock Remote Control You can use the remote control anytime the vehicle...

Power Liftgate or Liftgate Window (If Equipped) WARNING: Make sure all persons are clear of the power liftgate area before using the control. WARNING: Make sure the power liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from f...

Autolock and Unlock The autolock feature will lock all the doors, the liftgate and the liftgatewindow when: • all doors are closed, • the ignition is on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). If the vehicle was autol...

Power Liftgate (If Equipped) WARNING: Make sure that the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive withthe liftgate door open, keep the vehicle well ventilated so outside aircomes int...

If the liftgate reverses and starts to close after a open request, a fastcontinuous chime indicates excessive load on the liftgate or a possiblestrut failure. If any excessive load is removed and you still have a fasterchime, have the system serviced immediately by your authorized dealer. Do not att...

To close with the rear cargo area button: WARNING: Keep clear of the liftgate when activating the rear switch. Note: The rear cargo area control button is disabled when the liftgate is latched. Press and release the control on theleft rear quarter panel. A chime willbeep once if conditions are notco...

Resetting the Power Liftgate If any of these conditions occur, the power liftgate may not operate andmust be reset: • A low voltage or dead battery • Disconnected battery • The liftgate is manually closed and left ajar (unlatched) To reset the power liftgate: 1. Disconnect the battery for 20 seconds...

SECURICODE™ KEYLESS ENTRY KEYPAD You can use the keyless entrykeypad to lock or unlock the doorsor release the liftgate glass withoutusing a key. The keypad can be operated with the factory-set 5-digit entry code; this code is located on the owner’swallet card in the glove box and is available from ...

Automatic Disarming Your vehicle disarms when you switch the ignition on with a coded key. Replacement Keys Note: Your vehicle may come equipped with two integrated keyhead transmitters. The integrated keyhead transmitter functions as a programmed ignitionkey that operates all the locks and starts t...

6. Turn the ignition off and remove the second previously programmedcoded key from the ignition. 7. After three seconds but within 20 seconds of turning the ignition offand removing the previously programmed coded key, insert the newunprogrammed key into the ignition. 8. Turn the ignition from off t...

Disarming the Alarm To disarm the alarm, do any of the following: • Press the power door unlock button within the 20-second pre-armedmode. • Press the unlock button on the remote control. • Unlock the doors with the keyless entry pad. • Turn the ignition on with a valid key. • Press the panic button...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. 1. Pull and hold the steering wheelrelease lever. 2. Adjust the steering wheel to thedesired position then release thelever. AUDIO CONTROL A. Media B. Volume up C. Volume down D. Seek down or previous...

VOICE CONTROL (IF EQUIPPED) A. Voice recognition B. Phone mode Press OK to confirm selection. See the SYNC or Navigation System chapter. CRUISE CONTROL See the Cruise Control chapter. B A + SET RES OFF ON Steering Wheel 81 2013 Expedition (exd) Owners Guide gf, 2nd Printing, October 2012USA (fus)

ADJUSTABLE PEDALS (IF EQUIPPED) WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press andhold the appropriate control to move the pedals. A. Closer B. Farther The pedal position...

WINDSHIELD WIPERS Note: Fully defrost the windshield before turning on the windshield wipers. Note: Make sure the windshield wipers are turned off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, ins...

LIGHTING CONTROL Rotate the control clockwise to thefirst position to turn on the parkinglamps. Rotate the control clockwise to thesecond position to turn on theheadlamps. Rotate the control to the verticalposition to turn the headlamps off. High Beams • Push the lever toward theinstrument panel to ...

AUTOLAMPS The autolamp system provides lightsensitive automatic on/off control ofthe exterior lights normallycontrolled by the headlamp control. The autolamp system also keeps thelights on for approximately20 seconds or, if equipped with amessage center, you can select adelay from 0–180 seconds afte...

DAYTIME RUNNING LAMPS (IF EQUIPPED) WARNING: Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lightingduring these conditions. Failure to activate your headlamps under thesecondit...

INTERIOR LAMPS Front Row Map Lamps (If Equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until the courtesylamps come on. • the remote entry controls are pressed and the i...

Rear Cargo Lamp The rear cargo lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is off(and switch is in the middleposition). With...

POWER WINDOWS WARNING: Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the ...

Window Lock A. Unlock B. Lock Press the control to lock or unlock the rear and front passenger windowcontrols. Accessory Delay You can use the window switches for several minutes after you switchthe ignition off, or until you open either front door. EXTERIOR MIRRORS Power Exterior Mirrors WARNING: D...

Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fullyengage the mirror in its support when returning it to its original position. Power-Folding Mirrors (If Equipped) Note: Activating the mirrors 10 or more times within one minute, or repeated folding and u...

Integrated Blind Spot Mirrors WARNING: Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upperoutboard corner of the exterior mirrors. They are designed to assist youby increasing visibility along the side of your vehicle...

INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors alsohave a second...

GAUGES Cluster shown in standard measure. Metric similar.A. TachometerB. Battery voltage gauge:C. Engine oil pressure gaugeD. SpeedometerE. Fuel gaugeF. Information display. See Information displays for more information. G. Engine coolant temperature gauge Battery Voltage Gauge Indicates the battery...

Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when theignition is on). The fuel gauge may vary slightly when the vehicle is inmotion or on a grade. The fuel icon and arrow indicates which side ofthe vehicle the fuel filler door is located. Information Display Odometer Lo...

Anti-Lock Braking System If it illuminates when you are driving, this indicates amalfunction. You will continue to have the normal brakingsystem (without ABS) unless the brake warning lamp is also illuminated. Have the system checked by your authorized dealer. Battery If it illuminates while driving...

Low Tire Pressure Warning It will illuminate when your tire pressure is low. If the lampremains on with the engine running or when driving, checkyour tire pressure as soon as possible. The lamp also illuminates momentarily when you switch the ignition onto confirm the lamp is functional. If it does ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Stability Control System Displays when the AdvanceTrac®/Traction control is active. Ifthe ligh...

GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of the ...

• MILES (km) TO E: This displays an estimate of approximately how faryou can drive with the fuel remaining in your tank under normaldriving conditions. Remember to turn the ignition off when refuelingto allow this feature to correctly detect the added fuel. Distance toempty is calculated using a run...

5. Press and hold to go up by one zone then release. Repeat this untilyou reach the desired zone. 6. Release the SELECT/RESET stem and allow the setup timer to expireto exit the procedure Compass calibration adjustment Note: For optimum calibration, drive to an open, level location away from large m...

Press and hold the SELECT/RESET stem to get into the setup menusequence for the following displays: SETUP HOLD RESETFOR SYSTEMCHECK press and holdtheSELECT/RESETstem OIL LIFE CHARGING SYSTEM WASHER FLUID LEVEL DOOR AJAR STATUS LIFTGATE/GLASS AJAR STATUS BRAKE SYSTEM MYKEY DISTANCE(if programmed) X M...

Information Display Controls (Type 2) • Press the INFO button to scrollthrough trip, fuel usage, andMyKey® information. • Press the SETUP button to scrollthrough various vehicle featuresettings. • Press the RESET button to choose settings, reset information andconfirm messages. Info Press the INFO b...

INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may beabbreviated or shortened depending upon which cluster type you have. Press the RESET button for Type 1 displays or the OK button for Ty...

MyKey® Messages Action / Description VEHICLE SPEED80 MPH MAX Displayed when a MyKey® is in use and theAdmin has enabled the MyKey speed limit andthe vehicle speed is 80 mph (130 km/h). CHECK SPEEDDRIVE SAFELY Displayed when a MyKey® is in use and theoptional setting is on and the vehicle exceedsa pr...

GENERAL INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio reception...

MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracksand folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 trackmode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the ...

REAR AUDIO CONTROLS Your vehicle is equipped with rear seat audio controls. This allows frontand middle seat passengers to listen to different media sources (radio,CD, SYNC or DVD) simultaneously. Note: The front and middle seat passengers cannot listen to two different radio stations at the same ti...

Switching Dual Play Mode On You can switch Dual Play mode on by simultaneously pressing the 2 and4 memory preset buttons on the audio or by doing the following:1. Press the headphone/speaker control. The headphone icon illuminates in both front and rear audio displays indicating the rearseat speaker...

AUXILIARY INPUT JACK WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommen...

6. Press AUX until LINE or LINE IN appears in the display. You should hear music from your device even if it is low. 7. Adjust the volume on your portable music player until it reaches the volume level of the FM station or CD. Do this by switching back andforth between the AUX and FM or CD controls....

Satellite Radio Reception Factors Potential satellite radio reception issues Antennaobstructions For optimal reception performance, keep theantenna clear of snow and ice build-up andkeep luggage and other material as far awayfrom the antenna as possible. Terrain Hills, mountains, tall buildings, bri...

Wireless Headphones This unit includes a built-in dual channel infrared transmitter for usewith your wireless headphones. You can change the volume with thecontrols on each headset. You must use the wireless headphones within aline of sight from the transmitter. Infrared transmission, like visible l...

F. Headphone jack: Plug in your wired headphones with a 1/8-inch (3.5 millimeter) stereo connector plug to listen to audio from the program. G. Video input jack (red): Connect an RCA cable to this port. H. Video input jack (white): Connect an RCA cable to this port. I. Video input jack (yellow): Con...

Note: Do not mix old and new batteries. Mixing old and new batteries can shorten battery life and cause chemical leaks from the old batteries. Note: Keep the batteries out of the reach of children. If someone swallows a battery, immediately consult a doctor. When you dispose ofused batteries, keep t...

6. MUTE: Press this button to turn off the sound sent to the headphones. The screen displays that the sound is muted. Pressing the button againrestores sound to the previously set level. This feature is onlyfunctional in DVD mode. 7. MENU: Press this button to go to the disc’s root menu. 8. CH + and...

3. When the device is on and is displaying a picture, pivot the screen to change the viewing angle to optimize the picture quality. 4. Remember to turn the device off and pivot the LCD panel to the locked position when not in use. DVD Basics To get the most use out of each DVD, make sure you read th...

• Before playing a disc, clean it with a commercially available cleaningcloth. Wipe each disc from the center out. Do not use solvents such asbenzene, thinner, commercially available cleaners, or antistatic sprayintended for analog discs. • Do not use any irregularly shaped discs. If you insert an i...

The Speaker Setup menu has the following options: • LT/RT • Stereo • V SURR • OFF The Dolby Digital Setup menu has the following options: • Stereo • L-Mono • R-Mono • Mix-Mono Quality Setup Press SETUP on the remote control, and then use CH +, CH -, VOL + and VOL - to navigate the Setup Page. Press ...

Subtitle This allows the user to turn the subtitles on and off in the selectedlanguage for playback automatically. Disc Menu This allows the user to control the DVD disc menu in the selectedlanguage. Parental This section of the Setup Menu allows user to control the content ofmovie playback from G t...

Playing an Audio CD When playing an audio CD, the DISPLAY banner appears automatically. Itdisplays the current track and the amount of time the track has beenplaying, the total amount of time on the disc and the current timerunning on the disc. Press DISPLAY on the remote control to see the DISPLAY ...

Selecting a Play Mode You can choose what order the songs play on a disc temporarily. TheFOLDER play mode is the default. To access the play mode operations,press REPEAT on the remote control. The play mode options are: • Single: Play a selected song. • Repeat One: Repeat the song that is playing. •...

Connecting an MP3 Device Using a USB Cable Plug the MP3 Dock Connector to USB cable into a high-power USB porton your DVD-headrest module, and then connect the other end to theplayer. See the documentation that came with your device for more information. Charging the MP3 Player Battery After you tur...

Compliance Information FCC Notice This device has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference in a residential installation. This device genera...

Warranty INVISION Automotive Systems Inc., (the “Company”) warrants to theoriginal retail purchaser of this product, when purchased from aparticipating new car dealership, that should this product under normaluse and conditions, be proven defective in material or workmanship,such defect(s) will be r...

MANUAL HEATING AND AIR CONDITIONING SYSTEM WITHOUTAUXILIARY CLIMATE CONTROL A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Temperature control: Controls the tempe...

Distributes air through the floor vents. Distributes air through the windshield defroster vents, demistervents and floor vents. Distributes air through the windshield defroster vents anddemister vents. This setting can also be used to defog and clearthe windshield of a thin covering of ice. D. Auxil...

When this button is pressed, the display only shows the rear temperaturesetting. After the rear setting changes are completed on the frontcontrol, the display automatically shows both climate settings. F. Passenger temperature control: Press and turn to increase or decrease the air temperature on th...

different from the front temperature when more than one reartemperature bar is lit.When this button is pressed, the display only shows the rear temperaturesetting. After the rear setting changes are completed on the frontcontrol, the display automatically shows both climate settings. G. Passenger te...

Distributes air through the windshield defroster vents anddemister vents. This setting can also be used to defog and clearthe windshield of a thin covering of ice. N. Driver heated seat control: Press to switch the driver heated seat off and on. See Heated seats in the Seats chapter for more informa...

GENERAL OPERATING TIPS Manual Heating and Air Conditioning System • To reduce fog build-up on the windshield during humid weather,select Defrost. Temperature and fan speed can also be increased toimprove clearing. • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or w...

Dual Automatic Temperature Control System • To reduce fog build-up on the windshield during humid weather,select Defrost. Temperature and fan speed can also be increased toimprove clearing. • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with recirculated air eng...

HEATED WINDOWS AND MIRRORS (IF EQUIPPED) Heated Rear Window Note: The vehicle must be running to use this feature. Press the control to clear the rear window of thin ice and fog. Press thecontrol again within 15 minutes to switch it off. It turns off automaticallyafter approximately 15 minutes, or w...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the passenger sensing system, resulting in serious injury ordeath in a crash. Always sit upright against your seat back, with yourfe...

Adjusting the Head Restraint Raise: Pull up the head restraint. Lower: 1. Press and hold button C. 2. Push down on the head restraint. Remove: 1. Pull up the head restraint until it reaches the highest adjustmentposition. 2. Press and hold buttons C and D. 3. Pull up the head restraint. Reinstall Al...

Power Lumbar (If Equipped) The control is located on theoutboard side of the seat. Press theforward or rearward side of thecontrol for more or less support. MEMORY FUNCTION (IF EQUIPPED) This feature will save and recall the positions of the driver seat, powermirrors and adjustable pedals. The memor...

Heated and Cooled Seats Air Filter Replacement (If Equipped) The heated and cooled seat system includes air filters that must bereplaced periodically. See scheduled maintenance information for more information. There is a filter located under each front seat. The filter can be accessedfrom the secon...

REAR SEATS Folding Down the 2nd Row 40% Seat System WARNING: Use caution when folding the seat back to the flat back position as the system will move forward when you lift the release handle. WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are no...

2. Locate handle on the side of theseat cushion by the door. 3. Pull up on the handle and pushthe seat back forward toward thefront of the vehicle. To return the seat to the upright position: 1. Lift the seat back toward the rearof the vehicle. 2. Rotate the seat back until youhear a click, locking ...

Placing the 2nd Row Outboard 40% Seats in Cargo Mode WARNING: Use caution when folding the seat back to the flat back position as the system will move forward when you lift the release handle. WARNING: Always return the seat from the kneel position prior to raising the seat back. Failure to do so co...

Adjusting the 2nd Row Outboard 40% Seat for E-Z Entry WARNING: Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. WARNING: After using the E-Z Entry feature make sure there are not any objects, cargo or t...

To return the seat to a seating position: 1. Push the seat down and latch tothe floor. 2. Bring the seat back to an uprightposition. The seat back should lockinto position. Note : If the seat back will not return to the upright position, tumble the seat again and re-latch it to the floor. Be sure th...

Reclining the Second-Row Outboard 40% Seat Back WARNING: Reclining the seat back can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a crash. Locate the release handle on theoutboard side of the seat cushion.Lift to allow the seat back t...

2. With the latch released the seatback can be lowered into the loadfloor position. 3. To return the seat to the uprightposition, lift the seat back until thelatch is fully engaged. Adjusting the Second-Row Center 20% Seat (If Equipped) Note: This seat can be moved forward to keep a child in a child...

Rear Heated Seats (If Equipped) WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions,must exercise care when using the seat heater. The seat heater maycause b...

Folding Down the Third Row Seats to the Load Floor WARNING: To prevent possible damage to the seat or safety belts, make sure that the safety belts are not buckled when moving the seat to the load floor position. WARNING: Before returning the seat back to its original position, make sure that cargo ...

UNIVERSAL GARAGE DOOR OPENER The appearance of your vehicle’s universal garage door opener will varyaccording to your option package. Before programing, make sure youidentify which transmitter you have by comparing it to the graphicsbelow. HomeLink® Car2U® Home AutomationSystem Note: The programming...

Rolling Code Programming Note: If you do not follow the time-sensitive instructions, the device will time out and you will have to repeat the complete procedure. Note: It may be helpful to have another person assist you in programming the transmitter. 1. Switch the ignition on. 2. Press and hold the...

8. The LED lamp will begin to flash rapidly until programming iscomplete. If your garage door does not operate, repeat the previoussteps. Otherwise, call the toll-free help line at 1-866-572-2728. The LED lamp above the selected button will illuminate to confirm thatthe system is responding to the b...

Erasing the Function Button Codes Note: You cannot erase individual buttons. 1. Press and hold the outer two functionbuttons simultaneously for approximately20 seconds until the indicator lights abovethe buttons flash rapidly. 2. When the indicator lights flash, releasethe buttons. The codes for all...

AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fireor serious injury. Note: If used when the engine is not running, the battery w...

CENTER CONSOLE (IF EQUIPPED) Stow items in the cupholder carefully as items may become loose duringhard braking, acceleration or collisions, including hot drinks which mayspill. Available console features include: A. Cupholders B. Utility compartment, coin holderslots, tissue box holder, audio input...

GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover. The emission system heats up th...

A. Off: The ignition is off. B. Accessory: Allows the electrical accessories, such as the radio, to operate while the engine is not running. C. On: All the electrical circuits are operational. Warning lights are illuminated. This is the key position when driving. D. Start: Cranks the engine. Release...

The heater acts as a starting aid by warming the engine coolant. This allowsthe climate control system to respond quickly. The equipment includes aheater element (installed in the engine block) and a wire harness. You canconnect the system to a grounded 120 volt A/C electrical source. We recommend t...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fue...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

It is best not to alternate repeatedly between gasoline and E85. If you doswitch fuels, it is recommended that you add as much fuel aspossible—at least half a tank. Do not add less than five gallons(18.9 liters) when refueling. You should drive the vehicle immediatelyafter refueling for at least 5 m...

Refilling With a Portable Fuel Container WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel® system. This could damage the fuel system and its seal, and may cause fuel to run onto theground instead of filling the tank, which could result in seriou...

5. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about ten seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. 6. Reinstall the plug (if equipped) into the fuel fill i...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: Do not use the Tow/Haul feature when driving in icy or slippery conditions as the ...

3. Remove the access plug on top ofthe steering column. 4. Using a flat-head screwdriver orsimilar tool, move the brake-shiftinterlock actuator spindle towardthe left, apply the brake, place thekey in the on position and shift thetransmission into N (Neutral). 5. Start the vehicle. 6. Reinstall the ...

USING FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED ) WARNING: For important information regarding safe operation of this type of vehicle, see General Information in the Wheels and Tires chapter. Note: Do not use 4X4 mode on dry, hard surfaced roads. Doing so will produce excessive noise, increase tire wear a...

4WD switch positions WARNING: Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorilyunder off-road conditions. Avoid sharp turns or abrupt maneuvers inthese vehicles. Note: If...

• 4L (4X4 LOW) provides electronically locked four-wheel drive when extra power at reduced speeds is required. The message center willdisplay 4X4 LOW when this mode is selected. This mode is notrecommended for use on dry pavement. Use this mode for off-roadlow-speed operation or when extra power is ...

How Your Vehicle Differs From Other Vehicles WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drivevehicles are not designed for cornering at speeds as high as passe...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn out and should be inspected by an authorized dealer. If yourvehicle has continuous vibration or shudder in the steering wheel while...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel and tire size may change the handlingcharacteristics of the vehicle and may adversely affect the performanceof the AdvanceTrac® system. In ...

A Vehicle without AdvanceTrac® with RSC® skidding off its intendedroute. B Vehicle with AdvanceTrac® with RSC® maintaining control on aslippery surface. USING ADVANCETRAC® WITH RSC® (IF EQUIPPED) The system automatically activates when you start your engine. TheAdvanceTrac® with RSC® system cannot b...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

Using the Front and Rear Sensing System Rear Sensing System The rear sensors are only active when the transmission is in R (Reverse).As the vehicle moves closer to the obstacle, the rate of the audiblewarning increases. When the obstacle is fewer than 10 inches (25centimeters) away, the warning soun...

Front Sensing System The front sensors are active when the gearshift is in any position otherthan P (Park) or N (Neutral) and the vehicle speed is below 8 mph(13 km/h). A. Coverage area of up to 27 inches(70 centimeters) from the front ofthe vehicle and about 6–9 inches(15–23 centimeters) to the sid...

Using the Rear View Camera System The rear view camera system displays what is behind your vehicle whenyou place the transmission in R (Reverse). The system uses two types ofguides to help you see what is behind your vehicle: 1. Fixed guidelines: Show the actual path the vehicle is moving in while r...

Guidelines and the Centerline Note: Fixed guidelines are only available when the transmission is in R (Reverse). Note: The centerline is only available if fixed guidelines are on. A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Yellow zone D. Fixed guideline: Green zone E. Centerline...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your footon the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved. Note: Vehicle speed may vary momentarily when driving up...

STEERING Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to decrease the driver’s effort in steering the vehicle. To help prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme leftfor more than a few sec...

ROOF RACKS AND LOAD CARRIERS WARNING: When loading the roof rail crossbars, it is recommended to evenly distribute the load, as well as maintain a low center of gravity. Loaded vehicles, with higher centers of gravity,may handle differently than unloaded vehicles. Extra precautions, suchas slower sp...

LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehic...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. 248 Load Carrying 20...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with ahigher limit than the original tires do not increase the GVWR andGAWR limitations. WARNING: Exceeding any vehicle ...

To move the shelf to the dividerposition: Pull up and pivot the shelf over the channels on the sidetrim panels and snap vertically inplace. POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) WARNING: In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy. Be sure t...

The running boards automaticallymove when the doors are opened toassist entering and exiting thevehicle. Automatic Power Deploy The running boards will extend down and out when the doors areopened. Automatic Power Stow The running boards will return to the stowed position after a two seconddelay whe...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle ...

TRAILER SWAY CONTROL Note: This feature does not prevent trailer sway, but reduces it once it begins. Note: This feature cannot stop all trailers from swaying. Note: In some cases, if vehicle speed is too high, the system may turn on multiple times, gradually reducing vehicle speed. This feature app...

Vehicle type Towing package Maximum GCWR - lb. (kg) Two–wheel drive (exceptEL and Max) Standard 11800 (5352) Two–wheel drive EL (U.S.)Two–wheel drive Max(Canada)Four–wheel drive (exceptEL and Max) 12100 (5488) Four–wheel drive EL (U.S.)Four–wheel drive Max(Canada) 12300 (5579) Two–wheel drive (excep...

Hitches WARNING: The trailer hitch on this vehicle is part of the vehicle rear crash safety structure. Do not remove the trailer hitch. Failure to follow this warning could compromise vehicle crash structureand increase the risk of injury in a rear end crash. Do not use a hitch that clamps onto your...

When hooking-up a trailer using a weight-distributing hitch, always usethe following procedure:1. Park your vehicle, without the trailer, on a level surface.2. Measure the height of the top of your vehicle’s front wheel opening on the fender. This is H1. 3. Attach the trailer to your vehicle without...

8. With the ignition on and all doors closed, let your vehicle (now with trailer and weight distributing bars connected) sit for a few minutesto let the air suspension re-settle. 9. Re-measure the height of the top of the front wheel opening, repeating Steps 7-9 as necessary to obtain a fender heigh...

Integrated Trailer Brake Controller (If Equipped) WARNING: The Ford TBC has been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and some electric-over-hydraulic (EOH) brakes. It will notactivate hydraulic surge-style trailer brakes. It is the respons...

The controller shows gain setting, output bar graph, and trailerconnectivity status in the information display. They appear in theinformation display as follows: • TBC GAIN = XX.X NO TRAILER: Shows the current gain setting during a given ignition cycle and when adjusting the gain. This alsodisplays ...

The gain should be set to provide the maximum trailer braking assistancewhile making sure the trailer wheels do not lock when using the brakes.Locked trailer wheels may lead to trailer instability.1. Make sure the trailer brakes are in good working condition, functioning normally and properly adjust...

Trailer Lamps WARNING: Never connect any trailer lamp wiring to the vehicle’s tail lamp wiring; this may damage the electrical system resulting in a fire. Contact an authorized dealer as soon as possible forassistance in proper trailer tow wiring installation. Additional electricalequipment may be r...

• If you are towing a trailer frequently in hot weather, hilly conditions,at the gross combined weight rating (or any combination of thesefactors), consider refilling your rear axle with synthetic gear lubricant(if the axle is not already filled with it). See the Capacities and Specifications chapte...

WRECKER TOWING Note: Vehicles equipped with air suspension must turn off the air suspension control and ignition switch before towing. See Air suspension in the Driving Aids chapter. If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside as...

TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing If your vehicle becomes inoperable (without access to wheel dollies,car-hauling trailer, or flatbed transport vehicle), it can be flat-towed (allwheels on the ground, regardless of the powertrain and transmissionconfiguration) under the following co...

BREAKING-IN You need to break in new tires for approximately 300 miles(480 kilometers). During this time, your vehicle may exhibit some uniquedriving characteristics. Avoid driving too fast during the first 1000 mi(1600 kilometers). Vary your speed frequently and change up throughthe gears early. Do...

• Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors,rollbars or light bars, running boards, ski racks). • Drive...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair s...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24 hours ...

If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56 kilometers). To obtain reimbursementinformation, U.S. Ford vehicle customers call 1-800-241-3673. Customerswill be asked to submit the...

Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake...

Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns,...

UTILIZING THE MEDIATION or ARBITRATION PROGRAM(CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers. Inthose cases, where you continue to feel that the efforts by Ford ofCanada and the authorized dealer to resolve a factory-related vehicleservice concern have been unsatisf...

CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in the vehicleare not working, a fuse may haveblown. Blown fuses are identifi...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Fuse or relay location Fuse amp rating Protected circuits 82 — Not used 83 — Not used 84 — Not used 85 — Wiper motor relay * Mini Fuses ** Cartridge Fuses Passenger Compartment Fuse Panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accesst...

GENERAL INFORMATION WARNING: Turn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object under the vehicle. Never place your hand between the extendedrunning board and the vehicle. A moving running board may causeinjury. Have your vehicle serviced ...

Working with the Engine Off 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key (if equipped). 3. Block the wheels. Working with the Engine On WARNING: To reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner ...

UNDER HOOD OVERVIEW 5.4L V8 A. Windshield washer fluid reservoir B. Engine oil dipstick C. Brake fluid reservoir D. Engine coolant reservoir E. Air filter assembly F. Power steering fluid reservoir G. Power distribution box H. Engine oil filler cap I. Battery A B C D E F G H I Maintenance 297 2013 E...

Adding Engine Oil Note: Do not remove the engine oil level dipstick or the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by theAmerican Petroleum Instit...

Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from yourdealer. Ford does not recommend the use of hydrometers or coolant teststrips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable;...

• In case of emergency, a large amount of water without engine coolantmay be added in order to reach a vehicle service location. In thisinstance, the cooling system must be drained, chemically cleaned withMotorcraft® Premium Cooling System Flush, and refilled withprediluted engine coolant as soon as...

If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease thecoolant concentration to 40%. • A coolant concentration of 40% will provide improved overheatprotection. Engine coolant concentrations below 40% will decrease thecorrosion/freeze protection cha...

When Fail-Safe Mode is Activated WARNING: Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.When in fail-safe mode, the vehicle will have limited power, will no...

BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normaloperating range; there is no need to add fluid. If the fluid levels are outsideof the normal operating range, the performance of the system could becompromised; seek service from your authorized dealer immediately. POW...

State or local regulations on volatile organic compounds may restrict theuse of methanol, a common windshield washer antifreeze additive.Washer fluids containing non-methanol antifreeze agents should be usedonly if they provide cold weather protection without damaging thevehicle’s paint finish, wipe...

CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the bladeto check for roughness. Clean the wiper blades with washer fluid or waterapplied with a soft sponge or cloth. CHANGING THE WIPER BLADES Replace wiper blades at least once per year for optimum performance. To replace the ...

2. Grasp the wiper blade and rotateit away from the wiper arm usingmoderate force until it disengagesfrom the wiper arm. 3. Once the wiper blade is loose,slide it away from the wiper arm. 4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly pr...

Changing the Air Filter Element 1. Locate the mass air flow sensorelectrical connector on the airoutlet tube. This connector willneed to be unplugged. 2. Unlock the locking clip on theconnector (connector shown frombelow for clarity), then squeeze andpull the connector off of the airoutlet tube. 3. ...

ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident, the alignment of your headlampsshould be checked by your authorized dealer. Vertical Aim Adjustment Before aim adjustment, disable the air suspension system. Refer ...

5. Locate the vertical adjuster oneach headlamp, then use a Phillips#2 screwdriver to turn the adjustereither counterclockwise orclockwise in order to adjust thevertical aim of the headlamp. Theupper edge of the light patternshould line up to the horizontal line. 6. Repeat Steps 3–5 for the otherhea...

Replacing Headlamp Bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause thebulb to break the next time the headlamps are operated. 1. Make sure that the headlam...

Replacing Tail, Stop, Turn Signal, Side Marker, and Backup LampBulbs The tail, stop, turn signal, side marker, and backup lamp bulbs arelocated in the same portion of the tail lamp assembly, one just below theother. Follow the same steps to replace any bulb: 1. Make sure the headlamp switch isin the...

Replacing License Plate Lamp Bulbs The license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch isin the off position. 2. Remove the license lamp screwfrom the assembly. 3. Pull the lamp down and twist t...

WAXING • Wash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The pain...

For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft® Professional StrengthCarpet & Upholstery Cleaner. • If grease or tar is present on the material, spot-clean the ...

CLEANING LEATHER SEATS(IF EQUIPPED WITH THE KING RANCH® EDITION) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will main...

• Rub the conditioner into leather until it disappears. Allow theconditioner to dry and repeat the process for the entire interior. If afilm appears, wipe off film with a dry, clean cloth. CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. ...

Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging thebattery, it may be advisable to disconnect the battery cables to ensurebattery charge is maintained for quick starting. Note: If battery cables are disconnected, i...

GENERAL INFORMATION Notice to Utility Vehicle, Van and Truck Owners WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or death from a rollover or other crash you must: • Avoid sharp turns and abrupt maneuvers; • Dri...

How Your Vehicle Differs from Other Vehicles Sport-utility vehicles, vans andtrucks can differ from some othervehicles in a few noticeable ways.Your vehicle may be: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbod...

Traction AA A B C Note: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering,hydroplaning or peak traction characteristics. The traction grades, from highest to lowest are AA, A, B, and C. The gradesrepresent the tir...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identifi...

E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires. These differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can becarried by the tire. This pressure is normally higher than themanufacturer’s recommended cold inflation pressure, which can be foundon the Safety Compliance Certificatio...

(4.15 bar). For full-size and dissimilar spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at the higher of the front and rear inflation pressure as shownon the Tire Label. 6. Visually inspect the tires to make sure there are no nails or otherobjec...

Damage Periodically inspect the tire treads and sidewalls for damage (such asbulges in the tread or sidewalls, cracks in the tread groove andseparation in the tread or sidewall). If damage is observed or suspected,have the tire inspected by a tire professional. Tires can be damagedduring off-road us...

Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originallyprovided by Ford. The recommended tire and wheel size may be found oneither t...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. The two front tires or two rear tires should generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in af...

Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you are driving, the wheels maybe out of alignment. Have an authorized dealer check the wheelali...

USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performanceof your vehicle, which could result in an increased risk of loss of vehiclecontrol, vehicl...

TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge.See Inflating Your Tires in this chapter. Failure to properly maintain your tir...

telltale after replacing one or more tires or wheels on your vehicle toensure that the replacement or alternate tires and wheels allow theTPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. See the following chart forinformation concerning your ...

Low tirepressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Repair the damaged road wheel and tire and reinstall it on the vehicle torestore system function. For adescription on how the systemfunctions, see When your temporary spare tire is installed...

CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However, if you must use a sealant, the tire pressure monitoring system sensor andvalve stem on the wheel must be replaced by an authorized Ford dealer. WARNING: See Tire P...

• Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly,additional caution should be given to: • towing a trailer. • driving...

Removing the spare tire 1. Remove the jack handle andwinch extension from the tray andassemble them. 2. Open the spare tire winch accessplug in the bottom of thecompartment for the jack and toolstray. 3. Insert the winch extension toolassembly through the access hole inthe floor and engage the winch...

6. Reinstall the jack bag properly around the jack and tool assembly tray,making sure the strap is securely fastened. 7. Close the access hole with the rubber plug. 8. Reinstall the tray into the vehicle and secure it with the wing nut(turn clockwise until tight). TECHNICAL SPECIFICATIONS Wheel Lug ...

VEHICLE IDENTIFICATION NUMBER The vehicle identification number islocated on the driver’s sideinstrument panel. Please note that in the graphic,XXXX is representative of yourvehicle identification number. The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacture...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through yourlocal Ford or Ford of Canada dealer. Ford Motor Comp...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • r...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of your vehicle when you sell ortrade it. Keep all receipts for c...

Protecting Your Investment Maintenance is an investment that will pay dividends in the form ofimproved reliability, durability and resale value. To maintain the properperformance of your vehicle and its emission control systems, it isimperative that scheduled maintenance be completed at the designat...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the Normal Scheduled Maintenance. Thisschedule is presented at specific mileage (kilometer) intervals withexceptions as noted. Normal scheduled maintenance Every 7500 miles(12000 km) or sixmonths (whichevercomes first) Change engine...

Other maintenance items Every 30000 miles(48000 km) Replace climate-controlled (heated andcooled) seat filter (if equipped). Replace engine air filter. Every 97500 miles(156000 km) Replace spark plugs. Every 105000 miles(168000 km) Change engine coolant. * Inspect accessory drive belt(s). ** Every 1...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery, taxi, patrol car or livery) Inspect frequently,service as required Replace engine air filter. Every 5000 miles(8000 km) Inspect brake system. Inspect wheels and related components forabnormal noise...

Off-road operation Inspect frequently,service as required Inspect steering linkage, ball joints andU-joints. Lubricate if equipped with greasefittings. Replace engine air filter. Every 5000 miles(8000 km) Change engine oil and filter. * Inspect the wheels and related components forabnormal noise, we...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a leak is suspected, service is required or the assembly has beensubmerged in water. D...

ENGINE COOLANT CHANGE RECORD Initial change Six years or 105000 miles (168000 km)(whichever comes first) After initial change Every three years or 45000 miles (72000 km) Engine Coolant Change Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C O...

• Do not leave playing devices in your vehicle during extreme conditionsas it could cause them damage. See your device’s manual for furtherinformation. • Do not attempt to service or repair the system. See your authorizeddealer. For your safety, some SYNC functions are speed-dependent. Their use isl...

Phone Options during an Active Call During an active call, you have additional menu features which becomeavailable such as putting a call on hold, joining calls, etc. Use the arrowbuttons to scroll through the menu options. To access:1. Press MENU during an active call.2. When Active Call Menu is se...

When you select: You can: Call History Access your call history log.1. Press OK to select, then scroll through your callhistory options (incoming, outgoing or missed).2. Press OK when the desired selection appears inthe display.3. Press the phone button to call the selection. Return Exit the current...

When you select: You can: Phonebook 1,2 Allows you to access your downloaded phonebook.1. Press OK to confirm and enter. If yourphonebook has fewer than 255 listings, theyappear alphabetically in flat file mode. If there aremore, they are organized into alphabeticalcategories.2. Scroll until the des...

Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages.The system can also read incoming text messages to you so that you donot have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature. ...

Delete All Messages? allows you to delete current text messages from SYNC (not your phone). To delete the messages, press OK to select. Thedisplay indicates when all your text messages have been deleted andSYNC returns you to the text message menu. Note: SYNC does not automatically download all of y...

When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e.,add, delete, download). Press OK to selectand scroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push c...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off.Press OK and scroll to toggle between On andOff. When the desired selection is chosen,press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates allBluetooth features. Delete Device Delete...

SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visitwww.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, U.S. only): Provides ...

Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle HealthReport only monitors c...

To run a report using the phone button:1. Press the phone button to enter Phone Menu.2. Scroll until Vehicle Health is selected and press OK.3. Scroll to select from the following options: Vehicle Health Report Options User Preferences:Press OK to selectand enter the menu.Scroll to select from: Auto...

Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel.2. Say “Good-bye” from the SYNC Services main menu. SYNC Services Quick Tips Personalizing You can personalize your Services feature toprovide quicker access to your most used orfavorite information. You can sa...

“USB” “Search song <name>” 1 “Search track <name>” 1,3 “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” 1 “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. 2 Voice commands which are only available in folder mode. 3 Voic...

Voice Command Guide “Refine” This allows you to make your previouscommand more specific. For example, if youasked to search and play all music by acertain artist, you could then say “refinealbum” and choose a specific album from thelist to view. If you then select Play, the systemonly plays music fr...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plugin devices to charge them (if supported byyour device). Once connected, the systemindexes any readable media files. (The timerequired to complete this depends on the sizeof the med...

When you select: You can: Media Settings Choose to shuffle or repeat your music andselect your Autoplay settings. Once theseselections are turned on, they remain on untilturned off. Press SEEK to play the previousor next track. Note: Some digital media players require both USB and line in ports to s...

When you select: You can: Similar Music Play music similar to what is currently playingfrom the USB port. The system uses themetadata information of each song to compile aplaylist for you.Press OK to select. The system creates a newlist of similar songs and begins playing. Themetadata tags must be p...

4. Press OK and then scroll to select from: When you select: You can: Add BluetoothDevice * Allows you to pair additional devices to thesystem.1. Press OK to select and press OK againwhen Find SYNC appears in the display.2. Follow the directions in your phone’s userguide to put your phone into disco...

Advanced Menu Options This menu allows you to access settings such as prompts, language,performing a master reset as well as returning to factory defaults.1. Press AUX and then MENU to access the Media Menu.2. Scroll until System Settings appears and select OK.3. Scroll until Advanced appears.4. Pre...

Vehicle Health Report/Services (Traffic, Directions and Information) Issues Issue Possible Cause(s) Possible Solution(s) I received a textthat the VehicleHealth Report isnot activated. • Your account may not beactivated on thewebsite, OR • You may have the wrong VIN(vehicleidentificationnumber) list...

NAVIGATION CONTROLS WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend...

L. MENU: • Press this button to access the system menu. • Press while the system menu is active to access the menu tabs ofDisplay, Clock, Feedback Settings, System Settings and Valet Mode. M. SOUND: • Press this button to access the sound menu. • Press while the sound menu is active to access the me...

Display mode voice commands “Night” “Auto” “Help” STATUS BARS The top status bar shows thecurrent mode, exterior temperature,time and display icons if you haveenabled Bluetooth or other options. The bottom status bar shows theHome icon and may also show theArtist and Title of the currentlyplaying CD...

• The file path must be 255 characters or fewer. • Up to 256 files or folders can display in one folder. • The CD or DVD must be ISO 9660 format. UDF format is not supported. To load photos:1. Touch the left side of the home screen.2. Touch the Add button. When the disclaimer appears asking to confi...

Helpful Hints • Make sure the interior of your vehicle is as quiet as possible. Windnoise from open windows and road vibrations may prevent the systemfrom correctly recognizing spoken commands. • After pressing the voice icon, wait until after the tone sounds andListening appears before saying a com...

SYSTEM MENU FEATURES Your system offers many menu features, such as allowing you to adjustthe touchscreen brightness, time and language, feedback and systemsettings. You can access these options by pressing the MENU hardbutton. If you select: You can: Display Brightness allows you to adjust screen b...

ENTERTAINMENT Your system offers many media options. You can access these optionsusing the touchscreen or voice commands. AM/FM Radio Press the RADIO hard button. To change between AM, FM1 and FM2, touch the AM or FMtab. When you select: You can: Show Options Scan allows you to hear a brief sampling...

When you select: You can: Show Presets View the preset stations. Save a station bypressing and holding one of the memorypreset areas. There is a brief mute while theradio saves the station. Sound returns whenfinished. Set PTY/All Select a category of music you would like tosearch for and then choose...

HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Yoursystem has a special receiver that allows it to receive digital broadcasts(where available) in addition to the analog broadcasts, i...

When you select: You can: Tune Go up and down the frequency in individualincrements.If the current station has multiple digitalbroadcasts, the multicast indicator appears.Press Tune repeatedly to advance through allavailable broadcasts. If you are on the lastbroadcast channel, press to advance to th...

HD Radio Reception and Station Troubleshooting Potential Reception Issues Reception area If you are listening to a multicast station andyou are on the fringe of the reception area,the station may mute due to weak signalstrength.If you are listening to HD1, the systemswitches back to the analog broad...

HD Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the...

SIRIUS® Satellite Radio Voice Commands If you are listening to SIRIUS satellite radio, press the voicebutton on the steering wheel control. When prompted, say anyof the commands in the following chart. If you are not listening to SIRIUS satellite radio, press the voice buttonand, after the tone, say...

SIRIUS® Information Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or without notice to you. FordMotor Company shall not be responsible for any such programming c...

CD Press the MEDIA hard button, and then select the CD tab onthe touchscreen. If there is no disc in the system, NO DISCappears in the status bar and you cannot access the CD screen. Once a disc is loaded, you can choose from Scan, Compress, Repeat,Shuffle, Track List and Record. When you select: Yo...

MP3 Press the MEDIA hard button, and then select the CD tab onthe touchscreen. If there is no disc in the system, NO DISCappears in the status bar and you cannot access the CD screen. Once a disc is loaded, you can choose from Scan, Compress, Repeat,Shuffle, Folder Mode and Folder List. When you sel...

Disc Voice Commands If you are listening to or watching a disc, press the voice buttonon the steering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to or watching a disc, press the voice button and,after the tone, say “Disc”, then any of the co...

Video CD Voice Commands If you are watching a video CD, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not watching a video CD, press the voice button and, after thetone, say “Video CD”, then any of the commands in the fo...

Accessing the Music in Your Jukebox Once you have saved music to your jukebox, you can then choosedifferent ways to play the music.1. Press the MEDIA hard button on the navigation system.2. Select the Jukebox tab on the touchscreen. You can then select from the following options: When you select: Yo...

Creating a Playlist Press the MEDIA hard button, and then select the Jukebox tab on thetouchscreen.1. Select Options.2. Select Edit Playlists, then which playlist you would like to create.3. Select which category you would like to access from your saved music.4. Select the desired songs and then pre...

User Device If your vehicle is equipped with SYNC®, there is a User Device tab. Formore information, see the SYNC® chapter. Line In (Auxiliary Input Jack) Your vehicle is equipped with an audio input jack, which allows you toplug a portable audio device into your vehicle’s audio system. To turnthis ...

Press the I (information) button, then select Sirius Travel Link.Choose from any of the following services: When you select: You can: Traffic On Route Identify traffic incidents on your route, nearbyyour vehicle’s current location or near any ofyour favorite places (if programmed). Traffic Nearby My...

Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). FreewayEntrance/Exit Touch this button to select an entrance andexit point to a freeway you select. You can sortthe entrance and exit point alphabetically or inorder of distance ...

Within these main categories, there are subcategories, which containmore listings: Subcategories Restaurant Auto Dealership Parking Public Transit Home & Garden Education Personal Care Services Setting Your Navigation Preferences Select settings for the system to take into account when planning ...

Navigation Preferences Avg. Speed:Residential When this feature is on, the system displaysthe average speed on a residential road,initially set to 25 mph (40 km/h). You canchange the setting for your drivingpreferences. This setting helps estimate yourarrival time at a destination based on yourdrivi...

Navigation Preferences Calibrate Position allows you to adjust the direction of your vehicle by pressing the arrow buttons onthe screen. Distance allows you to recalibrate the distance to the destination while your vehicle is moving. Restore DefaultSettings Touch the Reset button to return the setti...

Map Icons Vehicle mark shows the current location of your vehicle. It stays in the center of the map display, except when in scrollmode. Scroll cursor allows you to scroll the map; the fixed icon is in the center of the screen. The map position closest to the cursoris in a window on the top center p...

Map Scale The map display scale has 17 levels, ranging from0.02 miles (.03 kilometers) to 1000 miles (1600 kilometers).The system synchronizes the zoom scales for North Up,Heading Up and 3D Map views. In Map Mode, you can zoom in or out, changing the displayscale, by touching an arrow button on the ...

Quick-touch Buttons When in map mode, touch anywhere on the map display to access thefollowing options: When you select: You can: Set as Dest Select a scrolled location on the map as yourdestination. You may scroll the map bypressing your index finger on the map display.When you reach the desired lo...

Symptoms Possible Cause Action A pop-up windowdisplays “Navigationfault. A system faulthas been detected thatmay cause thenavigation to performabnormally. Pleasecontact yourdealership.” There is a systemhardware or softwareerror. Contact yourauthorized dealer. A pop-up windowdisplays “Error. PINsdid...

GENERAL INFORMATION SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMPANY from an affiliate of MicrosoftCorporation (“MS”). Those installed software products of MS origin, aswell as associated media, printed materials, a...

• Security Updates/Digital Rights Management: Content owners use the WMDRM technology included in your DEVICE to protect theirintellectual property, included copyrighted content. Portions of theSOFTWARE on your DEVICE use WMDRM software to accessWMDRM-protected content. If the WMDRM software fails t...

INTELLECTUAL PROPERTY RIGHTS: All title and intellectual property rights in and to the SOFTWARE (including but not limited toany images, photographs, animations, video, audio, music, text and“applets,” incorporated into the SOFTWARE), the accompanying printedmaterials, and any copies of the SOFTWARE...

SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISINGFROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OFTHE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANYREMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALLMS, MICROSOFT CORPORATION AND/OR THEIR AFFILIATES BELIABLE FOR ANY AMOUNT IN EXCESS OF ...

General operation Voice Command Control Functions within the Windows Automotive-based system may beaccomplished using only voice commands. Using voice commands whiledriving allows you to operate the system without removing your handsfrom the wheel. Prolonged Views of Screen Do not access any functio...

Route Safety Do not follow the route suggestions if doing so would result in an unsafe orillegal maneuver, if you would be placed in an unsafe situation, or if youwould be directed into an area that you consider unsafe. The driver isultimately responsible for the safe operation of the vehicle and th...

Restrictions: Except where you have been specifically licensed to do so by (Licensee), and without limiting the preceding paragraph, you maynot (a) use this Data with any products, systems, or applicationsinstalled or otherwise connected to or in communication with vehicles,capable of vehicle naviga...

Termination for Breach or Bankruptcy: (Licensee) and its licensors, including NAVTEQ, may terminate this Agreement if you breach any ofits terms. Upon any such termination, you shall immediately cease youruse of the Data and return all copies thereof to LICENSEE or NAVTEQ,as instructed. (Licensee) a...

Gracenote® Copyright CD and music — related data from Gracenote, Inc., copyright 娀 2000–2007 Gracenote. Gracenote Software, copyright 娀 2000–2007 Gracenote. This product and service may practice one or more of thefollowing U.S. Patents #5,987,525; #6,061,680; #6,154,773, #6,161,132,#6,230,192, #6,23...

911 Assist™ ..............................408 A ABS (see Brakes) .....................229 Accessing call history/phonebook during active call .............398 Accessing the help screen .......467 Accessing the music inyour jukebox .....................461–462 Accessing your media menufeatures .........

SecuriLock passive anti-theftsystem ..........................................76 Selecting your media source(USB, Line in, BT audio) .........420 Setting a destination ................468 Setting the clock .......................121 Side air curtain ...........................51 Side-curtain airbags...