Ford 2012 F-150 Raptor v.3- Manuals

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CELL PHONE USE The use of mobile communications equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster shown in standard measure; metricsimilar. Uplevel clusters similar. Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one ...

Uplevel message center Note: Some warning lights are reconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These lightsfunction the same as the otherwarning lights. The first threepositions will only display onewarning telltale at a time; the lastthree positions can...

Powertrain malfunction/Reducedpower/Electronic throttlecontrol (RTT): Displays when the engine has defaulted to a“limp-home” operation or when a transmission problem has beendetected and shifting may be restricted. If the light remains on, have thesystem serviced immediately by your authorized deale...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be checked. Referto Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will illuminate for...

ignition is turned on, or remains on, have the system servicedimmediately by your authorized dealer. Four-wheel drive high (RTT) (ifequipped): Displays when four-wheel drive high is engaged. Ifthe light fails to display when theignition is turned on, or remains on, have the system servicedimmediatel...

GAUGES Standard measure base cluster with automatic transmissionshown; metric similar and uplevel clusters similar. 1. Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H). Ifthe needle falls below the normal range, stop the...

BASE MESSAGE CENTER Your vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicle problems and variousconditions with an informational message followed by a long indicatorchime. The message center display is located in the instrument cluster. Info...

AVG MPG (L/100km) Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km. If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed for ...

TBC GAIN (if equipped) Displays the level of trailer brake gain or if the trailer is not connected. System check and vehicle feature customization Press the SETUP button repeatedlyto cycle the message center throughthe following features: RESET FOR SYSTEM CHECK When this message appears, pressthe RE...

COURTESY WIPE This feature allows for an extra swipe of the wipers after a wipe/washcycle. Press the RESET button to turn it on or off. EASY ENTRY This feature automatically moves the driver’s seat backwards for easyexit/entry from the vehicle. Press the RESET button to turn the easy entry/exit seat...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center will cyclethe display to show all warnings by displaying each one for four seconds. The message center will display the ...

Main menu From the main menu screen you can choose the following: • Gauge Mode • Trip A/B • Fuel Economy • Truck Apps (if equipped) • Settings • Information Scroll up/down to highlight one of the options, then press the right arrowkey or OK to enter into that menu option. Gauge Mode Gauge Detail: In...

*Trailer: Change ActiveTrailer When this is highlighted, press the right arrow keyto change the currently selected trailer. Use the upand down arrows to select a trailer and press theOK button to choose the highlighted trailer. Adding a new trailer– Use the up/down arrows tohighlight “New Trailer” f...

Settings In this mode, you can configure different driver setting choices (ifequipped). Press the right arrow key (when in the Settings menu) toreach the Driver Assist menu: Driver Assist* Rear Park Aid On/Off Rear VideoCamera Camera Delay On/Off Visual Park Aid On/Off Guidelines Fixed/Off Zoom Leve...

Information In this mode, you can view different vehicle system information andperform a system check. When “Press OK for info” is displayed, pressing OK will give youinformation on the currently selected/displayed options. Information isonly available when traveling less than 3 mph (5 km/h). MyKey ...

AUDIO SYSTEMS AM/FM stereo system (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility ...

CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into the system, CD/MP3 play will begin where it ended last. If no CD is loaded,NO DISC will appear in the display. LOAD:For a single CD system– This control is not operational. To load a CD, simply insert the disc, label side...

DIRECT: Press DIRECT then enter the desired channel (i.e. 002) using the memory preset buttons (0–9). If you only enter one digit, press OKand the system will go to that satellite channel. If you enter three digits,the system will automatically go to that channel, if available. You maycancel your en...

SATELLITE RADIO MENU: Press MENU when satellite radio mode is active to access. Press OK to enter into the satellite radio menu.Press to cycle through the following options: • CATEGORY- Press OK to enter category mode. Press to scroll through the list of available SIRIUS channel Categories (Pop, Roc...

d. DISABLE ALERTS/ENABLE ALERTS: Press OK to enable/disable the satellite alert status which alerts you when yourselected songs are playing on a satellite radio channel. (The systemdefault is disabled.) SONG ALERTS ENABLED/DISABLED will appearin the display. The menu listing will display the opposit...

FADE: Press SEEK to adjust the audio between the back (B) and front (F) speakers. SPEED COMPENSATED VOLUME: With this feature on, radio volume automatically gets louder with increasing vehicle speed to compensatefor road and wind noise. The default setting is off. Use SEEK to adjust between SPEED OF...

Auxiliary input jack (Line in — if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is ...

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and also to chargedevices if they support this feature.For further information on this feature, refer to Accessing and using your USB port in the SYNC 威 ...

• Wipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and...

MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and folder structureas follows: • There are two different modes for MP3 disc playback: MP3 track mode(system default) and MP3 folder mode. For more information on trackand folder mode, refer to Sample MP3 structure in th...

SINGLE ZONE CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fogand thin ice. The system will automatically provide outside air to reducewindow fogging. Press this button again to return to the prev...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Fan speed control: Press to increase the fan speed. 2. Defrost: Distributes outside air through the...

4. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. A/Cengages automatically in MAX A/C, (defrost) and (floor/defrost). 5. AUTO: Press to engage full automatic operation. Select the desired temperature using the temperature ...

10. Driver heated seat control: Press to control the driver heated seat. Refer to Heated seats in the Seating and Safety Restraints chapter for more information. 11. Power/Driver temperature: Press to activate/deactivate the climate control system. When the system is off, outside air is preventedfro...

• : Distributes air through the floor vents and rear seat floor vents. 4. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. A/Cengages automatically in MAX A/C, (defrost) and (floor/defrost). 5. AUTO: Press to engage automati...

10. Passenger cooled seat: Press to control the passenger cooled seat. Refer to Heated and cooled seats in the Seating and Safety Restraints chapter for more information. 11. Driver heated seat: Press to control the driver heated seat. Refer to Heated and cooled seats in the Seating and Safety Restr...

TOUCHSCREEN FUNCTIONS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. Temperature: Press the up and down arrows on the left side of the screen to increase/decrease the airflow temperature for the driver side ofthe vehicle. ...

VOICE COMMANDS IN CLIMATE MODE Please refer to the Voice commands in climate mode section of the Navigation supplement for more information on using voice commands with the climate control system. Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost). Temper...

4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. REAR WINDOW DEFROSTER (IF EQUIPPED) R The rear defroster control is...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position to turn on the parking lamps. Rotate clockwise to the secondposition to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights no...

High beams Pull the lever fully past the detentto activate. Pull the lever fully againto deactivate. Flash-to-pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. In order for the DRLs to function:...

4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge towards theright. If this edge is not at thehorizontal reference line, the beam will need to be adjusted so the edgeis at the same height as the horizontal reference line. 5. Locate the vertical adjuster oneach h...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerbutton is pressed until thecourtesy lamp comes on. • the remote entry controls arepressed and the ig...

Function Number of bulbs Trade number Backup lamp (Harley) 2 921 Rear stop/turn/sidemarker/taillamp (styleside) 4 3057K High-mount brakelamp 1 912 Front row map lamps 2 W5W Rear dome lamp 1 578 Rear dome/courtesy lamps 3 578 Rear courtesy/reading/cargo lamps 2 912 License plate lamp 2 194 Exterior m...

Replacing front parking lamp/turn signal/sidemarker bulbs 1. Make sure that the headlamp control is in the off position and openthe hood. 2. Remove the pushpin that holdsthe air deflector/protective coverfrom the upper inboard corner ofthe lamp. 3. Loosen the three retaining bolts(two at top of lamp...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate toward you to decrease thespeed of the wipers. Speed-dependent wipers (if equipped): When the wiper control is set to any of the interval settings except the longest pause set...

Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick press and hold: thewipers will swipe three times withwasher fluid. • a long press and hold: the wipers and washer fluid will be activated forup to ten seconds. Note: Do not op...

WARNING: Never adjust the steering column when the vehicle is moving. Power Tilt/Telescope Steering Column (if equipped) The steering column can beadjusted using the control on theside of the steering column. Pressand hold the front or rear of thecontrol to adjust the telescope.Press and hold the to...

On vehicles with memory feature, to prevent damage to the steeringcolumn, the steering column is designed to set a stopping position justshort of the end of the column position. If the steering columnencounters an object while moving up or down, a new stopping positionwill be set. To reset the steer...

The power point can switch to a fault mode when it is overloaded,overheated, or shorted. For overloading and shorting conditions, unplugyour device and turn the ignition key off then on. For an overheatingcondition, let the system cool off, then turn the ignition key off then on. The 110V AC power p...

POWER WINDOWS (IF EQUIPPED) WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pet...

Restoring the one-touch up functionality (front windows only) Under low battery power conditions, one-touch up only functionality maybe lost. To reset this function after restoring full battery power, pull theswitch to the one-touch up position, hold the switch until the glassreaches the stall posit...

The mirrors will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up. Do not block the sensors on the front and back of the interior rearview mirror since this may impair proper mirror performance. Note: A rear center pas...

On vehicles not equipped with rear defrost, press the heated mirrorcontrol located on the climate control panel. For more information refer to the Climate Controls chapter. Note: If your vehicle is equipped with the auto dimming feature, the driver’s side mirror glass is thicker and will take longer...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when thevehicle is stopped and the gearshift lever is in the P (Park) position. Thecontrol is located on the side of the steering column. Press and hold the rear of thecontrol to adjust the pedals towa...

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed controls The speed controls are located on the ste...

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) The appearance of your vehicle’s universal garage door opener will varyaccording to your option package. Before programing, make sure youidentify which transmitter you have by comparing it to the graphicsbelow. HomeLink 威 Car2U 威 Home Automation System Note...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. WARNING: Do not use the system with any garage door opener that does not have the...

2. Return to your car. 3. Press and hold the functionbutton you want to program for2 seconds, then release. Repeat thisstep. Depending on the brand ofgarage door opener you may needto repeat this sequence a third time. To program additional buttonsrepeat steps one through four. For questions or comm...

Programing the transmitters To program HomeLink 威 to the transmitter you must first put the transmitter into programming mode. To do this A. Red LED B. Green LED 1. Press and hold one of the buttons on the hand-held transmitter for10 seconds. The LED light will change from green to green and red. 2....

STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features – VOL + (Volume): Press to decrease or increase the volume. (Seek): Press to select the previous/next radio stationpreset, CD track or satellite radiostation preset depending on whichmedia mode you are in. MEDIA: Press repeatedly to scroll...

For further information on the SYNC 威 system, refer to the SYNC 威 supplement. Navigation system/SYNC 威 hands-free control features (ifequipped) Press control briefly until the voice icon appears on the Navigation display to use the voicecommand feature. Press to activate phone mode or answer a phone...

To open the moon roof: Press and release the SLIDE control and themoon roof will open automatically tothe “comfort” position. Press andrelease again to fully open. Pressthe switch again to stop the moonroof. To close the moon roof: Pull and release the SLIDE control, the moonroof will close automati...

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and int...

1. Before removing the tailgate,locate and disconnect the tailgatein-line connector. It is located underthe pickup box on the passengerside of the vehicle near the sparetire. 2. Install a protective cap (locatedin the glove box) onto the in-linerearview camera system connectorthat remains under the ...

2. Open the latches to release thepanels. 3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels. Driver Controls 134 2012 F-150 (f12) Owners Guide, 3rd PrintingU...

Cross bars: Aluminum cross bars with T-slot channels in all four sides, and a latch mechanism that allows the end supports to snap over theexisting cleats. Cross bars are rated to hold loads up to 100 lb (45 kg)load evenly distributed between the two crossbars, and the T-slots aresized to accept ind...

Bed divider: This panel will keep small items up to 400 lb (180 kg) in position in the pickup box. Also includes T-slots to allow attachment ofindustry-standard roof rack accessories. • To remove bed divider, lift handle on each side and lift end supportshroud off of the cleat. • To install bed divi...

Side mounted tool bins: Watertight bins can be positioned at any point along the side rails and can be easily removed (even when full), andcarried to wherever the contents are needed. Each bin will hold up to60 lb (27 kg) of cargo, and has a drain plug for use as a cooler. Note: When multiple bins a...

KEYS Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-p...

MyKey 威 restricted features Standard settings – These settings cannot be changed • The audio system will be muted whenever Belt-Minder 威 is activated until the safety belts are buckled. Refer to the Seating and Safety Restraints chapter for a detailed description of Belt-Minder 威 operation. • Low fu...

Using MyKey 威 with remote start systems MyKey 威 is not compatible with non Ford-approved aftermarket remote start systems. If you choose to install a remote start system please seeyour authorized dealer for a Ford approved remote start system. The following information MAY help customers who choose ...

Note: For all vehicles with a non Ford-approved remote start installed, it is possible to program all “real” keys as MyKeys 威 , in which case, you will need to use your remote start system to reset all MyKeys 威 as admin keys by doing the following: 1. Enter the vehicle, close all doors. 2. Remote st...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a ...

CHILDPROOF DOOR LOCKS (ON VEHICLES WITH REAR DOORS) • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when thechildproof door locks are set, butthe doors are unlocked. The childproof locks are located onthe rear edge of each rea...

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The IKT allows you to: • remotely unlock the ...

Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and one step door unlocking by pressing andholding both the and buttons simultaneously on the remote entry transmitter for approximately four seconds. The ...

2. Press and hold control button 1for five seconds. A tone will beheard after two seconds confirmingmemory position has been set.Continue to hold until a second toneis heard after five seconds. 3. Within three seconds press . 4. Wait 10 seconds, then press . 5. Repeat this procedure formemory 2 and ...

4. Insert the new battery. Refer to the instructions inside the IKT for thecorrect orientation of the battery. Press the battery down to ensure thatthe battery is fully seated in the battery housing cavity. 5. Snap the battery cover back onto the key. Note: Replacement of the battery will not cause ...

Remote start (if equipped) Your vehicle may be equipped with the remote start feature which allowsyou to start the engine from outside the vehicle. If your transmitter hasa icon, you have remote start. The remote start feature has an extended operating range which allows you to remote start your veh...

Extending the engine run time To keep the engine running for another remote start duration, repeatSteps 1 and 2 with the engine still running. If you programmed theduration to last 10 minutes, the second 10 minutes will beginimmediately so that, for example, if the vehicle had been running fromthe f...

4. To associate the entry code with a memory setting, enter a sixth digitto indicate which driver should be set in a memory recalled by thepersonal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 settings. • Pressing other keypad buttons or not pressing a ke...

Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of eachother. The interior lamps will illuminate after entering a valid keypadentry code. To unlock all doors, pr...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Turn the ignition to the on position with a programmed coded ignitionkey. • Unlock the doors by using your keyless entry pad. • If using a ke...

FRONT SEATS WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before...

To reinstall the non-adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. WARNING: The non-adjustable head restraint is a safety device. It should be installed whenever the seat is occupied. WARNING: To mini...

• To gain access to the storagecompartment (if equipped) underthe center seat cushion, lift thelatch to open the lid. Using the manual lumbar support (if equipped) For more lumbar support, turn thelumbar support control toward thefront of vehicle. For less lumbar support, turn thelumbar support cont...

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the controlfor additional support. Press the rear side of the control toreduce support. Adjusting the front power seat (if equipped) WARNING: Never adjust the ...

To install a filter: 1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing. 2. Push in on the center of theoutside edge of the filter and rotateup into the housing until it clips intoposition. REAR SEATS Second row head restraints Your vehicl...

Folding rear head restraints (if equipped) The outboard rear head restraintsmay have a folding feature. Pressthe button on the side of the headrestraints to fold them forward. Pullthe head restraints up to unfold. Folding up the rear seats (SuperCab only) The rear seat has a split 60/40 cushion. Eac...

Folding Up the Rear Seats (SuperCrew Vehicles Only) The rear seat has a split 60/40 cushion. Each seat cushion can be flippedup into a vertical storage position. Rotate the seat cushion up by liftingon the corner until it locks into thevertical storage position. Note: The handle on the bottom of the...

To operate the heated seats: • Push the indicated side of thecontrol for maximum heat. • Push again to deactivate. • Push the indicated side of thecontrol for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While theignition is in the on position,...

• Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety belt usage sensors, driver seat positionsensor, and indicator lights. How does the Per...

SAFETY BELT SYSTEM WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the veh...

WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a childanywhere near them. WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts fo...

While you are fastened in the safety belt, the combination lap/shoulderbelt with a cinch tongue adjusts to your movement. However, if youbrake hard, turn hard, or if your vehicle receives an impact of 5 mph(8 km/h) or more, the safety belt will become locked and help reduceyour forward movement. Res...

Safety belt locking modes All safety restraints in the vehicle are combination lap and shoulderbelts. The driver safety belt and the optional front center seat’s safetybelt have the first locking mode only. All outboard passenger and rearsafety belts have both types of locking modes described as fol...

How to use the automatic locking mode 1. Buckle the combination lap andshoulder belt (front safetybelt/buckle shown, rear similar). 2. Grasp the shoulder portion andpull downward until the entire beltis pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. Thi...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andright front passenger seating positions. The safety belt pretensioner removes some slack from the safety beltsystem at the start of a crash. The safety belt pretensioner uses thesame crash sensor system...

Safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,pull on the center button and slidethe height adjuster do...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 6 mph and1-2 minutes have elapsed sincethe ignition switch has beenturned to ON... The Belt-Minder 威 feature is activated - the safety belt warning lightillumi...

Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are deactivated/activated independently. When deactivating/activatingone seating position, do not buckle the other position as this willterminate the process. Read Steps 1 - 4 thoroughly before proceeding ...

3. For the seating position being disabled, buckle then unbuckle thesafety belt three times, ending in the unbuckled state. • After Step 3, the safety belt warning light will be turned on for threeseconds. 4. Within approximately seven seconds of the light turning off, bucklethen unbuckle the safety...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system is designed to work inconjunction with the safety belts to help protect the driver and frontoutboard passenger from certain upper body injuries. The term“supplemental restraint” means the airbags are intended as a su...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. WARNING: All occupants of the vehicle, including the driver, s...

If two adults and a child occupy a Regular Cab , properly restrain the child in the center front unless doing so would interfere with driving thevehicle. This arrangement provides lap and shoulder belt protection forall occupants, and airbag protection for the adults. All occupants of thevehicle sho...

While the system is designed to help reduce serious injuries, it may alsocause minor abrasions, swelling or temporary hearing loss. Becauseairbags must inflate rapidly and with considerable force, there is the riskof death or serious injuries such as fractures, facial and eye injuries orinternal inj...

• the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period oftime, • a child or a small person occupies the front passenger seat. Note: When the passenger airbag off light is illuminated, the passenger (seat mounted)...

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat, the passenger airbag will be disabled. Even though thepassenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated accord...

Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicatethe condition of the system. Refer to Airbag readiness in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is indicated...

WARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not rep...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Warning lights and chimes in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the syst...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safety seat(sometimes called aninfant carrier, convertibleseat, or toddler seat). Smal...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsand toptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybel...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced25.7 inches (652 mm) apart. The standardized spacing for LATCH loweranchors is 11 inches (280 mm) center to center. A child seat with rigidLATCH ...

The passenger seats of your vehicle are equipped with built-in tetherstrap anchors located behind the seats as described below. The tether anchors in your vehicle may be loops of webbing above theseatback or an anchor bracket behind the seat on the rear edge of theseat cushion. The rear seat in the ...

Rear seat tether strap attachment (SuperCab and SuperCrew) There are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow). These loops are to beused as both routing loops andanchor loops for up to three childsafety seat tether straps. Forexample, the ce...

3. Tighten the tether strapaccording to the child seatmanufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child beinginjured in a collision greatly increases. If your child restraint system is equipped with a tether strap, and thechild restraint manufacturer recom...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thiscondition. Do not introduce any item thicker than this under the boosterseat. Check with the booster seat manufacturer’s instructions. The importance of shoul...

NOTICE TO OWNERS ABOUT HIGH PERFORMANCE TIRES Note: Your vehicle is equipped with high performance tires. When first driving the vehicle after it has been parked for a period of time, you mayexperience a temporary ride disturbance. This is a characteristic of thetires and should be no reason for con...

VEHICLE CHARACTERISTICS Four-wheel drive (4WD) system (if equipped) A vehicle equipped with 4WD (when selected) has the ability to use allfour wheels to power itself. This increases traction which may enable youto safely drive over terrain and road conditions that a conventionaltwo-wheel drive vehic...

How Your Vehicle Differs from Other Vehicles SUVs and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbody components. • Shorter ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

You are strongly urged to buy a reliable tire pressure gauge, as automaticservice station gauges may be inaccurate. Ford recommends the use of adigital or dial-type tire pressure gauge rather than a stick-type tirepressure gauge. Use the recommended cold inflation pressure for optimum tireperformanc...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety Practices WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may f...

Tire Rotation WARNING: If the tire label shows different tire pressures for the front and rear tires and the vehicle is equipped with TPMS (tire pressure monitoring system), then the settings for the TPMSsensors need to be updated. Always perform the TPMS reset procedureafter tire rotation. If the s...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identifi...

5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

replacement or alternate tires or wheels on the vehicle that prevent theTPMS from functioning properly. Always check the TPMS malfunctiontelltale after replacing one or more tires or wheels on your vehicle toensure that the replacement or alternate tires and wheels allow theTPMS to continue to funct...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function o...

Low tirepressurewarning light Possiblecause Customer action required Flashing warninglight Spare tire inuse Repair the damaged road wheel/tire andreinstall it on the vehicle to restoresystem functionality. For a descriptionon how the system functions, refer to When your temporary spare tire isinstal...

TPMS Reset Procedure WARNING: To determine the required pressure(s) for your vehicle, refer to the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the dooredge that meets the door-latch post, next to the driver’s seatingposition), or Tire Label loc...

7. Remove the valve cap from the valve stem on the right front tire;decrease the air pressure until the horn sounds. 8. Remove the valve cap from the valve stem on the right rear tire;decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire;d...

Follow these guidelines when using snow tires and chains: • If possible, avoid fully loading your vehicle. • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines. • Drive cautiously. If you hear the chains rub or bang aga...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. Tires, Wheels and Loading 264 2012 F-150 (f12) Owners Guide, 3rd PrintingUSA (fus)

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

TRAILER TOWING Your vehicle may tow a class I, II, III or IV trailer provided the maximumtrailer weight is less than or equal to the maximum trailer weight listedfor your engine and rear axle ratio on the following charts. When driving with a trailer or payload, a slight takeoff vibration orshudder ...

SuperCrew Engine Rear axle ratio Maximum GCWR - lb (kg) Maximum Trailer Weight - lb (kg) 3.5L (Heavy Payload Package) 3.73 17100 (7756) 11300 (5126) 5.0L 3.55 13500 (6123) 7900 (3583) 3.73 14900 (6759) 9300 (4218) 5.0L (Heavy Payload Package) 3.73 15300 (6940) 9500 (4309) 6.2L (Max Trailer Tow Packa...

Hitches Do not use a hitch that clamps onto the vehicle’s bumper or attaches tothe axle. You must distribute the load in your trailer so that 10–15% ofthe total weight of the trailer is on the tongue. Weight-Distributing Hitches When hooking-up a trailer using a weight-distributing hitch, always use...

Trailer Brakes WARNING: Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collisiongreatly increase. Electric brakes and manual, automatic or surge-type trailer brakes aresafe if inst...

The trailer brake controller (TBC) is designed to display three items ofinformation in the instrument cluster message center. These are: gainsetting, output bar graph, and trailer connectivity status. They appear inthe message center as follows: • TBC GAIN = XX.X NO TRAILER: The instrument cluster m...

Procedure for adjusting GAIN: The GAIN setting is used to set the TBC for the specific towing conditionand should be changed as towing conditions change. Changes to towingconditions include trailer load, vehicle load, road conditions and weather. The GAIN should be set to provide the maximum trailer...

WIRING FAULT ON TRAILER: This message is displayed when a Short circuit on the electric brake output wire has occurred. If the WIRING FAULT ON TRAILER message is displayed and accompanied by a single chime, with no trailer connected, the problem is with thevehicle wiring from the TBC to the 7–pin co...

• When the vehicle is turned off, the TBC output is disabled and thedisplay is shut down; turning the ignition from off to on awakens theTBC module. • The TBC is only a factory- or dealer-installed item; Ford is notresponsible for warranty or performance of the TBC due to misuse orcustomer installat...

Trailer towing tips • Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • To aid in engine/transmission cooling and A/C efficiency during hot...

RECREATIONAL TOWING Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. Refer to the Climate Controls chapter. Follow these guidelines if you need to tow your vehicle behind anothervehicle, such as a motor home. The guidelines are design...

WARNING: Do not disconnect the battery during recreational towing. Doing so will prevent the transfer case from shifting properly and may cause the vehicle to roll even if the transmission is inP (Park). WARNING: Shifting the transfer case to its neutral position for recreational towing may cause th...

STARTING Positions of the ignition 1. Off — locks the automatictransmission gearshift lever andallows key removal. Note: In order to switch off the engine while thevehicle is in motion, shift to neutraland use the brakes to bring thevehicle to a safe stop. After thevehicle has stopped, turn the engi...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). 2. Turn the key to 4 (start), thenrelease the key as soon as the enginebegins cranking. Your vehicle has acomputer assisted cranking systemthat assists in starting the engine.After releasing the key from the 4(start) ...

If you should experience cold weather starting problems on E 85 ethanol, and neither an alternative brand of E 85 ethanol nor an engine block heater is available, the addition of unleaded gasoline to your tank willimprove cold starting performance. Your vehicle is designed to operateon E 85 ethanol ...

How To Use the Engine Block Heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment, your engine blockheater system may consume anywhere between 400 watts or 1000 wattsof power per hour. Your factory i...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for example when cornering severely oravoiding objects in the roadway. ESC operates by applying brakes to one ormore of the wheels individually and, if nece...

speed at which trailer sway will not grow continuously. This may causethe system to activate multiple times, causing a gradual reduction inspeed. Note: The trailer sway control will only activate at speeds greater than 31 mph (50 km/h). Disabling trailer sway control Trailer sway control can be disa...

WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slungsports cars are designed to per...

Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the on position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Pa...

WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parking brakeprior to doing this procedure. Use wheel chocks if appropriate. WARNING: If the parking brake is fully release...

The TOW HAUL indicator light willilluminate in the instrument cluster. Tow/haul delays upshifts to reduce frequency of transmission shifting.Tow/haul also provides engine braking in all forward gears when thetransmission is in the D (Drive) position; this engine braking will slowthe vehicle and assi...

WARNING: If the engine is revved excessively, or if a malfunction is detected when the hill start assist feature is active, the hill start assist feature will be deactivated. Note: This feature will not operate if the parking brake is activated. Hill start assist keeps your vehicle stationary long e...

Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp objects). If the sensors are covered, it willaffect the accuracy of the RSS. If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned...

The guidelines options are FIXED and OFF. If the vehicle is equippedwith a rearview mirror display and a standard instrument cluster, thefixed guidelines will always remain on. There is no option to turn thefixed guidelines off. Visual park aid alert (if equipped) Visual park aid alert allows the dr...

Always use caution while backing. Objects in the red zone (2) are closestto your vehicle and objects in the green zone (4) are further away.Objects are getting closer to your vehicle as they move from the greenzone (4) to the yellow (3) or red zones (2). Use the side mirrors andrearview mirror to ge...

Press and on the steering wheel controls to select a zoomoption. You can choose from OFF,Level 1, Level 2 and Level 3. Usethe OK button to make a selection.When activating manual zoom mode,the system will always start fromOFF. The manual zoom feature is not available on vehicles equipped arearview m...

• If the image is not clear, then check if there is anything covering thelens such as dirt, mud, ice, snow, etc. If the image is still not clearafter cleaning, have your system inspected by your authorized dealer. BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have a convex spotter mirror built...

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. Note: If 4X4 low is selected while the vehicle is moving above 3 mph (5 km/h), the 4WD system will not perform a sh...

• 4A (4X4 AUTO) - provides electronic control four-wheel drive with power delivered to the front and rear wheels, as required, forincreased traction. This is appropriate for all on-road drivingconditions, including as dry road surfaces, but is especially useful onwet pavement, snow, dirt, or gravel....

• The ELD will not engage if the accelerator pedal is pressed beyond50% during an engagement attempt • In 4x2, 4x4 Auto, and 4x4 High modes, the ELD will automaticallydisengage at speeds above 25 mph (40 km/h) and will automaticallyreengage at speeds below 18 mph (30 km/h). • In 4L (4X4 low), the EL...

Activating the electronic locking differential (ELD) The ELD can be turned on bypulling the 4WD control knobtoward you (4x4 vehicles) or byturning the ELD control knob fromOFF to ON (4x2 vehicles). Once the indicator light is displayedin the message center, both rearwheel axle shafts will be lockedt...

Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating characteristics that are somewhatdifferent from conventional vehicles, both on and off the road. Your vehicle may be equipped with a front air dam t...

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. •...

Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced. After driving through mud, clean off residue stuck to rotating driveshaftsand tires. Excess mud stuck on tires and rotating driveshafts causes animbalance th...

WARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously. Keep speeds down, allow for longer stopping distances and avoidaggressive steering to reduce the chances of a loss of vehicle controlwhich can lead to serious injury ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly. Never drive through waterthat is higher than the bottom ofthe wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or brake capability may be limited.Also, ...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S. : Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours ...

Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the owner’s informationportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, cal...

FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fuel to theengine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you mayrestart your vehic...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — Natural Natural 30A Green Green Green Pink Pink 40A — — Orange Green ...

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 — Powertrain control module (PCM)relay (3.7L, 5.0L and 6.2L engines)...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: If your vehicle is equipped with the tire pressure monitoring system (TPMS), th...

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (...

Location of the spare tire and tools The spare tire is located under the vehicle, just forward of the rearbumper. The jack, jack handle and lug wrench are located in thefollowing locations: Body Style Location Regular Cab Attached to a floor bracketbehind/under the driver’s seat (foreasier access mo...

2. Fully insert the jack handlethrough the bumper hole and intothe guide tube through the accesshole in the rear bumper. 3. Turn the handle counterclockwise until tire is lowered to the ground,the tire can be slid rearward and the cable is slightly slack. 4. Slide the retainer through the center of ...

3. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases significantly and the spare tire carrier ratchets or slips whenthe tire is raised to the maximum tightness. Tighten to the best of yourability, to the ...

Bolt size Wheel lug nut torque* ft-lb N • m M14 x 2.0 150 200 * Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recommended replacement fasteners. Note: Inspect the wheel pilot hole (1) and mounting surface prior toinstallation. Remove any visiblecorrosion or l...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+)...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. Ford recommends your vehicle be towed with a wheel lift or flatbed. Donot tow with a slingbelt. Ford Motor C...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns,...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing orlaundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

3.5L Ecoboost engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remo...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft 威 Premium Windshield Washer Concentrate (ZC-32-A) in the U.S., or Premium Quality Windshield Washer Fluid [CXC-37-(A, B,D, or F)] in Canada, available from your authorized dealer. Thiswasher fluid contains special soluti...

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white cotton cloth. For morethorough cleaning, use a mild soap and wate...

LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH 姞 EDITION) For King Ranch 威 leather seats, refer to a separate section in this chapter. • Clean spills and stains as quickly as possible. • For routine cleaning, wipe the surface with a soft, damp cloth. Formore thorough cleaning, wipe the surface...

Scratches Natural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suchas small scars. These markings give character to the seating covers andshould be considered as proof of a genuine leather product. In order to lesse...

FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its finishes. These qualityproducts have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the style andap...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that islocated on the front bumper under the grill. 3. Lift the hood until the lift cylinders hold it open. Maintenan...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.7L V6 engine 1. Windshield washer fluid reservoir 2. Battery 3. Engine oil dipstick (out of view) 4. Brake fluid reservoir 5. Engine coolant reservoir 6. Air filter assembly 7. Engine oil filler cap (out of view) 8. Power distribution box 1 2 3 4 5 ...

3.5L V6 EcoBoost 姞 engine 1. Windshield washer fluid reservoir 2. Battery 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Engine coolant reservoir 7. Air filter assembly 8. Power distribution box 1 2 3 5 6 7 8 4 Maintenance and Specifications 385 2012 F-150 (f12) Owners G...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

2. Press the retaining clip todisengage the wiper blade, then pullthe wiper blade down toward thewindshield to remove it from thearm (2). 3. To install the new wiper blade,insert the wiper arm hook into thewiper arm (3). 4. While holding the wiper arm, push the wiper blade up and away fromthe windsh...

5. Locate and carefully remove theengine oil level dipstick. See Identifying components in theengine compartment in this chapter for location of dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes or between t...

Engine oil and filter recommendations 3.7L V6, 5.0L V8, and 6.2L V8 engines Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol conforms to thecurrent engine and emissi...

3.5L V6 EcoBoost engine Look for this certificationtrademark. Use SAE 5W-30 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and fueleconomy req...

BATTERY Your vehicle is equipped with a Motorcraft 威 maintenance-free battery which normally does not require additional water during its life ofservice. Note: If your battery has a cover/shield, make sure it isreinstalled after the battery hasbeen cleaned or replaced. For longer, trouble-free opera...

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling ...

in some cases after charging the battery with the external charger, theBMS requires eight hours of vehicle sleep time (key off with doorsclosed) to relearn the new battery state of charge. Prior to relearning thestate of charge, the BMS may disable electrical features (to protect thebattery) earlier...

• Refer to scheduled maintenance information for service interval schedules. If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coola...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quar...

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabove 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion/freeze protection characteristics of theengine coolant ...

Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to an authorized dealer as soon as possible to minimizeengine damage. When ...

Engine fluid temperature management (if equipped) WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperaturesreduce. Your vehicle has been designed to pull a trailer, but...

3. Turn the engine off and wait for it to cool before checking the coolantlevel. WARNING: Never remove the coolant reservoir cap while the engine is running or hot. 4. If the coolant level is normal, you may restart your engine andcontinue on. 5. If the coolant is low, add coolant, restart the engin...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels such as gasoline and ethanol are highlytoxic an...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

If the check fuel fill inlet lamp or CHECK FUEL FILL INLET messagecomes on, the fuel fill inlet may not have properly closed. The inlet mayhave stuck open or debris may be preventing the inlet from fully closing.At the next opportunity, safely pull off the road, turn off the engine,open the fuel fil...

Octane recommendations 3.7L V6/5.0L V8/6.2L V8 engines “Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87 isrecommended. Some stations offer fuels posted as “Regular” with anoctane rating below 87, particularly in high altitude areas. Fuels withoctane levels below 87 are not recomme...

Refilling With a Portable Fuel Container WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel 威 system. This could damage the fuel system and its seal, and may cause fuel to run ontothe ground instead of filling the tank, which could result in serio...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

POWER STEERING FLUID (6.2L V8 ENGINE ONLY) Check the power steering fluid. Refer to scheduled maintenance information. 1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and ...

TRANSMISSION FLUID Checking 6-speed automatic transmission fluid The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does notconsume fluid. However, the fluid l...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft 威 part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/...

Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage tothe engine if the correct air filter element is not used. VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time(30 days or more), re...

• Check under the hood for any foreign material that may have collectedduring storage (mice/squirrel nests). • Check the exhaust for any foreign material that may have collectedduring storage. • Check tire pressures and set tire inflation per the Tire Label. • Check brake pedal operation. Drive the ...

ENGINE DATA Engine 3.7L V6 Engine 5.0L V8 Engine 6.2L V8 Engine 3.5L V6 EcoBoost engine Cubic inches 226 302 378 214 Fuel Minimum 87 octane or E85 Minimum 87 octane or E85 Minimum 87 octane Minimum 87 octane Firing order 1-4-2-5-3-6 1-5-4-8-6-3-7-2 1-3-7-2-6-5-4-8 1-4-2-5-3-6 Ignition system Coil on...

Engine drivebelt routing 3.7L engine 5.0L engine 6.2L engine Maintenance and Specifications 431 2012 F-150 (f12) Owners Guide, 3rd PrintingUSA (fus)

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following this schedule helps protect against major repairexpenses resulting from neglect or inadequate maintenance and may alsohelp to increase the value of your vehicle when you sell or trade it. It is your responsibility to see ...

Genuine Ford Parts and Service When planning your maintenance services, consider your dealership forall your vehicle’s needs. There are a lot of reasons why visiting your dealership for all yourservice needs is a great way to help keep your vehicle running great. Convenience Many dealerships have ex...

Normal Scheduled Maintenance At every oil changeinterval as indicatedby the messagecenter Change engine oil and filter Rotate tires, inspect tire wear and measure treaddepth Perform multi-point inspection (recommended) Inspect automatic transmission fluid level (ifequipped with dipstick); consult de...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS - 3.5L, 3.7L AND 5.0L ENGINES If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the add...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use (i.e. delivery, taxi, patrol car or livery) As required Change engine oil and filter as indicated bymessage center and perform services listed inNormal Scheduled Maintenance chart Inspect frequently,service as re...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently,service as required Replace cabin air filter (if equipped) Replace engine air filter Every 5,000 miles(8,000 km) Inspect the wheels and related components forabnormal noise, wear, looseness or drag Rotate tires, inspect ...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a lea...

Engine Coolant Change Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M...

A Accessory belt ...........................431 Accessory delay ........................105 AdvanceTrac ..............................293 Airbag supplemental restraintsystem ................200–201, 208, 211 and child safety seats ............202description ..............201, 208, 211disposal .........

through water .................329, 333 E Electronic message center ...20, 31 Emergencies, roadside jump-starting ..........................356running out of fuel .........355, 407 Emission control system ..........412 Engine ................................430–431 cleaning ............................

Mirrors ...............................105–106 automatic dimming rearviewmirror ......................................105fold away .................................107heated ....................70, 73, 76, 107programmable memory ..........156side view mirrors (power) .....106signal ....................