Ford 2011 Fusion v.3- Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safeoperation of your vehicle.We recommend aga...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster shown; metric, optional and manualtransmission clusters similar Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one ...

damage your catalytic converter. Drive in a moderate fashion (avoidheavy acceleration and deceleration) and contact your authorized dealeras soon as possible. WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floo...

Airbag readiness: If this light fails to illuminate when the ignition isturned to on, continues to flash orremains on, contact your authorizeddealer as soon as possible. A chime will sound when there is amalfunction in the indicator light. Safety belt: Reminds you to fasten your safety belt. A Belt-...

Overdrive cancel and gradeassist (if equipped): Illuminates when the overdrive function of thetransmission has been turned offand the grade assist function hasbeen turned on, refer to the Driving chapter. Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on a...

GAUGES Standard measure cluster shown, metric similar. Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, th...

Fuel gauge: Indicates approximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly when thevehicle is in motion or on a grade. The fuel icon and arrow indicateswhich side of the vehicle the fuelfiller door is located. Refer to Filling ...

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic...

System check and vehicle feature customization Press the SETUP button repeatedlyto cycle the message center throughthe following features: RESET FOR SYSTEM CHECK When this message appears, pressthe RESET button and the messagecenter will begin to cycle throughthe following systems and provide astatu...

PARK AID (Reverse sensing system–if equipped) This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and functions only when R (Reverse) gear is selected. Press RESET to turn the rear park assist off. CREATE MYKEY / MYKEY SETUP/ CLEAR MYKEY For more information refer...

AUDIO SYSTEMSAM/FM/single CD MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your prim...

MEMORY PRESETS (0–9): There are 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desired channelthen press and hold a memory preset number (0–9) until sound returns. TEXT: Press and release to display the artist and song title. While ...

the system will take you to the channel playing the desired song. Youcan save up to 20 song titles. If you attempt to save more than 20titles, the display will read REPLACE SONG? Press OK to access thesaved titles and press / to cycle through the saved titles. When the song title appears in the disp...

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. The display will read ENTER OLD PIN. Enter your current (old) PIN andwhen the system accepts your entry it will display ENTER NEW PIN.Enter your new four-digit PIN and the system will save the new PINand PIN SAVED will display. c. UNLOCK ALL CHAN...

If your vehicle is equipped with a navigation system, refer to Auxiliary input jack section in the Audio features chapter of your Navigation System supplement. Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3...

4. The portable music player must be controlled in the same mannerwhen it is used with headphones as the AIJ does not provide control(play, pause, etc.) over the attached portable music player. 5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be att...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location that is blocking the SIRIUS 威 signal (i.e., tunnel, under an overpass, dense foliage, etc). The system is working properly. When you move into ...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Turn to select fan speed. 2. R Rear defroster: Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this chapter for more information. 3. Defrost: Distributes outside air throu...

9. Temperature control: Controls the temperature of the airflow in the vehicle. 10. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed tocool down the interior of the vehicle, when used with A/C, and may alsohelp red...

During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C position, reduce blower fan speed from the highest settingand put the vehicle’s transmission into the P (Park) gear position(automatic transmission only...

10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter. 11. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time ...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (NAVIGATIONBASED – IF EQUIPPED) 1. CLIMATE: Press to control the climate control system through the touch display screen. See Touchscreen functions later in this section. 2. R Rear defroster: Press to activate/deactivate the rear window defroster. this button ...

6. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed tocool down the interior of the vehicle, when used with A/C, and may alsohelp reduce undesired odors from reaching the interior of the vehicle.Recirculated air en...

VOICE COMMANDS IN CLIMATE MODE Please refer to the Voice commands in climate mode section of the Navigation Supplement for more information on using voice commands with the climate control system. Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost) or (flo...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument p...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled b...

4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. See Message center in the Instrument Cluster section for more information. Fog lamp control (if equipped...

Flash-to-pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output.To activate: • the ignition must be in the on position, • the headlamp control is in the off, autolamps or parking lamp positionand • th...

Your vehicle may also have readinglamps within the rear dome lamp(s). Press the switches on either side ofthe dome lamp to turn on thelamps. Ambient lighting (if equipped) Illuminates footwells, storage binsand cupholders with a choice ofseveral colors. The ambient lightingcontrol is located on the ...

Replacing interior bulbs Check the operation of all bulbs frequently. Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs (2.5L/3.0L engines) High beam/low beam bulb replacement For driver side replacement of this bulb, do the following: WARNING: To red...

Low beam 6. Disconnect the electrical connector. To install, reverse the removal procedure. For passenger side replacement of the high beam bulb, do thefollowing: 1. Make sure the headlamp control is in the off position, then open thehood. 2. Reach over the front bolster. 3. Disengage the windshield...

6. Disconnect the electricalconnector. 7. Carefully pull bulb straight out ofsocket and install the new one. WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause theb...

Replacing headlamp bulbs (3.5L engine) High beam/low beam bulb replacement For driver side replacement of the high beam/low beam bulbs, do thefollowing: 1. Make sure the headlamp switch is in the off position, then open thehood. 2. Reach over the front bolster and remove the rubber bulb access cover...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers (if equipped): When the wiper control is set to any of the interval settings except the longest pause se...

Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick press and hold: thewipers will swipe three times withwasher fluid. • a long press and hold: the wipersand washer fluid will be activatedfor up to ten seconds. Courtesy wipe fe...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment Press on the rear edge of thecompartment door to open. The storage compartment may beused to secure sunglasses or asimilar object. ELECTRONIC COMPASS (IF EQUIPPED) The co...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the storage compartment. AUXILIARY POWER POINT (12V DC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet...

POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in t...

• If or is pressed during the opening operation, both windows and moon roof movement will stop. Note: The ignition must be in the off position and the accessory delay feature must be not activated in order for this feature to operate. Note: To disable this feature, contact your authorized dealer. Bo...

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror (if equipped) The interior rear view m...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

Using speed controls The speed controls are located on the steering wheel. The followingbuttons work with speed control: – SET +: Press to set a speed or to increase or decrease the set speed. CNCL (Cancel)/RSM (Resume): Press to return cancel or resume aset speed. ON/OFF: Press to turn speed contro...

For further information on the SYNC 威 system, refer to the SYNC 威 supplement. Navigation system/SYNC 威 hands free control features (ifequipped) Press control briefly until the voice icon appears on the Navigation display to use the voicecommand feature. Press to activate phone mode or answer a phone...

To close the moon roof: The moon roof is equipped with an automatic, one-touch, express closingfeature. Press and release the front portion of the control. To stopmotion at any time during the one-touch closing, press the control again. Bounce-back: When an obstacle has been detected in the moon roo...

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) Your vehicle may be equipped with a universal garage door opener whichcan be used to replace the common hand-held transmitter. Car2U 姞 Home Automation System (if equipped) The Car2U 威 Home Automation System is a universal transmitterlocated in the driver’s ...

POSITIVE RETENTION FLOOR MAT WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelets are over the retention postsand press down to lock in. Makesure that the mat...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-progr...

MYKEY 姞 The MyKey 威 feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey 威 . The key will remain restricted until MyKey 威 is cleared. Any remaining keys are referred to as an “administrato...

Clear MyKey 威 To reset all MyKeys 威 as admin keys, do the following: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed. 4. Press and hold the RESET button for two se...

4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has beenenabled. Autounlock feature The autounlock feat...

1. Place the key in the ignition andturn the ignition to the on position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the onposition to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back ...

2. Press and release again within five seconds to unlock all the doors. The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the on position. The battery saver feature will turn off the lamps 30 minutes after...

How to reprogram your integrated keyhead transmitters (IKTs) To program a new integrated keyhead transmitter yourself, refer to Programming spare keys in the SecuriLock 威 passive anti-theft system section of this chapter. Note: At least two IKTs are required to perform this procedure yourself. Illum...

the ignition is in the 1 (off) position and all vehicle doors are closed. Youmust complete Steps 1–5 within 30 seconds or the procedure will haveto be repeated. If the procedure needs to be repeated, wait a minimumof 30 seconds before beginning again. 1. Place the key in the ignition andturn the ign...

Anti-scan feature If the wrong code has been entered seven times (35 consecutive buttonpresses), the keypad will go into an anti-scan mode. This mode disablesthe keypad for one minute and the keypad lamp will flash.The anti-scan feature will turn off after: • one minute of keypad inactivity. • press...

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the samekey chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded IKT while starting the engine. Theseobjects will not cause dama...

The theft indicator will illuminate for three seconds and then go out. Ifthe theft indicator stays on for an extended period of time or flashesrapidly, contact your authorized dealer as soon as possible. Replacement of integrated keyhead transmitters (IKT) and codedkeys Note: Your vehicle comes equi...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion ofyour Integrated Keyhead Transmitter. • Unlocking the doors using the keyless entry keypad (if equipped). • Turn ignition to the on position with a valid ...

FRONT SEATS WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Tilting head restraints (if equipped) The front head restraints may have a tilting feature for extra comfort. Totilt the head restraint, do the following: 1. Adjust the seatback to an up...

Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation. Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) The lumbar control is located on theside of the seat cushion. Turn to adjust lumbar support. Adjusting the front p...

Move the control in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the control in the direction ofthe arrows to move the seatforward, backward, up or down. Power recline (if equipped) Press the control to recline theseatback forward or rearward. Using the pow...

REAR SEATS Second-row adjustable head restraints Your vehicle is equipped with outboard and center head restraints thatare vertically adjustable. WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, unt...

Center head restraint The center head restraint consistsof: • a trimmed energy absorbing foamand structure (1), • two steel stems (2), • a guide sleeve adjust/releasebutton (3), • and a guide sleeve with a pin holefor removing the head restraint(4). To adjust the head restraint, do the following: 1....

To remove the center head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustmentposition. 2. Insert and push a tool, such as a large paper clip, into the pin holelocated on the side of the guide sleeve and press the adjust/releasebutton, then pull the head...

to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety belts or child safety seats and they move forward during pre-crashbraking. The mo...

Front safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occup...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, press the releasebutton and remove the tong...

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of thec...

How to use the automatic locking mode 1. Buckle the combination lap andshoulder belt. 2. Grasp the shoulder portion andpull downward until the entire beltis pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the auto...

Safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,pull on the center button and slidethe height adjuster up...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The passenger airbag cover is a seamless design so that you cannot seethe boundary around its door. The shaded area in the illustrationrepresents the passenger airbag cover. WARNING: Do not put anything on or over the airbag cover. Placing objects on or ove...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• a readiness light and tone • and the electrical wiring which connects the components • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or...

The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind youthat the front passenger frontalairbag is disabled. The indicatorlamp is located in the center stack of the instrument panel above theradio. Note : The i...

In case there is a problem with thefront passenger sensing system, theairbag readiness light in theinstrument cluster will stay lit. If the airbag readiness light is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenge...

WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not replaced, the unrepairedarea will increase the risk of injuryin a collision. Determining if the system is...

Side-curtain airbag system WARNING: Do not place objects or mount equipment on or near the headliner at thesiderail that may come intocontact with a deploying side aircurtain. Failure to follow theseinstructions may increase the riskof personal injury in the event of acollision. WARNING: Do not plac...

How does the side air-curtain system work? The design and development of theside air curtain system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

The side air curtains are mounted to the sheet metal above the first andsecond row seats. In certain lateral collisions, the air curtain andseat-mounted side airbag on the side affected by the collision will beinflated, except that the passenger sensing system will deactivate thepassenger seat-mount...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddlerseat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced460 mm (18 inches) apart. The standardized spacing for LATCH loweranchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH at...

The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below. The tether anchors in your vehicle are located under a cover markedwith the tether anchor symbol (shown with title). The tether strap anchors in yourvehicle are in the following...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thiscondition. Do not introduce any item thicker than this under the boosterseat. Check with the booster seat manufacturer’s instructions. The importance of shoul...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. • Front-wheel drive(FWD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram) Somet...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four roadtires and sends the tire pressure readings to your vehicle. The low tirepressure warning light will turn on if the tire pressure is significantly low.Once the light is ill...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low tire pressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires, Wheels and Loading 202 2011 Fusion (fsn) ...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

Front-wheel drive (FWD) vehicles equipped with a 2.5L or 3.0Lengine can be towed with all four wheels on the ground or with the front wheels off the ground by using a tow dolly. If you are using a towdolly follow the instructions specified by the equipment provider. If youare towing with all four wh...

Front-wheel drive (FWD) vehicles equipped with a 3.5L engine can’t be towed with the front drive wheels on the ground or transmissiondamage may occur. It is recommended to tow your vehicle with the frontdrive wheels on a dolly or with all four wheels off the ground on acar-hauling trailer. All-wheel...

STARTING Positions of the ignition 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessories off. Note: In order to switch off the enginewhile the vehicle is in motion, shiftto neutral and use the brakes tobring the vehicle to a safe st...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). 2. Turn the key to 4 (start), thenrelease the key as soon as theengine begins cranking. Your vehiclehas a computer assisted crankingsystem that assists in starting theengine. After releasing the key fromthe 4 (start) ...

become very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been operating for approximately a half hour. • Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working or...

Using ABS When hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainfull steering control duri...

Switching off traction control If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the AdvanceTrac 威 system may be beneficial because the wheels are allowed to spin. This will restore fullengine power and will enhance momentum through the ob...

WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. AUTOMATIC TRANSMISSION OPERATION Understanding the gearshift positions of the 6–speed automatictransmission equipped with a 2.5L I4 eng...

Overdrive cancel with grade assist is designed to provide optimal gearselection in hilly terrain or mountainous areas. It is recommended thatyou return to D (Drive) on flat terrain to provide the best fuel economyand transmission function. To return to D (Drive), press the transmission control switc...

Understanding your SelectShift Automatic™ transmission (SST)gearshift lever This vehicle may be equipped with a SelectShift Automatic™transmission (SST) gearshift lever. SST is an automatic transmission withthe ability for the driver to change gears up or down (without a clutch)as desired. By moving...

Initially when moving the lever to the manual mode (M), the instrumentcluster will show the current selected gear and the SST light willilluminate. Only by moving the lever in the forward (-) or backward (+)position will the transmission utilize the manual mode for select shifting. To manually downs...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is fully pressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to thefloor, then...

Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) Reverse 1. Make sure that your vehicle is at a complete stop before ...

3. Turn the ignition off. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Removing the key Turn the ignition to the off position, and remove the key. REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensin...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system,located on the trunk, provides avideo image which appears in therear view mirror or on thenavigation screen (if equipped), ofthe area behind the vehicle. It addsassistance to the driver whilereversing or reverse parking thevehicle.To us...

BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer ...

BLIND SPOT INFORMATION SYSTEM (BLIS 姞 ) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) The BLIS 威 is a convenience feature that aids the driver in assessingwhether a vehicle is within an areaon either side of the vehicleextending rearward from the outsidemirrors to approximately 10 feet(three meters) ...

Cross traffic alert (CTA) system operation The CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backing out of a front-in parkingspot. It sounds a series of tones and flashes the BLIS 威 indicator found on the exterior mirror on the side of the approa...

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed to vehicle on left] ). CTA detection limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting theblind spot ...

CTA and Reverse Sensing System (RSS) interaction CTA works along with the Reverse Sensing System (RSS) (if equipped).Become familiar with the warning tones of both systems. BLIS 威 -CTA on/off and disable operation The BLIS 威 and/or the CTA can be turned off via the message center. Turning the BLIS 威...

WARNING: Just prior to the system recognizing a blocked condition and alerting the driver, the number of missed objects will increase. To help avoid injuries, NEVER use the BLIS 威 as a replacement for using the side and rear view mirrors and looking overyour shoulder before changing lanes. BLIS 威 is...

ALL-WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time all-wheel drive (AWD)system. The AWD system is an active system, meaning it not onlyresponds to wheel slip between the front and rear axles but also has theability to anticipate wheel slip and transfer torque to...

When driving through water, determine the depth; avoid water higherthan the bottom of the wheel rims (if possible) and proceed slowly. If theignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Dry...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

U.S. Ford and Lincoln vehicle customers who require RoadsideAssistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56 km). To obtain reimbursementinformation, ...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

To remove a fuse use the fuse puller tool provided on the fuse panelcover. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Driver smart window motor 2 15A Brake on/off switch, Centerhigh-mounted stop lamp 3 15A Not used (spare) 4 30A Not used (spare) 5 10...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 41 G8VA relay Backup lamps 42 — Not used 43 G8VA relay A/C clutch 44 — Not used 45 15A** Injectors 46 15A** PCM 47 10A** General powertrain components,A/C clutch relay, Backup lamps 48 15A** Ignition coils 49 15A** Emissions related powertrainco...

(TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing ofthe flat tire, have the authorized dealer inspect the TPMS sensor fordamage. WARNING: The use of tire sealants may damage your tire pressure monitoring system...

• Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to im...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

Tire change procedure WARNING: To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side andend of the vehicle) to the tire being changed. WARNING: If the vehicle slips off the j...

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. 8. Unblock the wheels. Stowing the wheel and jack 1. Fully collapse the jack and place it back in the storage area in the...

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the rotor to the hub are secured so they do ...

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+) terminal of the assisting battery. 3. Connect the negative (-) cable tothe negative (-) terminal of theassisting battery. 4. Make the fi...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

Regular cleaning and conditioning will maintain the appearance of theleather. Cleaning For dirt, use a vacuum cleaner then use a clean, damp cloth or softbrush. For routine cleaning, wipe the surface with a soft, damp cloth. For morethorough cleaning, wipe the surface with a mild soap and water solu...

FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its finishes. These qualityproducts have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the style andap...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it with the pro...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.5L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake/Clutch fluid reservoir 5. Transmission fluid dipstick (automatic transmission only) 6. Battery 7. Power distribution box 8. Air filter assembly 9. Cool...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normaloperating range. • 2.5L I4 engine • 3...

• 3.5L V6 engine If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above this markmay cause engine damage. If the engine is overfilled, some oil mustbe removed from the engine by anauthorized dealer. 7. Put the di...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol conforms to thecurrent engine and emission system protection standards and fue...

BATTERY Your vehicle is equipped with aMotorcraft 威 maintenance-free battery which normally does notrequire additional water during itslife of service. If your battery has acover/shield, make sure it isreinstalled after the battery hasbeen cleaned or replaced. For longer, trouble-free operation,keep...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine coolantreservoir (depending upon application). • Refer to scheduled maintenance information for serv...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants mayharm your engine’s cooling system. The use of an improper coolantmay harm engine and cooling system components and may void thewarranty. Refer to Maintenance product...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling ...

The use of leaded fuel is prohibited by law and could damage yourvehicle. Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle perform...

“Premium” unleaded gasoline is not recommended for vehicles designedto use “Regular” unleaded gasoline because it may cause these problemsto become more pronounced. If the problems persist, see yourauthorized dealer. FFV engines If you experience starting, rough idle or hesitation driveability probl...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

POWER STEERING FLUID Refer to scheduled maintenance information. • 3.5L V6 engine only 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area between H and C). 2. While the engine idles...

BRAKE/CLUTCH FLUID Brake and clutch (if equipped) systems are supplied from the samereservoir. • 2.5L engine • 3.0L/3.5L engines The fluid level will drop slowly as the brakes wear, and will rise when thebrake components are replaced. Fluid levels between the MIN and MAXlines are within the normal o...

Changing the air filter element • 2.5L I4 engine • 3.0L V6 engine • 3.5L V6 engine 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. Maintenance and Specifications 328 2011 Fusion (fsn) Owners Guide, 3rd PrintingUSA (fus)

• 2.5L I4 engine • 3.0L V6 engine • 3.5L V6 engine 3. Remove the air filter element from the air filter housing. Maintenance and Specifications 329 2011 Fusion (fsn) Owners Guide, 3rd PrintingUSA (fus)

4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This could causefilter damage and allow unfiltered air to enter the en...

Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking parts and prevent corrosion. Removing vehicle from storage When your vehicle is ready to come out of storage,...

MOTORCRAFT PART NUMBERS Component 2.5L I4Engine 3.0L V6 Engine 3.5L V6 Engine Air filterelement FA-1785 FA-1786 FA-1884 Battery BXT-96R-500 BXT-96R-500 BXT-96R-500 Oil filter FL-910S FL-500-S FL-500-S Spark plugs 1 Cabin air filter FP-67 FP-67 FP-67 1 For spark plug replacement, see your authorized ...

• 3.5L V6 Engine 1. Short drivebelt is on first pulley groove closest to engine. 2. Long drivebelt is on second pulley groove farthest from engine. IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code 6–speed manual transmission (G6M) 6 6–speed automatic transmission (6F35) W 6–speed automatic transmission...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Remote start • Protective seat covers* • Vehicle security systems • Back up camera* • Wheel locks • Keyless entry keypad • Vehicle tracking and recovery* • Bumper mounted parking sensors* • Locking fuel cap capless fuel system *Ford Licensed Accessories (FLA) are warranted by the acc...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

different specifications and performance features. That’s why it’simportant to rely upon your dealership to properly diagnose and repairyour vehicle. Ford Motor Company has recommended maintenance intervals forvarious parts and component systems based upon engineering testing.Ford Motor Company reli...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service? Factory-trained technicians Service technicians participate in extensive factory-sponsoredcertification training to help them become experts on the operati...

NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service interval. You shouldperform the engine oil change as indicated by the message center. Themessage center will display ENGINE OIL CHANGE SOON or OILCH...

Oil Change S ervice Interval* 1 23456789 1 0 1 1 1 2 1 3 1 4 1 5 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • •••••••••••••• Inspect wheels and related components for abnormal noise, wear , looseness or drag • •••••••••••••• Perform multi-po...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and filter as indicated by messagecenter and perform services listed in the NormalScheduled Maintenance chart (except Fiesta) Inspect f...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components forabnormal noise, wear, looseness or drag– Rotate tires,...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axlesare lubricated for life. These fluids are not...

ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km)(whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE...

A Accessory delay ..........................80 AdvanceTrac ..............................216 Airbag supplemental restraintsystem ........................146, 155, 158 and child safety seats ............148description ..............146, 155, 158disposal ....................................161driver a...

V Vehicle Identification Number(VIN) ..........................................340 Vehicle loading ..........................201 Ventilating your vehicle ...........212 W Warning lights (see Lights) .......12 Washer fluid ..............................293 Water, Driving through .............248 Wind...