Ford 2011 Flex v.2- Manuals

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions couldresult in ...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”) only to help provide you with the directions, ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Powertrain malfunction/reducedpower: Illuminates when a powertrain or a AWD fault has beendete...

AdvanceTrac 威 /traction control off: Illuminates when the AdvanceTrac 威 /traction control has been turned off. Refer to the Driving chapter for more information. Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressur...

TIMER Timer displays the trip elapsed drive time. To operate, do the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET until the timer resets. Blank Screen The message center display will be blank after cycling t...

EASY ENTRY This feature automatically moves the driver’s seat backwards for easyexit/entry from the vehicle. Press RESET to turn it off or on. REAR PARK AID (if equipped) This feature sounds a tone to warn the driver of obstacles near the rearbumper, and functions only when R (Reverse) gear is selec...

AUDIO SYSTEMS AM/FM CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary re...

CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded, NO DISC will appear in thedisplay. LOAD:For a single CD system– This control is not operational. To load aCD, simply insert the disc, label side up...

TEXT: Press and release to display the artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH) and Category (CA). In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT...

titles, the display will read REPLACE SONG? Press OK to access thesaved titles and press SEEK to cycle through the saved titles. When the song title appears in the display that you would like toreplace, press OK. SONG REPLACED will appear in the display. b. DELETE A SONG: Press OK to delete a song f...

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. The display will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accepts your entry it will displayENTER NEW PIN. Enter your new four-digit PIN and the system willsave the new PIN and PIN SAVED will display. c. UNLOCK A...

Extra Features AUX: Press repeatedly to cycle through LINE (auxiliary audiomode), SYNC 威 (if equipped) and FES modes (if equipped).For location and further information on auxiliary audio mode, refer to Auxiliary input jack later in this chapter. If your vehicle is equipped with SYNC 威 , refer to the...

The auxiliary input jack provides away to connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To achieve optimalperformance, please observe thefollowing instructions whenattachi...

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also to charge devices ifthey support this feature. Forfurther information on this feature,refer to Accessing and using your USB port in the SYNC 威 supple...

Audio system warranty and service Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and folder structureas follows: • There are two diffe...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is...

Note: The system goes into dual play mode when it is turned on. Audio from the DVD system will not play over the rear two speakers until dualplay mode is turned off. When dual play mode is turned on, the audiosound plays over the front two speakers until dual play mode is turnedoff. Note: Each headr...

DVD player controls 1. / (Play/Pause): Press to play or pause a CD, DVD or flash/thumb drive track.2. (Stop): Press to stop the current DVD, CD/MP3, or flash/thumb drive track.3. (Eject): Press to eject a disc from the DVD system. 4. MENU: When playing a DVD, press MENU to enter the DVD disc (root) ...

Remote control Unless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the player.Ensure that there are no obstructions between the remote and player.Press the MON A B control to select either Monitor A or Monitor B. Note: Each h...

2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a menu, the left and right cursor controlsdecrease and increase the display brightness, and the left and rightcursor controls advance to the next or previous station when accessingthe radio tuner in...

15. MEDIA for Monitor A: In Dual Play mode, press MEDIA repeatedly to select from the possible media sources: (Monitor A, Monitor B, AM,FM1, FM2, SR1, SR2, SR3 (satellite radio, if equipped), Disc, Jukebox (ifequipped) and SYNC 威 (if equipped). The selected media type will display on the screen. Whe...

Battery replacement Batteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails tocontrol the DVD player. Remove the screw and unlatch the battery cover to access the batteries. The remote control unit uses two AAA batteries which...

where indicated on the left and right hand sides of the system. Refer to Wired Headphones following. To install the batteries, remove the screw on the cover and removethe cover. Then, gently lift the topof the cover away from the housingto expose the battery compartment. When replacing the batteries...

Ensure that the headphones are turned off when not in use. Afterapproximately one minute of not being in use (no infrared signal isreceived), the wireless headphones will automatically turn off. They willalso turn off after two hours of continuous use as a power save feature.If this happens, simply ...

Dual Play: Dual play is when the rear seat passengers choose to listen to a different playing media than the front seat passengers. With theDVD and rear seat controls turned on, the rear seat passengers maychoose to listen to: Monitor A, Monitor B, AM, FM1, FM2 SR1, SR2, SR3(satellite radio, if equi...

Radio interaction: If your vehicle is equipped with a non-touchscreen audio system, you can press AUX on the radio repeatedly until DVDappears in the display. Then, press MENU to access HEADPHONESON/OFF, REAR ZONE CONTROL ON/OFF and other options. Turn theTUNE control to select ON/OFF for HEADPHONES...

Aspect ratio (TV display type) This screen allows you to select theviewing size and shape of the videodisplayed on the LCD screen. This isdisc dependent feature.To access: 1. Press SETUP on the remote to access the menu options. 2. Press / to ’highlight’ the monitor icon. (A disc will appear beneath...

2. Press / to ’highlight’ the monitor icon. (A disc will appear beneath the icon signifying it is the current selection.) 3. Press to select and enter the OSD language menu. 4. When OSD Lang is highlighted, press to access the menu. 5. Press / to select from all available languages. 6. When the desi...

4. Press / to chose from Sharpness, Brightness, Contrast, Gamma (Color), Hue, Saturation and Luma-Delay. General setup — screen exit To exit the setup screen: 1. Press / to ’highlight’ the “X” icon. (A disc will appearbeneath the icon signifying it is thecurrent selection.) 2. Press ENTER on the rem...

General information Note: DVDs are formatted by regions. US and Canada systems canonly play region 1 DVDs and Mexicosystems can only play region 4DVDs. Systems sold in vehiclestargeted for other parts of the worldwould have different regions. If aplayback problem is encountered,please ensure that yo...

Safety information WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of the v...

Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where they will not be stepped on or interfere with the operationof seats and/or compartments.Disconnect video games and video equipment power cords and/or c...

Humidity and moisture condensation Moisture in the air will condense in the DVD player under extremelyhumid conditions or when moving from a cold place to a warm one.Moisture condensation may cause damage to the DVD and/or player. Ifmoisture condensation occurs, do not insert a CD or DVD into thepla...

SINGLE ZONE CLIMATE CONTROL WITH REAR PASSENGERCOMPARTMENT CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog andthin ice. The system will automatically provide outside air to reducewindow fogging....

Operating tips • To reduce fog build-up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build-up inside the vehicle: do not drive with thesystem off or with recirculated air engaged. • Do not put objects under the front seats that will interfe...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS AND REAR PASSENGER COMPARTMENTCLIMATE CONTROL (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Front fan speed control: Press to increase the fan sp...

• : Distributes air through the instrument panel vents. • : Distributes air through the instrument panel vents, floor vents and rear seat floor vents. • : Distributes air through the floor vents and rear seat floor vents. 4. A/C: Press to activate/deactivate air conditioning. Use with recirculated a...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (NAVIGATIONBASED–IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Climate: Press to control the climate control system through the touch display screen. See Touchscreen...

TOUCHSCREEN FUNCTIONS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument cluster chapter. Front Zone – Press to activate the touchscreen controls for the front climate system. Temperature – Press the up and down arrows on the left side of the ...

Max A/C – Distributes recirculated air through the instrument panel vents to cool the vehicle. This re-cooling of the interior air is moreeconomical and efficient. Recirculated air may also help reduceundesirable odors from entering the vehicle. Press MAX A/C again fornormal operation. Rear Zone Pow...

• To improve the A/C cool down, drive with the windows slightly openfor 2–3 minutes after starting the vehicle or until the vehicle has“aired out.” • A small amount of air may be felt from the floor vent regardless of theair distribution setting that is selected. In extremely cold temperatures, to m...

AUXILIARY CLIMATE CONTROL 1. Fan speed: Turn to select the desired fan speed. 2. : Distributes air through the rear vents. 3. : Distributes air through the rear vents and rear-seat floor vents. 4. : Distributes air through the rear floor vents. 5. Temperature selection: Turn to select air temperatur...

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice. The ignition must be on to operate the rear window defroster. The rear defroster turns off automatically after 10 minutes or when theignition is turned of...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on/off control ofthe exterior lights normallycontrolled b...

3. Turn the ignition on and then back to off. 4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. You can also use the message center to program the autolam...

Flash-to-pass Pull and release to activate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position, • the headlamp control is in the off, autolamps or parking lamp positionand • the transmission must be out of th...

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmerswitch from the full dim position to the full dome/on position to reset.This will ensure that your displays are visible under all lightingconditions. AIMING TH...

5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise (to adjust up).The horizontal edge of the brighterlight should touch the horizontalreference line. 6. Close the hood and turn off the lamps. HORIZONT...

Your vehicle may have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps. Your vehicle may have second rowlamps located within the grabhandles. Press the lens up to turnon the lamps. Ambient lighting (if equipped) Illuminates footwells and...

Function Number of bulbs Trade number Map lamp 2 12V6W Dome/reading lamps 6 578 To replace all instrument panel lights - see your authorized dealer.*To replace these lamps - see your authorized dealer. Replacing interior bulbs Check the operation of all bulbs frequently. Replacing exterior bulbs Che...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Normal speed operation of rearwiper. 1 — Intermittent operation of rearwiper. 0 (off) — Rear wiper and washer off. For rear wash cycle, rotate (and hold as de...

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamp. Slide-on-rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted before moving it backtoward the...

CLOCK (IF EQUIPPED) Press the right (+) control to movethe time display forwards. Press the left (-) control to movethe time display backwards. ELECTRONIC COMPASS The compass heading is displayed in the center integrated display (CID). The compass reading may be affected when you drive near largebui...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

Second row center console features (if equipped) The second row center consoleincorporates the following features: • Flip forward armrest to provide aflat load floor • Utility compartment • Cupholders • Refrigerator unit (if equipped) inthe utility compartment. Refer to Console refrigerator/freezer....

Refrigerator: Briefly press and hold the COOL side of the control.The indicator light on the cool sideof the switch will illuminate and theindicator light on the freeze side willglow when the refrigerator is active.When in cool mode the temperaturewill cool to approximately 41°F(5°C). Briefly press ...

WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the window switchesto open and close windows. • Press down (to the first detent)and hold the switch to open. •...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. Accessory delay With accessory delay, the radio, power windows, an...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control,located toward the front of thedriver’s door, to adjust accelerator and brake pedal. • Pr...

Using speed control The speed controls are located on the steering wheel. The followingbuttons work with speed control: RESUME: Press to resume a set speed. SET +: Press to increase the set speed. SET –: Press to decrease the set speed. OFF/ON: Press to turn speed control off or on. Setting speed co...

Increasing speed while using speed control To set a higher speed: • Press and hold SET + until you get to the desired speed, then release.You can also use SET + to operate the tap-up function. Press andrelease SET + to increase the vehicle set speed in 1 mph (1.6 km/h)increments. • Use the accelerat...

Navigation system hands-freecontrol features (if equipped) Press and hold control briefly until the voice icon appears on the navigation display to use thevoice command feature. Press to complete a voice command. For further information on thenavigation system, refer to the Navigation System supplem...

To vent the multi-panel Vista Roof™: Press and release the TILT control, the roof will move to the vent position automatically. Press theswitch again to stop the roof. Pull and hold the TILT control to close theroof. The multi-panel Vista Roof™ has a built-in sliding shade that can bemanually opened...

Programming Do not program HomeLink 威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the accessory position for programming and/or operation of the HomeLink 威 . It is also recommended that a new battery be placed in the hand-heldtransmitter ...

6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat thissequence a third time to complete the p...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

POSITIVE RETENTION FLOOR MAT WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelets are over the retention postsand press down to lock in. Makesure that the mat...

WARNING: Make sure that the liftgate door is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive withthe liftgate door open, keep the vents open so outside air comes intothe vehicle. POWER LIFTGATE (IF EQU...

To power open the liftgate withoutside liftgate control button: 1. To open, unlock the liftgate withthe integrated keyhead transmitteror power door unlock control. 2. To open the liftgate, push thecontrol button located in the top ofthe liftgate pull cup handle. Note: For the best performance allow ...

Obstacle detection: The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system will reverse to full open whenit detects an obstacle. A chime will sound three times when an obstacleis detected as the liftgate begins to reopen. Once the obsta...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and the transmitter portionfunctions as the remote entrytransmitter. Vehicles with a powerliftgate will have a four-button...

MYKEY™ The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is cleared. Any remaining keys are referred to as an“administrator key” o...

Create a MyKey™ To program MyKey™ on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey™ into the ignition. Turnthe ignition on. Use the message center buttons to do the following: 1. Press SETUP until PRESS RESET TO CREATE MYKEY is displayed. 2. Press and release...

Clear MyKey™ To reset all MyKeys™ as admin keys do the following: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed. 4. Press and hold the RESET button for two secon...

3. Follow Steps 1-4 in the Create a MyKey™ section. Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or ADMIN KEYS PROGRAMMED that is displayed in the MyKey™ systemstatus menus will include the remote start system as an additional key inthe total count. See the Check MyKey™ system status se...

Press to automatically move the driver seat, power mirrors and adjustable pedals to the desired memory position. The mirrors will moveto the programmed position and the seat will move to the easy entryposition. The seat will move to the final position when the key is in theignition (if easy entry fe...

To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. Note: Do not wipe off any grease on the battery terminals on the backsurface of the circuit board. 2. Remove the old battery. Note: Please refer to local regulations when disposi...

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theintegrated keyhead transmitter or the keyless entry system keypad isused to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the on position, or • ...

SECURICODE™ KEYLESS ENTRY SYSTEM The keypad is invisible until touched and then it lights up so you can seeand touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter yourentry code more slowly. You can use the keyless entr...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, touch the 1 • 2 on the keypad ...

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the offposition, the indicator will flashonce every two seconds toindicate the SecuriLock 威 system is functioning as a theftdeterrent. • When the ignition is in the on position, the in...

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keepthe ignition in the 3 (on) position for at least three seconds, but no mor...

Arming the system When armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash theturn signal lamps and will sound the horn. The system is ready to arm whenever the key is in the off position, or isremoved from the ignition. Either of ...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion ofyour integrated keyhead transmitter (IKT). • Unlock the doors by using your keyless entry pad. • Turn ignition on with a valid SecuriLock 威 key or IKT. •...

FRONT SEATS WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Tilting head restraints (if equipped) The front head restraints may have a tilting feature for extra comfort. Totilt the head restraint, do the following: 1. Adjust the seatback to an up...

Move the control in the directionsshown to move the seat forward orbackward. Press the control to recline theseatback forward or rearward. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the controlto adjust...

A position can only be recalled when the transmission gearshift is in Park(automatic transmission). A memory seat position may be programmedat any time. The memory seat positions are also recalled when you press your remoteentry transmitter (unlock) control and the transmitter is programmed to a mem...

Easy entry/exit feature (if equipped) This feature automatically moves the driver’s seat rearward 2 in (5 cm)when: • the transmission is in N (Neutral) or P (Park) • the key is removed from the ignition The seat will move to the original position when: • the transmission is in N (Neutral) or P (Park...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting second row bucket and bench seat back Lift the handle to adjust seatback.Using same control will fold theseatback flat. Note: For the bench seat only, make sure the center safe...

Ensure that the rear latch hooks areproperly engaged with the floorstriker. Note : Ensure that the seat and seatback are latched securely inposition. Keep floor area free ofobjects that would prevent properseat engagement. WARNING: Do not adjust or release the seat floor latch while vehicle is in mo...

To operate the heated seats: • Press the button located on therear of the floor console once toactivate high heat. • Press twice to activate low heat. • Press a third time to deactivate. The indicator light on the control will illuminate when activated. For lowheat, one light will be lit; for high h...

4. Release the cushion latches by pulling the number 2 strap whilepulling on the strap located at the top of the seatback to tumble the seatall the way into the tub in the floor. Note: Do not use the seat anchors as cargo tie downs. Note: Do not use the third row seatback as a load floor when thesea...

1. Unlatch and lift the seat out of the tub in the floor by squeezing andpulling up on the handle. Once the seat is at a vertical position, push theseat over, letting it fall onto the latches. 2. To return the seatback to uprightposition, pull the number 1 strap,then while holding the number 1strap,...

Note: In order to allow the seat to complete the stowed position, do not place objects under the seat before stowing. Remove all objects from theseat and stowage tub. Note: In the unlikely event that the third row power seat stops prematurely, or travels to an unexpected position, press the FOLDbutt...

SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash s...

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbaginflation energy. A lower, less forceful energy level is provided for morecommon, moderate-severity impacts. A higher energy level is used forthe most severe impact...

The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint us...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, driver seatposition sensor, and front passenger sensing system. In addition, theRCM also monitor...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

Safety belt locking modes All safety restraints in the vehicle are combination lap and shoulderbelts. The driver safety belt has the first locking mode and the frontoutboard passenger and rear seat safety belts have both types of lockingmodes described as follows: Vehicle sensitive mode This is the ...

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the sa...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasingthe risk of injury. Do not modify the front end of the vehicle. Children and airbags Children must alway...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• diagnostic module. • the electrical wiring which connects the components. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this chapter. Th...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same lightfor front and side airbag system)will either flash or stay lit. • The readiness light will notilluminate immediately after ignition is turned on. • A series of five beeps will be heard. The to...

How does the side airbag system work? The design and development of the side airbag system includedrecommended testing procedures that were developed by a group ofautomotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofin...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with the syst...

Important child restraint precautions WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the vehicle.Failure to follow these instructions and guidelines may result in ani...

Recommendations for Safety Restraints for Children Child size, height, weight, orage Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap whichextends from the back of the child safety seat and hooks to an anchoringpoint called the top tether anchor. Tether straps are available as anaccessory for many older safety seats. Conta...

• 2nd row bench (60/40) • 3rd row Note : The cargo tie-downs at the rear edge of the floor are nottether anchors. 3. Clip the tether strap to theanchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision. 4. Tighten the ...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thiscondition. Do not introduce any item thicker than this under the boosterseat. Check with the booster seat manufacturer’s instructions. The importance of shoul...

NOTICE TO CROSSOVER VEHICLE OWNERS Crossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on streets, highwaysand off-road. Crossover vehicles arenot designed for cornering at speedsas high as passenger cars any morethan low-slung sports cars ar...

VEHICLE CHARACTERISTICS All-wheel drive (AWD) system (if equipped) Your vehicle may be equipped with a full-time all-wheel drive (AWD)system. With the AWD option, power will be delivered to the frontwheels and distributed to the rear wheels as needed. This increasestraction which may enable you to s...

U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give youthe following information about tire grades exactly as the governmenthas written it. Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe ...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

WARNING: Age Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.) the tires experience throughout their lives.In general, tires should be replaced after six years regardless of treadwear. However, heat cau...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Companymay af...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four roadtires and sends the tire pressure readings to your vehicle. The low tirepressure warning light will turn on if the tire pressure is significantly low.Once the light is ill...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low tirepressurewarning light Possiblecause Customer action required Flashing warninglight Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For adescription of how the systemfunctions under these conditio...

SNOW TIRES AND CABLES/CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle cont...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, thenthe load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now yo...

WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle control, vehicle rollover and personal injury. Powertrain Maximum GCWR - lb (kg) Maximum Trailer Wei...

3. Attach the trailer to the vehicle without the weight distributing barsconnected. 4. Measure the height of the top of the front wheel opening on thefender a second time, this is H2. 5. Install and adjust the tension in the weight distributing bars so thatthe height of the front fender is approxima...

Trailer brake controller connector (if equipped) The trailer brake controllerconnector is located under theinstrument panel above the brakepedal. Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. Do...

• It is recommended to select the L (Low) or M (Manual) gear positionwhen additional engine braking is needed. In situations such asprolonged downhill driving on steep grades (i.e., driving inmountainous areas), additional engine braking is needed to reduce theload on the vehicle’s regular brake sys...

Front-wheel drive (FWD) vehicles can be towed with all four wheels on the ground or with the front wheels off the ground by using a towdolly. If you are using a tow dolly follow the instructions specified by theequipment provider. If you are towing with all four wheels on the ground,refer to the tow...

STARTING Positions of the ignition 1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and allelectrical accessories off withoutlocking the steering wheel. To lockthe steering wheel, remove the keythen turn the steering wheel. 2. Accessor...

How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment, your engine blockheater will use .4 to 1.0 kilowatt-hours of energy per hour of use. Yourfactory installed block hea...

Brake assist The brake assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and uses theABS system to achieve maximum braking pressure. Once a panic brakeapplication is detected, the system will remain activated as long as thebra...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released....

• Entering a paved road from a gravel road, or vice versa • Cornering while towing a heavily loaded trailer (refer to Trailer towing in the Tires, Wheels and Loading chapter). Roll Stability Control™ (RSC 威 ) Roll Stability Control™ (RSC 威 ) may help to maintain roll stability of the vehicle during ...

During trailer sway control events, the stability control light in theinstrument cluster will flash momentarily. The cluster message centerwill also display TRAILER SWAY REDUCE SPEED . In some cases when trailer sway is detected, the vehicle speed is too high and may beat or above a speed at which t...

If the steering wanders or pulls equipped with either EPS or hydraulicsteering system, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper vehicle alignment A high crown in the road or high crosswinds may al...

-The grade assist lamp in the instrument cluster will not be illuminated. -The transmission will operate in gears one through six. Understanding your SelectShift Automatic™ Transmission (SST)(if equipped) This vehicle may be equipped with aSelectShift Automatic™transmission (SST) gearshift lever.SST...

Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) The message center display in the instrumen...

Conditions in which the system may not work: • Something passes between the front bumper and the space such as apedestrian or cyclist • The edge of the neighboring parked vehicle is high from the groundsuch as a bus, tow truck or flat bed truck Automatic search for parking space To start, press the ...

Automatic steering into parking space Automatic steering is activated when you stop the vehicle, remove yourhands from the steering wheel and select the R (Reverse) gear. Be surethe steering wheel motion is not obstructed by any objects. The vehiclewill steer itself from this point on as you follow ...

Troubleshooting Why isn’t APA searching for a parking space? • You may have deactivated the AdvanceTrac 威 system. • One of the doors (except the driver’s door) may not be securelyclosed. Why doesn’t APA offer a particular parking space? • Something may be contacting the front bumper or side sensors....

• One of the parked vehicles has a high altitude attachment (i.e. saltsprayer, snow plow, moving truck high bed, etc.) High altitudeattachments may not be detected by the system. • The parking space length or parked objects position have changedafter the vehicle has passed the parking space. • The t...

Note: The AWD OFF message may also be displayed in the message center if the AWD system has overheated and defaulted to front-wheeldrive. This condition may occur if the vehicle was operated in extremeconditions with excessive wheel slip, such as deep sand. To resumenormal AWD function as soon as po...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the engine, transmission, AWD system components or axles aresubmerged in water, their fluids should be...

Maintenance and modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on: Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio i...

Should your vehicle shut off after a collision due to this feature, you mayrestart your vehicle by doing the following: 1. Turn the ignition switch to the off position. 2. Turn the ignition switch to the on position. In some instances the vehicle may not restart the first time you try torestart and ...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — Natural Natural 30A Green Green Green Pink Pink 40A — — Orange Green Green 50A — — Red Red Red 60A — — Blue Yellow Yellow 70A — — Tan — Brown 80A —...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 46 7.5A Occupant classification sensor(OCS), Passenger airbagdeactivation indicator (PADI) 47 30A Circuit Breaker Power windows 48 Full ISO relay Delayed accessory relay Power distribution box The power distribution box is located in the engine ...

Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. To restore the full functionalityof the monitoring system, all road wheels equipped with tire pressuremonitoring sensors must be mounted on the vehicle. Have a flat serviced by an authoriz...

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remov...

1. Block the diagonally oppositewheel. 2. Remove wheel cover (ifequipped) with the lug wrench tipand loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack...

4. Insert the straight end of the jackretention bracket through the eyeletof the angled bracket and swing theretention bracket over the jack. Withthe jack in place, place the loopedend of the retention bracket overthe threaded stud in the trunk floorand secure it with the plastic wingnut. If you are...

• Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle. Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operati...

• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation. What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stageswith the temporary mobility kit: • In the first stage, the tire will be reinfla...

4. Plug the power cable into the 12Vpower point in the vehicle. 5. Remove the warning sticker found on the canister and place it on thetop of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) . 7. Turn dial (1) counterc...

tire pressure has to be checked with the compressor in the OFFposition to get the correct tire pressure reading. WARNING: Do not stand directly over the temporary mobility kit while inflating the tire. If you notice any unusual bulges or deformations in the tire’s sidewall during inflation, stop and...

4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jamb area.Pressing the deflation button nearthe sealant canister removes airfrom the tire. Note: The tire pressure has to be checked with the compressor in theOFF position to get the correc...

Removal of the sealant canister from the temporary mobility kit 1. Unwrap the clear tube from thecompressor housing. 2. Press the button located on thetemporary mobility kit compressorhousing below the canister whilepulling up on the sealant canister. Installation of the sealant canister to the temp...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 100 miles (160 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.). Bolt size Wheel lug nut torque* ft-lb N • m 1/2-20 UNF 100 135 * Torque specifications are for nut and bolt t...

5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the pos...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with...

3.5L V6 EcoBoost™ engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar ...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft 威 Premium Windshield Washer Concentrate (ZC-32-A) in the U.S., or Premium Quality Windshield Washer Fluid [CXC-37-(A, B,D, or F)] in Canada, available from your authorized dealer. Thiswasher fluid contains special soluti...

WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spill...

WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance ofthe side airbag in a collision. LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH 姞 EDITION) For King Ranch 威...

• Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather. • Do not spill coffee, ketchup, mustard, orange juice or oil-basedproducts on the leather as they may permanently stain the leather. • Do not use household cleaning products, alcohol soluti...

FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its finishes. These qualityproducts have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the style andap...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specificat...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

3.5L V6 EcoBoost™ engine 1. Engine coolant reservoir 2. Brake fluid reservoir 3. Battery 4. Power distribution box 5. Air filter assembly 6. Automatic transmission fluid dipstick (out of view) 7. Engine oil dipstick 8. Engine oil filler cap 9. Windshield washer fluid reservoir Maintenance and Specif...

Engine shield Some vehicles may be equipped with an aero-shield under the engine.This shield needs to be removed for service, including oil and filterchanges. It is secured with four quick release fasteners. WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold wea...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil ...

3. The wiper arm has a snapretention feature to receive a crosspin from the wiper blade structure.Grip tightly and press on thearm/blade joint from beneath andseparate the blade from the arm.Avoid rotating the wiper bladestructure and trapping your lefthand between the arm and blade. 4. Attach the n...

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not...

Engine oil and filter recommendations 3.5L V6 engine Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol conforms to thecurrent engine and emission system protection st...

3.5L V6 EcoBoost™ engine Look for this certificationtrademark. Use SAE 5W-30 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and fueleconomy re...

BATTERY Your vehicle is equipped with aMotorcraft 威 maintenance-free battery which normally does notrequire additional water during itslife of service. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, k...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine coolantreservoir (depending upon application). • Refer to scheduled maintenance information for serv...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. DO NOT MIX recycled coolant and new (unused) coolant together in the vehicle. Mixing of enginecoolants may harm your engine’s cooling system. The use of animproper coolant may harm engine and co...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reservoir.If you removed the radiator cap in an ...

• NEVER increase the coolant concentration above 60%. • A coolant concentration of 60% will provide improved freezepoint protection. Increased engine coolant concentrationsabove 60% will decrease the overheat protectioncharacteristics of the engine coolant and may cause enginedamage. • If available,...

WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperaturesreduce. The air conditioning may also cycle on and off during severe operatingconditions to protect overheating...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling ...

Octane recommendations 3.5L V6 engine Your vehicle will run normally on 87 octane regular fuel. Premium fuelwill provide improved performance. 3.5L V6 EcoBoost engine Your vehicle is designed to run on regular fuel with an octane rating of87 or higher. For best overall performance, premium fuel with...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the right fuel section. Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have ru...

1. After lifting the carpeted floorpanel, locate the white plasticfunnel. It is attached to the rear,lower edge of the spare tirecompartment. 2. Slowly insert the funnel into theEasy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container.4. When done, clean the funnel or proper...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

C. Remove the bolt cover (ifequipped). D. Remove two bolts that attach the air filter assembly to the front ofthe vehicle (2). E. Loosen the clamp holding the air filter assembly to the rubber hose(1). F. Remove the harness retaining clip by pulling up (3). Do notdisconnect the sensor (4). G. Withou...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft 威 part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/...

4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This could causefilter damage and allow unfiltered air to enter the en...

Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking pa...

MOTORCRAFT PART NUMBERS Component 3.5L V6 Engine 3.5L V6 EcoBoostEngine Engine air filterelement FA-1884 FA-1884 Battery BXT-65-650 BXT-65-750 Oil filter FL-500-S FL-500-S Spark Plugs SP-411 1 SP-512-A 1 1 For spark plug replacement, see your authorized dealer. Refer to scheduled maintenance informa...

ENGINE DATA Engine 3.5L V6 engine 3.5L V6 EcoBoost™ engine Cubic inches 214 214 Fuel See Octane recommendations earlier in this chapter. See Octane recommendations earlier in this chapter. Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Spark plug gap 0.052–0.056 inch (1.32–1.42 mm) 0.033–0.037 inch (.84– .94 ...

2. Long drivebelt is on second pulley groove farthest from engine. 3.5L V6 EcoBoost engine IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification Label be affixed to avehicle and prescr...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code 6F50 6–Speed Automatic Transmission J 6F55 6–Speed Automatic Transmission (withEcoBoost) G Maintenance and...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Remote start • Vehicle tracking and recovery* • Back up camera* • Protective seat covers* • Windshield wiper shaker* • Bumper and hitch mounted parking sensors* • Locking fuel plug for capless fuel systems *Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s ...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specifications and performance features. That’s why it’simportant to rely upon your dealership to properly diagnose and repairyour vehicle. Ford Motor Compa...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service? Factory-trained technicians Service technicians participate in extensive factory-sponsoredcertification training to help them become experts on the operati...

Multi-point inspection – Recommended each visit Accessory drive belt(s) Half-shaft dust boots (if equipped) Battery performance Horn operation Clutch operation (if equipped) Radiator, cooler, heater and A/C hoses Engine air filter Suspension components for leaks anddamage Exhaust system Steering and...

NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service interval. You shouldperform the engine oil change as indicated by the message center. Themessage center will display ENGINE OIL CHANGE SOON or OILCH...

Oil Change S ervice Interval* 1 23456789 1 0 1 1 1 2 1 3 1 4 1 5 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • •••••••••••••• Inspect wheels and related components for abnormal noise, wear , looseness or drag • •••••••••••••• Perform multi-po...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and filter as indicated by messagecenter and perform services listed in the NormalScheduled Maintenance chart (except Fiesta) Inspect f...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components forabnormal noise, wear, looseness or drag– Rotate tires,...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axlesare lubricated for life. These fluids are not...

ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km)(whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE...

A Accessory delay ........................102 Active Park Assist .....................276 AdvanceTrac ..............................258 Airbag supplemental restraintsystem ........................180, 189, 191 and child safety seats ............182description ..............180, 189, 191disposal .......

USB port ......................................39 V Vehicle Identification Number(VIN) ..........................................385 Vehicle loading ..........................237 Ventilating your vehicle ...........253 W Warning lights (see Lights) .......12Washer fluid ................................