Ford 2011 Fiesta v.2- Manuals

Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning andlubrication materials are significantsteps towards this aim. Information in this respect is highlighted in thisguide with the tree symbol. CALIFORN...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions couldresult in ...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”) only to help provide you with the directions, ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights can alert you to a vehicle condition that may becomeserious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make sure thebul...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Low fuel: Displays when the fuel level in the fuel tank is at or nearempty (refer to Fuel gaug...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by yourauthorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this light fails t...

AdvanceTrac 威 /Traction control (if equipped): Displays when the AdvanceTrac 威 /Traction control is active. If the light remains on, havethe system serviced immediately,refer to the Driving chapter for more information. Speed control (if equipped): Illuminates when the speed controlsystem is in use....

GAUGES Shown in standard measure. Metric similar. 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. Refer to Filling the tank in the Maintenance and Specifications chapter for more info...

mi (km) TRIP — Trip odometer: Registers the mileage of individual journeys. mi (km) TO E — Distance to empty: Indicates the approximate distance the vehicle will travel on the fuel remaining in the tank.Changes in driving pattern may cause the value to vary. AVG MPG (l/100km) — Average fuel consumpt...

the audio system. See Audio systems in the Entertainment Systems chapter for more information. • Set time: Move right to enter the menu and adjust the time. • Set date: Move right to enter the menu and adjust the date. • 24 hour mode: Move right to enter the menu to choose 24-hour mode. • Display: S...

Oil life monitoring system reset To reset the oil service light and clear the oil change message afterservicing use the following procedure: 1. Begin with the ignition off. 2. Turn the key to the accessory position for keyed vehicles and for pushbutton start vehicles press the Start/Stop button once...

AUDIO SYSTEMS AM/FM stereo or AM/FM stereo single CD/MP3 (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your ...

• Occupancy mode: Scroll to select Occupancy mode and move right or press OK to enter. Then, scroll to select from Optimize Allor Optimize Driver. Occupancy mode optimizes sound quality forthe chosen seating position. Press OK to confirm your selection. • DSP Equalizer: Scroll to select DSP Equalize...

• SYNC phone (if equipped): Scroll to select Phone Menu and then press OK to enter the menu. Refer to the SYNC 威 section in this chapter for more information. Note: SYNC Phone must be the selected feature to access this menu. • Audio: Scroll to select Audio and then move right to enter the menu. Scr...

The auxiliary input jack (AIJ)provides a way to connect yourportable music player to thein-vehicle audio system. This allowsthe audio from a portable musicplayer to be played through thevehicle speakers with high fidelity.To achieve optimal performance,please observe the followinginstructions when a...

WARNING: Store the portable music player in a secure location, such as the center console or the glove box, when the vehicle is in motion. Hard objects may become projectiles in a collision or suddenstop, which may increase the risk of serious injury. The audioextension cable must be long enough to ...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Privacy information When a cellular phone is connected to SYNC 威 , SYNC 威 creates a profile within your vehicle that is linked to that cellular phone. This profile iscreated in order to offer you more cellular features and to operate moreefficiently. Among other things, this profile may contain data...

• Caller ID Other features, such as text messaging via Bluetooth , and automatic phone book download are phone dependent features. To ensure that youhave a compatible cellular phone, refer to your phone’s user manual andvisit www.SyncMyRide.com or www.syncmaroute.ca. SYNC 姞 voice recognition feature...

Note: In the above possible commands, “< name >” is a dynamic listing in that it could be any desired name from your phone book. While in phone mode, you may also say “Menu” and then any ofthe following commands: • [Phone] settings [message] notification on • [Phone] settings [message] notific...

At any time, you may say these commands: • SYNC • USB • Line in • Bluetooth Audio • Phone • Voice settings • Cancel • Vehicle health report (if equipped, U.S. only) • Help • Services (if equipped, U.S. only) Voice commands when using Traffic, Directions & Informationservices (if equipped, U.S. o...

The first thing you must do to use the system is to ’pair’ your Bluetooth 威 enabled phone with your vehicle’s SYNC 威 system. This process allows your phone to wirelessly communicate with the hands-free SYNC 威 system and ensures that other phones cannot inadvertently do so. Topair your phone for the ...

Note: You can also manually enter the desired number by pressing the presets (0–9). Ending a call At any time, you can end an active phone call by pressing andholding or PHONE. Exiting phone mode When in phone mode but not in an active call, press and hold or PHONE to exit phone mode. Answering an i...

3. When the desired selection appears in the display, press OK. If you choose Reply to Text Message , SYNC 威 will take you back to the text messaging menu and allow you to again cycle through the list ofpredefined messages to send. If you choose Forward Text Message , SYNC 威 will take you to your ca...

Note: SYNC 威 supports a maximum of three callers on a multiparty/conference call. Accessing your call history and phone book during an active call Note: Accessing your phone book is a speed dependent feature. The vehicle must be moving less than 3 mph (5 km/h) to use this feature. You can access you...

Phone redial Phone redial will prompt your cellular phone with Bluetooth wireless technology to redial the last number called (if available). Note: To scroll, press / . 1. Press PHONE to enter Phone Menu . 2. When Phone Redial is selected, press OK. 3. When Redial? appears, press OK. Redialing ѧ wil...

Note: To scroll, press / . 1. Press PHONE to enter Phone Menu . 2. Scroll until Phonebook is selected and press OK. If there are fewer than 255 listings, SYNC 威 will list them alphabetically in flat file mode. If there are more than 255 entries listed, SYNC 威 will organize them into quick select alp...

Phone settings Note: These are phone dependent features. Under the phone settings menu on SYNC 威 , you can view the status of your paired phone with Bluetooth wireless technology, select from various ring tones, select message notification on/off, change phone bookentries and auto download your cell...

Note: If you choose to automatically download your cellular phone’s phone book every time your Bluetooth enabled phone reconnects to SYNC 威 , any changes, additions or deletions that have been saved since your last download will be deleted. Traffic, Directions and Information (if equipped, U.S. only...

Receiving Turn by Turn Directions To begin receiving directions: 1. Connect using either the voice commands or phone menu above. 2. When prompted, say, “Directions”. 3. Follow the voice prompts to identify your desired destination. 4. Once your destination is selected, a route is downloaded to your ...

911 Assist™ (if equipped) For 911 Assist™ to function properly, the vehicle must havebattery power after the crash, the cell phone must be previouslypaired, connected to SYNC 威 , and continue to function properly with the ability to make and maintain a 911 call initiated bySYNC 威 , and the 911 Assis...

2. Scroll until Vehicle Health is selected and press OK. 3. When User Preferences is selected, press OK. 4. When Automatic Reports is selected, press OK. 5. When the desired mile interval is selected (5000, 7500, or 10000),press OK. When the chosen mileage is reached, SYNC 威 will automatically promp...

1. Press PHONE to enter the Phone Menu . 2. Scroll until System Settings is selected and press OK. 3. Scroll until Advanced is selected and press OK. 4. Scroll until Master Reset is selected and press OK. 5. Press OK to confirm when prompted. The display will confirm whenthe reset is complete. SYNC ...

1. Plug the device into the vehicle’s USB port. 2. Press AUX repeatedly until SYNC 威 USB appears in the radio display. 3. Depending on how many digital media files are on your connecteddevice, Indexing may appear in the radio display until indexing is complete. You will then be taken to the Play Men...

1. Ensure that the desired music is playing on your paired phone andyour phone is in Bluetooth audio streaming mode. 2. Press AUX repeatedly until SYNC appears. 3. Press MENU. When Media Player Menu is selected, press OK. 4. Scroll until Select Source is selected and press OK. 5. Scroll until Blueto...

feature. The www.SyncMyRide.com website will walk you through theprocess of downloading the update to your USB and installing it in yourvehicle. Simply follow the directions on the website to download yourupdate. Once you have downloaded your AppLink™ update, Mobile Apps will appear as an option in ...

Note: To scroll, press / . 1. Press AUX repeatedly until SYNC appears. 2. Press MENU. When Media Player Menu is selected, press OK. 3. Scroll until System Settings is selected and press OK. 4. Scroll until Advanced is selected and press OK. 5. Scroll until Factory Defaults is selected and press OK. ...

• The MS SOFTWARE and/or FORD SOFTWARE may interface with and/or communicate with, or may be later upgraded to interface withand/or communicate with additional software and/or systems provided bythird party software and service suppliers. The additional software andservices of third party origin, as...

may use this information solely to improve their products or toprovide customized services or technologies to you. MS, MicrosoftCorporation, FORD MOTOR COMPANY, third party software andsystems suppliers, their affiliates and/or their designated agent maydisclose this information to others, but not i...

EXPORT RESTRICTIONS: You acknowledge that the SOFTWARE is subject to U.S. and European Union export jurisdiction. You agree tocomply with all applicable international and national laws that apply tothe SOFTWARE, including the U.S. Export Administration Regulations,as well as end-user, end-use and de...

Read and follow instructions Before using your Windows Automotive-based system, read and follow allinstructions and safety information provided in this end user manual(“User’s Guide”). Not following precautions found in this User’s Guidecan lead to an accident or other serious consequences. Keep Use...

MANUAL HEATING AND AIR CONDITIONING SYSTEM Manual system with A/C shown; heater only system similar. 1. : Turn to select the desired fan speed. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control setting: MAX A/C (if...

windshield. The system will automatically provide outside air to reducewindow fogging. To exit select another mode. 3. Temperature: Controls the temperature of the airflow in the vehicle. For optimum defrosting performance, set the dial to the hottest setting. 4. R : Press to activate/deactivate the...

For maximum cooling performance in MAX A/C mode: 1. Select MAX A/C. 2. Select the coolest temperature setting. 3. Set the fan to the highest speed initially. As the interior starts to cooldown, adjust the fan speed to maintain comfort. To aid in side window defogging/demisting in cold weather: 1. Se...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. High beams Pull the lever to the second detentto activate. Pull the lever again todeactivate. Flash-to-pass Pull the lever toward you slightly...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position and • the headlamp control is in the off or parking lamp position. WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. Th...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from thecenter...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. When changing lanes, the turn signal indicator can be programmed toflash either one or three times when the stalk is tapped. See Multifunction display in the Instrument cluster section for mo...

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product of this design. When moist airenters the lamp assembly through the vents, there is a possibility thatcondensation can occur when the temperature is...

Function Number of bulbs Trade number Headlamp (low beam) 1 H11B Headlamp (high beam) 1 HB3-9005LL Headlamp (park/turn) 1 3157NAK (amber) Headlamp (sidemarker) 1 168 4-door rear bodysidelamp(park/turn/sidemarker) 1 3157K 4-door rear deck lamp(backup) 1 921 5-door rear lamp(stop/reverse) 2 3157K 5-do...

Replacing the rear stop lamp (5-door) 1. Turn the bulb holdercounterclockwise and remove it. 2. Remove the bulb from the holder. 3. Reverse the procedure to install the new bulb. Replacing the reverse signal rear lamp (5-door) 1. Turn the bulb holdercounterclockwise and remove it. Lights 119 2011 Fi...

WINDSHIELD WIPERS Move the lever down for a singlewipe. For intermittent operation, move control up one position andadjust the rotary control to thedesired speed. For normal operation, move control up two positions and up three positions for high-speed wiping. Windshield washer To activate the winds...

To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12V DC/180W. If the power point or cigarlighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses....

4. Pull up the switch and hold until the window is fully closed. 5. Open the window and try to close it automatically. 6. Reset and repeat procedure if the window does not closeautomatically. Window lock The window lock feature allows onlythe driver and front passenger tooperate the power windows. T...

Note: A rear center passenger and/or raised rear center headrest (if equipped) may also block the light from reaching the sensor. Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products. EXTERIOR MIRRORS Power side view mirrors (if equippe...

Signal indicator mirrors (if equipped) When the turn signal is activated,the outer portion of the appropriatemirror housing will blink. This provides an additional warningto other drivers that your vehicle isabout to turn. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set sp...

Turning off speed control To turn off the speed control, press OFF or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) SYNC 姞 system hands free control feature Press (located on the ...

KEYS Integrated keyhead transmitters (IKTs) (If equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to yourvehic...

The IA key also contains aremovable mechanical key bladethat can be used to unlock thedriver door. To release themechanical key blade, press therelease buttons on the edge of thetransmitter and remove the keyblade. Your IA keys are programmed toyour vehicle. You cannot enter orstart your vehicle wit...

If both front doors are closed, the vehicle can be locked by any method,regardless of whether the key is in the ignition or not. Central locking/unlocking To centrally lock/unlock all doors (from the driver’s side only) using thekey from the outside when they are closed: • Turn the key counterclockw...

Autounlock (if equipped) If the doors have been autolocked, the doors will autounlock only when: • the ignition is turned off or to accessory, • the driver door is opened within 10 minutes of the ignition beingswitched from on to off or accessory. Note: If you use the power door lock button to lock ...

REMOTE ENTRY SYSTEM (IF EQUIPPED) FCC ID: LXP-RX4318 IC: 2298A-RX4318 The integrated keyhead transmitters (IKTs) and intelligent access keys(IA key) comply with part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not c...

The transmitter allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the trunk. • arm and disarm the perimeter anti-theft system. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition positionexcep...

Activating intelligent access atthe front doors: If your IA key is within 3 feet (1 meter) of thedriver’s door or passenger frontdoor, you can activate yourintelligent access system by pressingthe lock button. To lock the doors, press the lockbutton. To unlock the doors, press the lockbutton again. ...

2. Release the retaining clips with aflat object and separate the twohalves of the transmitter. 3. Carefully pry out the battery witha flat object. Be careful not to touchthe battery contacts or the printedcircuit board with the flat object. Note: Please refer to local regulations when disposing oft...

3. Twist a flat object in the positionshown to separate the two halves ofthe transmitter. 4. Carefully insert a flat object inthe position show to open thetransmitter. 5. Carefully pry out the batter with a flat object. Note: Please refer to local regulations when disposing of transmitter batteries....

Please read and understand the entire procedure before you begin. To reprogram the remote entry transmitters: 1. Insert the first programmed key into the ignition and turn the keyfrom off to run (maintain the key in run for approximately 3 seconds). 2. Turn the first key to off and remove it from th...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubles...

3. Lower the head restraint by pressing and holding the guide sleeveadjust release button (3) and pushing down on the head restraint (1). Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theback of your h...

To operate the heated seats: • Press the button located on theinstrument panel to activate. • Press again to deactivate. The heated seats will activate when the ignition is in the on position andthe engine is running. REAR SEATS Second row head restraints Your vehicle is equipped with rear seat outb...

SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash s...

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbaginflation energy. A lower, less forceful energy level is provided for morecommon, moderate-severity impacts. A higher energy level is used forthe most severe impact...

The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint us...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, frontpassenger sensing system, and the driver seat position sensor. Inaddition, the RCM also mon...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle. Restraint of pregnant women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. Theshou...

(8 km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers. In addition, the retractor is designed to lock if the webbing is pulled outtoo quickly. If this occurs, let the belt retract slightly and pull webbingout again in a slow and controll...

Safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,pull the button and slide the heightadjuster down. Releas...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximatelyone minute while the vehicle istraveling at least 6 mph(9.7 km/h) and more than1-2 minutes have elapsed sincethe ignition switch has beenturned to on... The Belt-Minder 威 feature is activated - the safety be...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• a readiness light and tone • and the electrical wiring which connects the components • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: Do not attempt to service, repair, or modify the side air curtain system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a side air curtain. See yourauthorized dealer. WARNING: All occupants of the vehicle, including the driver, should always wear their safe...

WARNING: If the side air curtain has deployed, the air curtain will not function again. The side air curtain system (including the A, B and C pillar trim and headliner) must beinspected and serviced by an authorized dealer. If the air curtain is not replaced, the unrepaired area will increase the ri...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier,convertible seat,or toddler seat). Smallc...

• When possible, always properly restrain children twelve (12) years ofage and under in a rear seating position of your vehicle. Accidentstatistics suggest that children are safer when properly restrained inthe rear seating positions than in a front seating position. Recommendations for attaching ch...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced390 mm (15 inches) apart. The standardized spacing for LATCH loweranchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH at...

2. Locate the correct anchor for theselected seating position. 3. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 4. Tighten the child safety seat tether strap according to themanufa...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a p...

Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance Guide chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. • Front-wheel drive (FWD) vehicles(front tires at top of diagram) Sometimes irregular...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label, which is located on the B-Pillar or the edge of thedriver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction and Tempe...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Low tire pressurewarning light Possible cause Customer action required Solid warning light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low tire pressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

under-inflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflation pressure. SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of a...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum...

numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR. GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle Weight Rating) – is the max...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

Before you tow your vehicle, follow these directions for your specificvehicle configuration: Vehicles with a manual transmission: 1. Release the parking brake. 2. Move the gearshift to the neutral position. 3. The maximum towing speed is 70 mph (113 km/h). 4. There is no limitation on towing distanc...

STARTING Positions of the ignition If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. 0 (off) — locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. This position also shuts theengine ...

Starting the engine Note: If your vehicle is equipped with a push button start system, refer to Push button start system in this section for starting. 1. Turn the key to II (on) withoutturning the key to III (start). 2. Turn the key to III (start), thenrelease the key as soon as theengine begins cra...

Ignition modes 1. Off — press and release the START/STOP button without applying thebrake pedal (automatic transmission) or clutch pedal (manualtransmission) when your vehicle is in on mode or when the engine isrunning. Note: In order to switch off the engine while the vehicle is in motion, shift to...

Backup method of starting: Your IA key uses a radio frequency signalto communicate with your vehicleand authorize your vehicle to startwhen you press the START/STOPbutton and apply the brake pedal orclutch pedal. If excessive radiofrequency interference is present inthe area, or if the battery in yo...

vehicle may have taken the IA key when exiting the vehicle. If the IA keyis no longer present in the vehicle, you will not be able to re-start yourvehicle outside of the Fast Restart time (see Fast Restart Feature above). It is important to be aware of where your IA key is located in thevehicle, to ...

outdoors, in cold temperatures, and is clearly marked “Suitable for Usewith Outdoor Appliances.” Never use an indoor extension cordoutdoors; it could result in an electric shock or fire hazard. • Use a 16-gauge outdoor extension cord, minimum. • Use as short an extension cord as possible. • Do not u...

Make sure system is unplugged and properly stowed before driving thevehicle. While not in use, make sure the protective cover seals theprongs of the engine block heater cord plug. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, ...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. (I...

If the TCS is activated excessively in a short period of time, the brakingportion of the system may become temporarily disabled to allow thebrakes to cool down. In this situation, TCS will use only engine powerreduction or transfer to help control the wheels from over-spinning.When the brakes have c...

The EPS system has diagnostic checks that continuously monitor theEPS system to ensure proper operation. When a system error isdetected, the following message STEERING MALFUNCTION SERVICENOW, STEERING MALFUNCTION STOP SAFELY, POWER STEERINGMALFUNCTION SERVICE NOW may display in the multifunction dis...

WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Understanding the gearshift positions of the 6–speed automatictransmission (if equipped)...

• Allows the transmission to select gears that will provide the desiredengine braking based on the vehicle inputs mentioned above. This willincrease engine RPM during engine braking. Overdrive cancel with grade assist is designed to provide optimal gearselection in hilly terrain or mountainous areas...

Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to thetransmission and tires may occur, or the engine may overheat. MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clut...

Upshift according to the following chart: Recommended upshifts (for best fuel economy) when accelerating 5-speed manual transmission Shift from: 1 - 2 14 mph (23 km/h) 2 - 3 24 mph (39 km/h) 3 - 4 32 mph (51 km/h) 4 - 5 44 mph (71 km/h) Reverse Make sure that your vehicle is at a complete stop befor...

BLIND SPOT MIRRORS Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer to Exterior mi...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

Owner Guide portfolio in the glove compartment. In Canada, the card isfound in the Warranty Guide in the glove compartment. U.S. Ford, Mercury and Lincoln vehicle customers who require RoadsideAssistance, call 1-800-241-3673. Canadian customers who require roadside assistance, call1-800-665-2006. If...

In some instances the vehicle may not restart the first time you try torestart and may take one additional attempt. WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected circuits F1 15A Ignition switch, Keyless entryignition relay, Keyless entryaccessory relay F2 10A Electronic mirror, A/C clutch,Engine compartment fuse panel F3 7.5A Instrument cluster F4 7.5A Passenger airbag deactivation...

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. To remove a fuse, use the fuse puller tool provided on the inside of thepassenger compartment fuse panel cover. The high-current fuses are coded as follows: Fuse/Relay Lo...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

9. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. 10. Put the flat tire, jack and lugwrench away. Make sure the jack isfastened so it does not rattle whenyou drive. Unbloc...

Note: Inspect the wheel pilot hole prior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot sur...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+) terminal of the assisting battery. 3. Connect the negative (-) cable tothe negative (-) terminal of theassisting battery. 4. Make the fi...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remover (ZC-42). WINDOWS ...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth, then use a clean and dry white cottoncloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instr...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleather conditioners. These products may cause premature wearing ordamage to the leather. LEATHER SEATS FOR THE KING RANCH 姞 EDITION ONLY (IF EQUIPPED) Your...

• Clean the surfaces using the steps outlined in the Cleaning section. • Ensure the leather is dry then apply a nickel-sized amount ofconditioner to a clean, dry cloth. • Rub the conditioner into leather until it disappears. Allow theconditioner to dry and repeat the process for the entire interior....

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel. 2. Raise the hoo...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Engine oil filler cap 3. Battery 4. Brake/Clutch fluid reservoir 5. Power distribution box 6. Windshield washer fluid reservoir 7. Air filter assembly 8. Engine oil dipstick 8 7 6 5 1 2 3 4 Maintenance and Specifications...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

To replace the wiper blades: 1. Pull the wiper arm away from thewindshield. 2. Press the locking button (1). 3. Remove the wiper blade (2). Note: Make sure the wiper blade locks into place. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate interval...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford pro...

WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near thebattery, always shield your face and protect your eyes. Always provideproper ventilation. WARNING: When lif...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. When the battery is disconnected or a new battery installed, theautomatic transmission must relearn its adaptive strategy. As a result ofth...

• Proper function of calibrated gauges. When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine coolantreservoir (depending upon application). • Refer to sc...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. DO NOT MIX recycled coolant and new (unused) coolant together in the vehicle. Mixing of enginecoolants may harm your engine’s cooling system. The use of animproper coolant may harm engine and co...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reservoir.If you removed the radiator cap in an ...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling ...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87.Some stations offer fuels posted as“Regular” with an octane ratingbelow 87, particularly in high altitude areas. Fuels with octane levelsbelow 87 are not recommended. Do not be co...

• Use a known quality gasoline, preferably a national brand. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in ...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

BRAKE/CLUTCH FLUID Brake and clutch (if equipped) systems are supplied from the samereservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toad...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis 5-10 mm below the bottom of theope...

6. Replace the air filter housing cover and install the screws. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage tothe engine if the correct air filter element is not used. VEHICLE STORAGE If you plan on storing ...

Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up onwindow surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collecte...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Keyless entry keypad • Seat covers* • Remote start • Windshield wiper shaker* • Wheel locks • Vehicle tracking and recovery* • Back-up camera* • Bumper mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s warranty. Ford Licensed Acces...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty cove...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft 威 or Ford-authorized remanufactured parts that are used for maintenance replacement or for the service ofcomponents affecting emission control must be equivalent to genuineFord Motor Company parts in...

Genuine Ford and Motorcraft 姞 replacement parts Ford and Lincoln Mercury dealerships stock Ford and Motorcraft 威 branded replacement parts. These parts meet or exceed Ford MotorCompany’s specifications, and we stand behind them. Parts installed atyour Ford or Lincoln Mercury dealership carry a natio...

Multi-point inspection In order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help identifypotential issues and prevent major problems. Ford Motor Companyrecommends the following multi-point inspection be performed at everyschedule...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) intervals with exceptionsnoted. Reset your oil life monitoring system after each engine oil andfilter change; refer to the Instrument Cluster chapter. ...

Miles (x 1,000) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Kilometers (x 1,000) 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 Months 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180 Change engine oil and filter • • ••••••••••••• Rotate tires, inspect tire wear and measure tread de...

Every 20,000 miles(32,000 km) Replace cabin air filter (if equipped) Every 30,000 miles(48,000 km) Replace climate-controlled seat filter (ifequipped) Replace engine air filter Every 100,000 miles(160,000 km) Change engine coolant 1 Replace spark plugs Inspect accessory drive belt(s) 2 Every 150,000...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below, you will need to have some items maintained more frequently. If you only occasionally operate your vehicle under these conditions, it is not...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components forabnormal noise, wear, looseness or drag– Rotate tires,...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-designaxles are lubricated for life. These lubricants...

COOLANT CHANGE RECORD Engine coolant ❑ Initial change – 6 years or 100,000 miles (160,000 km) (whichever comes first). ❑ After initial change - every 3 years or 50,000 miles (80,000 km). Scheduled Maintenance Guide 350 2011 Fiesta (fie) Owners Guide, 2nd PrintingUSA (fus)

Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M...

911 Assist™ ................................66 A Accessing and using your USBport ..............................................81 Accessing call history/phonebook during active call ...............55 Accessing system settings .........84 Accessing vehicle applications ..83 Accessing your phone book...