Ford 2011 F-550 v.1- Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

Notice to owners of pickup trucks and utility type vehicles WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully.Your vehicle is not a passenger car. As with other vehicles of this ty...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

Vehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’s Warranty Guide for more information. Some vehicles are equipped wit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster with standard measure shown; metricsimilar Optional instrument cluster with standard measure shown; metricsimilar Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light...

bulb works. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information. Standard message center Note: Some warning lights are reconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These lightsfunction t...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Check fuel cap: Displays when the fuel cap may not be properlyinstalled. Continued driving wit...

WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle.Have the vehicle checked by your authorized dealer. Driving extendeddistances with the parking brake engaged can cause ...

AdvanceTrac 威 /Traction control (if equipped): Displays when the AdvanceTrac 威 /Traction control is active. If the light remains on, havethe system serviced immediately,refer to the Driving chapter for more information. AdvanceTrac 威 /Traction control off light (if equipped): Illuminates when Advanc...

Speed control (if equipped): The speed control system indicator lightchanges color to indicate what modethe system is in: • On (amber light): Illuminates when the speed control system is turned on. Turns off when the speedcontrol system is engaged or turned off. • Engaged (green light): Illuminates ...

GAUGES Base cluster with automatic transmission shown. Metric similar. 1. Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H). Ifthe needle falls below the normal range, stop the vehicle, turn off theengine and check the en...

Altering the severity of the driving conditions is recommended to lowerthe transmission temperature into the normal range. Red area The transmission fluid is overheating. Stop the vehicle to allow the temperature to return to normal range. If the gauge is operating in the yellow or red area, stop th...

Selectable features Info (information menu) Press the INFO button repeatedly tocycle through the following features: TRIP A/B Registers the distance of individual journeys. Press and release the INFObutton until the TRIP A/B appear in the display (this represents the tripmode). Press and hold the RE...

XX.X AVG MPG (L/100km) Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km. If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed...

System check and vehicle feature customization Press the SETUP button repeatedlyto cycle the message center throughthe following features: Note: When returning to the SETUP menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed tochange back to English. Press and...

ZONE <XX> RESET = CHANGE The compass heading is displayed as one of N, NE, E, SE, S, SW, W andNW in the message center display. Refer to Compass zone/calibration adjustment. RESET FOR CALIBRATION This feature calibrates the compass. The compass reading may be affected when you drive near large...

Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessories (heater/air conditioning, wipers, etc.) and make sure allvehicle doors are shut. 7. Press the RESET button until the display reads RESET FORCALIBR...

LANGUAGE = ENGLISH / SPANISH / FRENCH Allows you to choose which language the message center will display in.Selectable languages are English, Spanish, or French. Waiting four seconds or pressing the RESET button cycles the messagecenter through each of the language choices. Press and hold the RESET...

TO EXIT 4X4 LOW APPLY BRAKE (if equipped) — Displayed when 2WD is selected from 4X4 LOW mode. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. SHIFT DELAYED PULL FORWARD (if equipped) — May display when shifting to or from 4X4 LOW. For more information, refer t...

SPEED LIMITED YYKMH IN XXXKM EXHAUST FLUID EMPTY(Diesel engine only) — Displayed when the diesel exhaust fluid is nearing empty. The vehicle’s top speed will become limited in thedisplayed distance. The diesel exhaust fluid must be replenished toresume normal operation of the vehicle. Refer to your ...

ENGINE IDLED SEE MANUAL CONTAMINATED EXHAUSTFLUID (Diesel engine only) — Displayed when the diesel exhaust fluid is contaminated. The vehicle will enter into an idle-only mode. Thediesel exhaust fluid must be replaced to resume normal operation of thevehicle. Refer to your diesel supplement for more...

Main menu From the main menu screen you can choose the following: • Gauge Mode • Trip A/B • Fuel Economy • Truck Apps (if equipped) • Settings • Information Scroll up/down to highlight one of the options, then press the right arrowkey or OK to enter into that menu option. Gauge Mode Gauge Detail: In...

• 10 Minutes. • 30 Minutes. • Last 5 Resets. Use the up/down arrows keys to highlight one of the choices; press andhold OK to set your choice. The graph is updated each minute with the fuel economy that wasachieved during the prior 5, 10, 30 minutes or last 5 resets of driving. Truck Apps (if equipp...

When “Press OK for options” is displayed, pressing OK will open thetrailer options menus: Trailer Change ActiveTrailer When this is highlighted, press the right arrow keyto change the currently selected trailer. Use the upand down arrows to select a trailer and press theOK button to choose the highl...

Trailer Rename Trailer Press the right arrow button when this is highlightedto display saved or default trailers. Use the up/downbuttons to highlight a trailer and press OK to selectit. Use the up/down arrow buttons to change thecharacters as needed. When done, press OK toaccept the change. Reset Tr...

MyKey Create MyKey Press and hold OK to create MyKey AdvanceTrac Always on or Selectable MAX MPH(km/h) 80 MPH (120 km/h) or Off Speed Warning 45, 55 or 65 MPH (75, 90 or 105 km/h) Volume Limiter On/Off Clear MyKeys Hold OK to Clear MyKeys Language English, Español, Français Units Distance Miles and ...

System Check Brakes Tire Pressure Trailer BrakeCtrl. Gain and Output (when trailer is connected) No trailer (when no trailer is connected) Trailer Sway Park Aid Check Rear Park Aid Fuel Level (distance to empty) Some items will only display during a system check if a problem hasbeen detected. If an ...

POWER REDUCED TO LOWER ENGINE TEMP — Displayed when the engine temperature gauge needle moves to H. You may noticereduced engine power. Refer to Engine coolant in the Maintenance and Specifications chapter for more information. CLEANING EXHAUST FILTER (diesel engine only) — Displayed when the vehicl...

can be properly circulated to avoid engine damage from lack oflubrication. A timer will begin a countdown from 30 seconds. Once thecounter has reached 0 seconds, OK TO DRIVE will be displayed and theengine will respond to accelerator pedal movement. Refer to your dieselsupplement for more informatio...

SPEED LIMITED TO XX MPH UPON RESTART CONTAMINATEDEXHAUST FLUID (diesel engine only) — Displayed when the diesel exhaust fluid is contaminated. Speed will be limited upon restart. Thediesel exhaust fluid must be replaced to resume normal operation of thevehicle. Refer to your diesel supplement for mo...

TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when 2WD is selected while the vehicle has been stopped in 4X4 LOW. Formore information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TO EXIT 4X4 LOW SLOW TO 3 MPH (if equipped) — Displayed when 2WD is selected while the vehic...

AUDIO SYSTEMS AM/FM stereo system (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility ...

current track is finished playing. CD SHUF will appear in the display. Todisengage, press SHUFFLE again. SHUFFLE OFF will appear in thedisplay. Note: In CD/MP3 mode, press SHUFFLE to play the tracks in random order. In MP3 folder mode, the system will randomly play all trackswithin the current folde...

In satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE,press again to scroll through the current song title, artist, channelcategory and the SIRIUS 威 long channel name. In TEXT MODE sometimes the display requires additional ...

Auxiliary input jack (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeop...

USB port (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of t...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location th...

SINGLE ZONE CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fogand thin ice. The system will automatically provide outside air to reducewindow fogging. Press this button again to return to the prev...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Optional or Standard message center in the Instrument Cluster chapter. 1. – / + Fan speed control: Press to decrease/increase the fan speed. 2. A. R Rear defroster (if equ...

• : Distributes air through the instrument panel vents, floor vents, rear seat floor vents and de-mister vents. • : Distributes air through the floor vents and rear seat floor vents. 5. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and e...

13. DUAL: Press to engage/disengage separate passenger side temperature control. 14. Power: Press to activate/deactivate the climate control system. When the system is off, outside air is prevented from entering the vehicle. 15. Driver cooled seat (if equipped): Press to control the driver cooled se...

For maximum cooling performance: • Automatic operation: 1. Press AUTO for full automatic operation. 2. Do not override A/C or (recirculated air). 3. Set the temperature to 60°F (16°C). • Manual operation: 1. Select MAX A/C. 2. Select (recirculated air). Use (recirculated air) with A/C to provide col...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position to turn on the parking lamps. Rotate clockwise to the secondposition to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights no...

3. Turn the ignition switch to on and then back to off. 4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. Fog lamp control (if equipped) The headlamp cont...

Vertical aim adjustment The headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments. To adjust the headlamps: 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet ...

TURN SIGNAL CONTROL The turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activation andcancellation is electronic. • To operate the left turn signal,push the lever down until it stopsand release. • To operate the right turn signal...

To turn on the map lamps, press thelamp. The dome lamp turns on when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesylamps come on, and • any of the remote entry controls are pressed and the ignition is off. BULB REPLACEMENT Lamp assembly condensation Exte...

Replacing exterior bulbs Check the operation of all the bulbs frequently. Function Number of bulbs Trade number Headlamps 2 H13/9008 Park/Turn lamp 2 3157NA Sidemarker 2 W5W Tail/stop/turn/sidemarker (pick-up only) 2 3157 Tail/stop/turn/sidemarker (chassis cabsonly; if equipped) 2 3157 Back-up (pick...

2. Using masking tape or a marker,make an alignment mark betweenone of the grille brackets and thevehicle radiator support to ensurecorrect grille alignment duringre-assembly. Do not scratch theblack coating from the radiatorsupport. 3. Remove the two grille toheadlamp assembly push pins andthe four...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down and in or out until youfind the desired position. 3. While holding the steering wheelin place, pull the lever ...

One-touch down Allows the driver’s window to open fully without holding the controldown. Press the switch completely down to the second detent andrelease quickly. The window will open fully. Momentarily press the switchto any position to stop the window operation. Window lock (if equipped) The windo...

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equi...

3. Return to the center position to lock mirrors in place. The spotter mirror below the main glass (if equipped) must be adjustedmanually. Heated outside mirrors (if equipped) The main mirror glass and lowerconvex spotter mirror are heated toremove ice, mist and fog. To activatethe heated mirrors, p...

Mirror-mounted side turn signal indicator (if equipped) When the vehicle turn signals areactivated, the outer portion of themirror housing will blink amber. The turn signal feature can be seenby other drivers who may approachfrom the rear of the vehicle. Clearance lamps (if equipped) Illuminates whe...

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected. Refer to Memory seats/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter. SPEED CONTROL (IF...

Press to scroll through various menus and selections. Press OK to confirm your selection. For further information on the SYNC 威 system, refer to the SYNC 威 supplement. Navigation system/SYNC 威 hands free control features (ifequipped) Press VOICE briefly until thevoice icon appears on the navigation ...

If your vehicle is equipped with this option, there will also be a relay boxlocated on the driver side end of the instrument panel. See yourauthorized dealer for service. The relays are coded as shown inthe accompanying illustration. There will also be one power leadfor each switch found as a blunt-...

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) Your vehicle may be equipped with a universal garage door opener whichcan be used to replace the common hand-held transmitter. Car2U 姞 Home Automation System (if equipped) The Car2U 威 Home Automation System is a universal transmitterlocated in the driver’s ...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. Tailgate removal Your tailgate is removable to allow more room for loading....

2. Open the latches to release thepanels. 3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels. Driver Controls 124 2011 F-250/350/450/550 (f23) Owners Guide, 1...

KEYS Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-p...

MyKey™ restricted features Standard settings – These settings cannot be changed • The audio system will be muted whenever Belt-Minder 威 is activated until the safety belts are buckled. Refer to the Seating and Safety Restraints chapter for a detailed description of Belt-Minder 威 operation. • Low fue...

For optional message center 1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key. 2. Press OK to select CREATE MYKEY. 3. Hold OK as prompted until you see MARK THIS KEY AS RESTRICTED. MyKey™ is successfully programmed. Make sure you label it so you candistinguish...

2. Use the up and down arrows to get to any of the optional features. 3. Press the right arrow key to bring up the settings available for eachfeature. 4. Press OK or the right arrow key to make your choice. Disable MyKey™ To reset all MyKeys™ as admin keys do the following: For standard message cent...

Using MyKey™ with remote start systems MyKey™ is not compatible with non Ford-approved aftermarket remotestart systems. If you choose to install a remote start system please seeyour authorized dealer for a Ford approved remote start system. The following information MAY help customers who choose to ...

Note: For all vehicles with a non Ford-approved remote start installed, it is possible to program all ’real’ keys as MyKeys™, in which case, you willneed to use your remote start system to reset all MyKeys™ as adminkeys by doing the following: 1. Enter the vehicle, close all doors. 2. Remote start t...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a ...

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The IKT allows you to: • remotely unlock the ...

Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and one step door unlocking by pressing andholding both the and buttons simultaneously on the remote entry transmitter for approximately four seconds. The ...

2. Press and hold control button 1for five seconds. A tone will beheard after two seconds confirmingmemory position has been set.Continue to hold until a second toneis heard after five seconds. 3. Within three seconds pressthe . 4. A tone will be heard when thetransmitter programming iscomplete. 5. ...

3. Insert the new battery. Refer tothe instructions inside the IKT forthe correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery housing cavity. 4. Snap the battery cover back ontothe key. Note: Replacement of the battery will not cause the ...

Starting the engine with remote start To start the engine using remote start: Note: Each button press must be done within 3 seconds of each other. If this sequence is not followed the vehicle will not remote start and thehorn will not chirp. 1. Press on the IKT to lock all the doors. 2. Press two ti...

3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. Your personal code is now erased and only the factory set 5–digit codewill work. Anti-scan feature If an incorrect code has been entered seven times (35 consecutivebutton presses), the keypad wil...

Arming the system When armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash thepark/turn lamps and will sound the horn. The system is ready to arm whenever the key is removed from theignition. Either of the following actions will pr...

FRONT SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Befo...

To reinstall the non-adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. WARNING: The non-adjustable head restraint is a safety device. It should be installed whenever the seat is occupied. WARNING: To mini...

• Pull the release lever handlelocated on the side of the seat upto move the seatback forward orbackward. 20 percent front seat armrest and console (if equipped) To release the armrest and gainaccess to the cupholders andseatback storage bin, press thebutton on the right-hand side of theseat and pul...

To gain access to the under-seatstorage compartment (if equipped)in your seat cushion, lift the latch toopen the lid. The lid cannot beopened when the armrest is down. The under-seat storagecompartment (if equipped) has aprogrammable lock. Use the ignitionkey to program the lock to thecompartment. E...

Heated and cooled seats (if equipped) The controls for the climate controlled seats are located on the dualelectronic automatic temperature control (DEATC) system. Heated seats WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord in...

4. Cycle the ignition key between the off position and the on position atotal of three times ending with the ignition in the off position. 5. Engage the forward or rearward seat switch. 6. Remove the ignition key from the ignition switch. (The driver seatmay move rearward if the easy entry/exit feat...

Rear center armrest (if equipped) To use the armrest simply rotate itforward from the seatback. Rear under seat storage (if equipped) (Crew Cab) The rear seat has storage space located under the seat cushion. Lift up the lever and flip up the seatcushion to access the storage spaceand the power poin...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use th...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. Restraint of pregnant women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shou...

Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This mode should be used any time a ch...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. WARNING: After any vehicle collision, the front passenger and rear outboard s...

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned t...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the onposition... The Belt-Minder 威 feature will not activate. The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are...

Reasons given... Consider... “The people I’m with don’t wearbelts” Set the example, teen deaths occur 4times more often in vehicles with TWOor MORE people. Children and youngerbrothers/sisters imitate behavior theysee. “I have an airbag” Airbags offer greater protection whenused with safety belts. F...

WARNING: While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belted and surviving an accident. We recommend youleave the Belt-Minder 威 system activated for yourself and others who may use the vehicle. To reduce the risk of in...

WARNING: Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly...

WARNING: An infant in a rear-facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unlessthe passenger airbag is turned off. See Passenger airbag ON/OFF switch. WARNING: Front seating position...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy 威 System is provided. WARNING: To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy 威 . How does the...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Warning lights and chimes in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the syst...

3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger airbag to pose a special risk for the passenger;and • makes the potential harm from the passenger airbag in a crash greaterthan the potential harm from turning OFF the airbag an...

3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the airbag deploys; and • makes the potential harm from the passenger airbag deploymentgreater than the potential harm from turning OFF the airbag andexperie...

WARNING: All children are shaped differently. The Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safetyorganizations or are the minimum requirements of law. Ford recommendschecking with a NHTSA Certified Child Passenger Safety...

• You are required by law to properly use safety seats for infants andtoddlers in the U.S. and Canada. • Many states and provinces require that small children use approvedbooster seats until they reach age eight, a height of 4 ft 9 in(1.45 meters) tall, or 80 lb (36 kg). Check your local and state o...

WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collision. WARNING: Do not leave children, unreliable adults, or pets unattended...

SAFETY SEATS FOR CHILDREN Infant and/or toddler seats Use a safety seat that is recommended for the size and weight of thechild. When installing a child safety seat: • Review and follow the informationpresented in the Airbag supplemental restraint system(SRS) section in this chapter. • Carefully fol...

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent accidental unbuckling. • Place vehicle seat back in upright position. • This vehicle does not require the use of a locking clip. WARNING: Depending on w...

7. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should be nomore than one inch (2.5 cm) ofmovement for proper installation....

Tether strap attachment 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, other wise routethe tether strap over the top of the seatback. If the top ...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thiscondition. Do not introduce any item thicker than this under the boosterseat. Check with the booster seat manufacturer’s instructions. The importance of shoul...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The ...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

under-inflation of the tires, improper tires (load range, size, or type), orvehicle modifications such as lift-kits. In the event that your vehicleexperiences shimmy, you should slowly reduce speed by either lifting offthe accelerator pedal or lightly applying the brakes. The shimmy willcease as the...

Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type/mini-spare tires (see the Dissimilar spare tire/wheel information section for description): Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires (see the Dissimilar spare tire/...

WARNING: Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that may be wedged in thetread grooves. Check the tire an...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance Guide chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. • Rear-wheel drive (RWD)vehicles/Four-wheel drive(4WD)/All-wheel drive (AWD)vehicles ...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The ...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low tire pressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a description ofhow the system functions underthese condi...

TPMS reset procedure The TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressures in the front tires as compared to the rear tires. WARNING: To determine the required pressure(s) for your vehicle – refer to the Safety Compliance ...

8. Remove the valve cap from the valve stem on the right rear tire.Decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire.Decrease the air pressure until the horn sounds. Training is complete after the horn sounds for the last tire trained(...

Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines. • Drive cautiously. If you hear the chains rub or bang against yourvehicle, stop and re-tighten the chains....

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

TRAILER TOWING Note: The trailer towing chart in this section applies to vehicles equipped with a gasoline engine; for vehicles equipped with a dieselengine, refer to your diesel supplement. Your vehicle may tow a Conventional/Class IV trailer or fifth-wheel trailerprovided the maximum trailer weigh...

Fifth-wheel trailer hitch (if equipped) To find the maximum trailer weight allowed for your vehicle, consultyour authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer). Fifth-wheel and gooseneck towing Your vehicle may be equipped with a fifth-wheel prep package. T...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. WARNING: If you own a trailer with a hydraulic brake system, do not connect the...

The TBC user interface consists ofthe following: 1. +/- (GAIN adjustment buttons): Pressing these buttons will adjust the TBC’s power outputto the trailer brakes (in0.5 increments). The GAIN settingcan be increased to a maximum of10.0 or decreased to a minimum of 0 (no trailer braking). Pressing and...

2. Manual control lever: Slide the control lever to the left to activate power to the trailer’s electric brakes independent of the tow vehicle’sbrakes (see the following Procedure for adjusting GAIN section for instructions on proper use of this feature). If the manual control isactivated while the ...

6. If the trailer wheels lock-up (indicated by squealing tires), reduce theGAIN setting; if the trailer wheels turn freely, increase the GAIN setting.Repeat Steps 5 and 6 until the GAIN setting is at a point just belowtrailer wheel lock-up. If towing a heavier trailer, trailer wheel lockup maynot be...

• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lockup.Therefore, if these systems are not functioning properly the TBC maynot function at full performance. • When the vehicle is turned off, the TBC Output is disabled and the...

Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to Special operating conditions in the Scheduled Maintenance Guide chapter. Trailer towing safety tips General • Ensure that the trailer, safety chains and 7–pin electrical...

Braking • Anticipate the need to stop; allow much more distance and time tostop than normal. • Do not apply the trailer brakes for extended periods of time as theycan overheat and lose effectiveness. • The trailer brakes must be inspected and serviced at intervalsspecified by the manufacturer. This ...

RECREATIONAL TOWING Follow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehicle behinda motorhome. These guidelines are designed to ensure that yourtransmission is not damaged. Note: Put your climate control system in recircu...

STARTING Positions of the ignition 1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3. On— all elect...

WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. WARNING: If you smell exhaust fumes inside your vehicle, ha...

Cold weather starting (flexible fuel vehicles only) The starting characteristics of all grades of E 85 ethanol make it unsuitable for use when ambient temperatures fall below 0°F (-18°C).Consult your fuel distributor for the availability of winter grade ethanol.As the outside temperature approaches ...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5 cm) or adjust the heating orair conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant...

• Make certain that the extension cord is in excellent condition (notpatched or spliced). Store your extension cord indoors attemperatures above 32°F (0°C). Outdoor conditions can deteriorateextension cords over a period of time. • To reduce the risk of electrical shock, do not use your heater withu...

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be inspected by an authorized dealer. If the vehicle hascontinuous vibration or shudder in the steering wheel while braking, thevehicle ...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

Pull the release lever to release theparking brake. To prevent the pedalfrom releasing too quickly, placeyour left foot on the service brakepedal, then slowly pull the releaselever until the pedal slowly releases.Make sure that the pedal is fullyreleased. You may want to pull therelease lever again ...

Roll Stability Control™ (RSC 威 ) Roll Stability Control™ (RSC 威 ) may help to maintain roll stability of the vehicle during adverse maneuvers. RSC 威 operates by detecting the vehicle’s roll motion and the rate at which it changes and by applying thebrakes to one or more wheels individually. During a...

HILL DESCENT CONTROL (IF EQUIPPED) Hill descent control allows the driver to set and maintain vehicle speedwhile descending steep grades in various surface conditions. WARNING: Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep gra...

Note: Noise from the ABS pump motor may be observed during hill descent control operation. This is a normal characteristic of the ABS andshould be no reason for concern. Hill descent modes • At speeds below 20 mph (32 km/h): When the HDC switch is pressedand HDC is active, the HDC telltale will flas...

• loose or worn steering components • improper steering alignment If any steering components are serviced or replaced, install newfasteners (many are coated with thread adhesive or have prevailingtorque features which may not be re-used). Never re-use a bolt or nut.Torque fasteners to specifications...

For 2WD vehicles and vehiclesequipped with a manual shift4WD system: Turn the control to ON. Theindicator light will display in theinstrument cluster. Once the light is displayed in the instrument cluster, both rear wheel axle shafts will be locked together providing added traction. If the indicator...

WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slungsports cars are designed to per...

AUTOMATIC TRANSMISSION OPERATION Understanding the shift positions of the 5–speed automatictransmission (if equipped) This vehicle is equipped with an adaptive transmission shift strategy.Adaptive transmission shift strategy offers the optimal transmissionoperation and shift quality. When the vehicl...

3 (Third) Transmission starts and operates in third gear only. Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additionalengine braking on downgrades. 1 (First) • Provides maximum engine b...

By moving the gearshift lever from the D (Drive) position to the M(Manual) position you may now manually select the gear you desire.Only the current gear will be displayed. Press the + button or the –button to upshift or downshift. If the – button is pressed at a vehiclespeed that would cause an eng...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system,located on the tailgate, provides avideo image, which appears in therearview mirror or on the navigationscreen (if equipped), of the areabehind the vehicle. It addsassistance to the driver whilereversing or reverse parking thevehicle. T...

Night time and dark area use At night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is necessary that bothreverse lamps are operating in order to get a clear image in the dark. Ifeither of the lamps are not operating, stop using the cam...

4WD system indicator lights The indicator lights illuminate in the message center in thereconfigurable telltale (RTT) under the following conditions. Refer to Warning lights and chimes in the Instrument Cluster chapter. • 4X2 - Momentarily illuminates when 2H is selected on electronicshift 4WD syste...

3. Move the transfer case shift leverthrough N (Neutral) directly to 4L(4x4 Low). 4. If the shift lever does not, or onlypartially moves to the 4L (4x4 Low)position, perform a shift with thetransmission in N (Neutral) and thevehicle rolling at a speed below3 mph (5 km/h). This will ensure the transf...

Shifting to/from 4L (4X4 low) 1. Bring the vehicle to a speed of 3 mph (5 km/h) or less. 2. Place the transmission in N (Neutral). 3. Move the 4WD control to the desired position. The message center will display 4X4 SHIFT IN PROGRESS during the shift. The message center will then display the system ...

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps. You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and braking control of your vehicle, you must have all fourwheels ...

Sand When driving over sand, try to keep all four wheels on the most solidarea of the trail. Avoid reducing the tire pressures but shift to a lowergear and drive steadily through the terrain. Apply the accelerator slowlyand avoid spinning the wheels. Avoid excessive speed because vehicle momentum ca...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford MotorCompany joins the U.S. Forest Service and the Bureau of LandManagement in encouraging you to help preserve our national forest andother ...

WARNING: If you are driving in slippery conditions that require tire cables, then it is critical that you drive cautiously. Keep speeds down, allow for longer stopping distances and avoid aggressivesteering to reduce the chances of a loss of vehicle control which canlead to serious injury or death. ...

Ford Super Duty Vehicles are qualified for use as a stationary or mobilepower source, within limits detailed in the Ford Truck Body Builders Layout Book, found at www.fleet.ford.com/truckbbas, and through the Ford Truck Body Builders Advisory Service. For stationary PTO operation of extended duratio...

• The Total Accessory Reserve Capacity (TARC) is shown on the lowerright side of the vehicle’s Safety Compliance Certification Label. Thisapplies to Ford-completed vehicles of 10,000 lb. (4,536 kg) GVWR orless. This is the weight of permanently-attached auxiliary equipment,such as snowplow frame-mou...

Snowplowing with your airbag-equipped vehicle Your vehicle is equipped with a driver and passenger airbagSupplemental Restraint System (SRS) The SRS is designed to activate incertain frontal and offset frontal collisions when the vehicle sustainssufficient longitudinal deceleration. Careless or high...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on: Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio i...

FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fuel to theengine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you mayrestart your vehic...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Not used (spare) 2 15A Upfitter relay #4 3 30A Not used (spare) 4 10A Telescoping mirror switch, Interiorlights, Hood lamp 5 20A Moon roof 6 5A Driver seat module 7 7.5A Driver seat switch, Driver lumbarmoto...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 93 20A* Auxiliary power point #3 94 25A* Upfitter #1 95 25A* Upfitter #2 96 50A* ABS pump 97 40A* Invertor 98 — Not used 99 — Not used 100 25A* Trailer tow turn signals 101 Relay Starter 102 Relay Trailer tow battery charge 103 — Not used 104 — ...

WARNING: Refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, itwill no longer function. Dissimilar spare tire/wheel information WARNING: Failure to follow these guidelines could resul...

• Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability It is not recommended that the vehicle be operated in 4WD modes witha temporary emergency spare tire. If 4WD operation is necessary, do notoperate above speeds of 10 mph (16 km/h) or for dist...

Spare tire information Note: If your vehicle is equipped the tire pressure monitoring system (TPMS), the system indicator light will illuminate when the spare is inuse. To restore the full functionality of the TPMS system, all road wheelsequipped with the tire pressure monitoring sensors must be mou...

Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their locations: Tool Location Spare tire (pick-up trucks only) Under the vehicle, just forward ofthe rear bumper Jack Regular cab and Crew Cab:Fastened to f...

1. Turn engine off and block thewheel that is diagonally opposite ofthe flat tire using the wheel chock,if equipped. If the vehicle is a 4x4, lock the manual hub on the wheel. 2. Remove the jack, jack handle, lug wrench and spare tire from thestowage locations. 3. Use the tip of the lug wrench to re...

• Front: F–450/F–550 • Rear: F-350 DRW • Rear: F-450/F-550 13. Insert the jack handle into thepump linkage. 14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed ...

16. Replace the flat tire with the spare tire, making sure the valve stemis facing outward on all front an inboard rear wheels. If replacing theoutboard wheel, the valve stem must be facing inward. Reinstall the lugnuts until the wheel is snug against the hub. Do not fully tighten the lugnuts until ...

WHEEL LUG NUT TORQUE SPECIFICATIONS On vehicles equipped with single rear wheels, retighten the lug nuts tothe specified torque at 500 miles (800 km) after any wheel disturbance(tire rotation, changing a flat tire, wheel removal, etc.). On vehicles equipped with dual rear wheels, retighten the wheel...

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot surface (1...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables Note: In the...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that the vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbe...

Note: Towing an ESOF 4x4 vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatictransmission. Note: Towing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph(56 km/h) may c...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with...

• 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Ta...

INSTRUMENT PANEL AND CONSOLE (HARLEY-DAVIDSON ONLY) Your vehicle’s instrument panel and console are uniquely painted withboth high and low gloss paints that require special care. The high glossarea is similar to that of the vehicle’s exterior; the low gloss area isdesigned to help protect the driver...

• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. WARN...

For routine cleaning, wipe the surface with a soft, damp cloth. For morethorough cleaning, wipe the surface with a mild soap and water solution. • Clean spills as quickly as possible. • Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather. • Do ...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your authorized dealer has many quality products available to clean yourvehicle and protect its finishes. These quality products have beenspecifically engineered to fulfill your automotive needs; they are customdesigned to complement the style and appearan...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has many sharp edges and can damage the micro edge of thewiper rubber element. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance ...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford pro...

Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner may adversely affectbattery performance and durability. WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted subst...

6. Release the parking brake. With your foot on the brake pedal and withthe A/C on, put the vehicle in D (Drive) and allow the engine to idle forat least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the id...

• Protection against rust and other forms of corrosion. • Proper function of calibrated gauges. When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine cool...

WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. DO NOT MIX recycl...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. If your vehicle is equipped with a diesel engine, refer to the Maintenance product specifications and capacities section of your diese...

WARNING: Never remove the coolant reservoir cap while the engine is running or hot. 4. If the coolant level is normal, you may restart your engine andcontinue on. 5. If the coolant is low, add coolant, restart the engine and take yourvehicle to an authorized dealer. See Adding engine coolant in this...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels such as gasoline and ethanol are highlytoxic an...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise,fuel may spray out and injure you or others. WARNING: If you do not use the proper fuel filler cap, ex...

Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with a pump(R+M)/2 octane rating of 87. Some stations offer fuels posted as“Regular” with an octane rating below 87, particularly in high altitudeareas. Fuels with octane levels below 87 are not recommended. Do not be...

Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating. These products have not been approved for your engine andcould cause damage to the fue...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

POWER STEERING FLUID Check the power steering fluid. Refer to scheduled maintenance information. If adding fluid is necessary, use only MERCON 威 ATF. • Gasoline engine shown; dieselengine similar. Refer to Identifying components in theengine compartment in the diesel supplement. Check the fluid leve...

BRAKE FLUID • Vacuum boost system • Hydroboost system The fluid level will drop slowly as the brakes wear, and will rise when thebrake components are replaced. Fluid levels between the top of the MINand MAX lines are within the normal operating range; there is no need toadd fluid. If the fluid level...

TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to the Maintenance product ...

The following procedure is for vehicles equipped with a gasoline engine.If your vehicle is equipped with a diesel engine, refer to the dieselsupplement. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Lo...

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (connector shownfrom below for clarity). Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty ma...

Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking parts and prevent corrosion. Removing vehicle from storage When your vehicle is ready to come out of storage,...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty cove...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company. Depending on the plan you purchase,Ford ESP provides benefits such as: • Rental reimbursement...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle.Carefully following this schedule helps protect against major repairexpenses resulting from neglect or inadequate maintenance and may alsohelp to increase the value of ...

Non-Ford approved chemicals or additives are not required for factoryrecommended maintenance. In fact, Ford Motor Company recommendsagainst the use of such additive products unless specificallyrecommended by Ford for a particular application. Oil, fluids and flushing In many cases, fluid discolorati...

Value shopping for your vehicle’s maintenance needs Your dealership recognizes the competitive landscape of maintenance andlight repair automotive services. With factory-trained technicians, andone-stop service from routine maintenance like oil changes and tirerotations to repairs like brake service...

Multi-point inspection Ford recommended scheduled maintenance – In order to keep yourvehicle running right, it is important to have the systems on your vehiclechecked regularly. This can help identify potential issues and preventmajor problems. Ford Motor Company recommends the followingmulti-point ...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) intervals with exceptions noted. Scheduled Maintenance Guide 419 2011 F-250/350/450/550 (f23) Owners Guide, 1st PrintingUSA (fus)

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below, you will need to have some items maintained more frequently. If you only occasionally operate your vehicle under these conditions, it is not...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery Inspect frequently, service as required – Replace cabin air filter (if equipped). – Replace engine air filter. Every 5,000 miles (8,000 km) – Inspect brake system.– Ro...

Off-road operation Inspect frequently, service as required – Replace cabin air filter (if equipped). – Replace engine air filter.– Inspect and lubricate steering linkage ball joints andU-joints (if equipped with grease fittings). Every 5,000 miles (8,000 km) or 6 months – Change engine oil and repla...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal Vehicle Axle Maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-designaxles are lubricated for life. These lubricants...

COOLANT CHANGE RECORD Hot Climate Oil Change Intervals ❑ If operating conditions are normal and you drive your Ford, Lincoln or Mercury vehicle under typical, everyday conditions and you are using an API performance category oil of SL or later (for example SM, etc.) then you can follow the 7,500 mil...

Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M...

A Accessory delay ........................103 AdvanceTrac ..............................268 Air cleaner filter .......394–395, 399 Air conditioning ....................78, 81 manual heating and airconditioning system .................78 Airbag supplemental restraintsystem ........................176...

refill capacities ........................400service points ..................362–364 Engine block heater .................263 Engine oil ..................................366 checking and adding ..............366dipstick ....................................366filter, specifications ........367, 399...

V Vehicle Identification Number(VIN) ..........................................406 Vehicle loading ..........................239 Ventilating your vehicle ...........263 W Warning lights (see Lights) .......14 Washer fluid ..............................365 Water, Driving through .............307 Wind...