Ford 2010 Mustang v.2- Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of their vehicle. Only use cel...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster (V6 shown; V8 similar) Optional instrument cluster (V6 shown; V8 similar) Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists wit...

Service engine soon: The service engine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to indicate whether the vehicle is ready forInspection/Maintenance (I/M) testing. Normally, the service engine soonlight will stay on until the engine is c...

time, contact your authorized dealer as soon as possible. Illuminationafter releasing the parking brake indicates low brake fluid level. Contactyour authorized dealer as soon as possible. WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in brakin...

O/D OFF (automatictransmission): Illuminates when the overdrive function of thetransmission has been turned off;refer to the Driving chapter. If the light does not illuminate, contact your authorized dealer as soon as possible. Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank ...

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is opened. GAUGES Base instrument cluster gauges (V6 shown; V8 similar) Optional instrument cluster gauges (V6 shown; V8 similar) Refer to Message ...

Speedometer: Indicates the current vehicle speed. • V6 instrument cluster • V8 instrument cluster Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, theengine...

Trip odometer: Registers the distance of individual journeys. • Base instrument cluster: Press the reset button to select TripA and Trip B. Press and hold thereset button to reset the tripodometer to zero. • Optional instrument cluster: Press and release the messagecenter INFO button until TRIP Amod...

Engine oil pressure gauge (ifequipped): Indicates engine oil pressure. The needle should stay inthe normal operating range(between “L” and “H”). If the needlefalls below the normal range, stopthe vehicle, turn off the engine andcheck the engine oil level. Add oil ifneeded. If the oil level is correc...

Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP menu. Setup menu Press this control for the followingdisplays: Note: The vehicle’s headlamps or parklamps must be on toperform/check light functions. • System Check • My Color 1, 2, 3 • Oil Life...

The sequence of the system check report and how it appears in themessage center is as follows: 1. OIL LIFE 2. CHARGING SYSTEM 3. ALL DOORS CLOSED 4. DRIVER DOOR 5. PASSENGER DOOR 6. TRUNK 7. SECURITY SYSTEM (if equipped) 8. BRAKE SYSTEM 9. FUEL LEVEL Oil life An oil change is required whenever indic...

Note: Headlamps or parklamps must be on to set up colors. To choose colors for the gauges, halo color or ambient lighting do thefollowing: 1. Press SETUP to reach the GAUGE COLOR, AMBIENT COLOR, orHALO COLOR menu. 2. Press RESET to scroll through the following color options: • Ice Blue • White • Gre...

Warnings that return after the ignition key is turned from off toon: CHECK BRAKE SYSTEM — Displayed when the braking system is not operating properly. If the warning stays on or continues to come on,contact your authorized dealer as soon as possible. LOW TIRE PRESSURE — Displayed when one or more ti...

AUDIO SYSTEMS AM/FM CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary respo...

Setting the clock To set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and minutes. The clock will then beginfrom that time. AM/FM Radio / VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decreas...

CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded, NO DISC will appear in thedisplay. LOAD:For a single CD system– This control is not operational. To load aCD, simply insert the disc, label side up...

TEXT: Press and release to display the artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH) and Category (CA). In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT...

titles, the display will read REPLACE SONG? Press OK to access thesaved titles and press SEEK to cycle through the saved titles. When the song title appears in the display that you would like toreplace, press OK. SONG REPLACED will appear in the display. b. DELETE A SONG: Press OK to delete a song f...

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. The display will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accepts your entry it will displayENTER NEW PIN. Enter your new four-digit PIN and the system willsave the new PIN and PIN SAVED will display. c. UNLOCK A...

Your vehicle is equipped with anauxiliary input jack (AIJ) located inthe center console. The auxiliaryinput jack provides a way to connectyour portable music player to thein-vehicle audio system. This allowsthe audio from a portable musicplayer to be played through thevehicle speakers with high fide...

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also to charge devices ifthey support this feature. Forfurther information on this feature,refer to Accessing and using your USB port in the SYNC 威 supple...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear th...

5. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed tocool down the interior of the vehicle and may also help reduce undesiredodors from reaching the interior of the vehicle. Recirculated air engagesautomatically w...

• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.” During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C mode, adju...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(NAVIGATION BASED – IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. CLIMATE: Press to control the climate control system through the touch display screen. See Touchscre...

TOUCHSCREEN FUNCTIONS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. Temperature: Press the up and down arrows on the left side of the screen to increase/decrease the airflow temperature for the driver side ofthe vehicle. ...

Operating tips • To reduce fog build up on the windshield during humid weather,select (defrost). Temperature and/or fan speed can also be increased to improve clearing. • To reduce humidity build up inside the vehicle: do not drive with thesystem off or with (recirculated air) engaged. • Do not put ...

REAR WINDOW DEFROSTER R Press the control to clear the rear window of thin ice and fog. The LEDwill illuminate. The rear window defroster turns off automatically after 15 minutes, orwhen the ignition is turned off. To manually turn off the defroster before15 minutes have passed, press the control ag...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Automatic instrumentation illumination When the headlamps or parking lamps are switched on, a light sensor inyour vehicle monitors the outside...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parking lampoperation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Move the controldown, past detent, to turn off theinte...

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. To see a clearer light pattern for adjusting, block thelight from one headlamp while adjusting the other. For vehicles with halogen headlamps: On the wall or screen you willobserve a flat zone of high intensitylight...

5. Then use a 7mm Allen wrench or a Phillips screwdriver to adjust theheadlamp up or down. HORIZONTAL AIM IS NOT REQUIRED FOR THISVEHICLE AND IS NON-ADJUSTABLE. 6. Close the hood and turn off the lamps. TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right ...

Replacing interior bulbs Check the operation of all bulbs frequently. Replacing exterior bulbs Check the operation of all bulbs frequently. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in the off position, then open the hood. 2. Disconnect the electricalconne...

Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the off position and open thehood. Halogen headlamp HID headlamp 2. Remove the hex head screws attaching the underbody forwardaeroshield and remove to gain access to the front parking lamp/ turnsignal assembly. 3....

3. Unbolt the three tail lampattachment nuts and remove thelamp assembly. 4. Rotate the LED assemblycounterclockwise and remove itfrom the lamp assembly. 5. Disconnect the LED assemblyfrom the electrical connector andreplace the LED assembly. 6. Install new LED assembly inreverse order. Replacing ba...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

TILT STEERING WHEEL To adjust the steering wheel: 1. Push the lever down to unlockthe steering column. While the leveris in the down position, tilt thesteering column to its desiredorientation. 2. While holding the steeringcolumn, pull the lever up to itsoriginal position to lock the steeringcolumn....

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang any type of accessory oraccessory bracket from the plug. Improper use of the poweroutlet can cause damage ...

Bounce-back override (front windows only) To override bounce-back, within two seconds after reaching bounce-backposition, if the switch is moved from the neutral to the express-upposition the window will travel up with no bounce-back protection. If the switch is released before the window reaches fu...

In the event that the rear quarter window switch does not operate whenthe convertible top is completely up or down, the rear quarter windowscan be manually raised up. The following procedure must be performed within two minutes: 1. Turn the ignition key to the off position, then turn back to the onp...

Note: If equipped with a rearview camera system, a video image will be displayed in the mirror or the navigation system display (if equipped)when the vehicle is put in reverse. Refer to Rearview camera system in the Driving chapter. EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1....

2. Accelerate to the desired speed. Base controls Optional controls 3. Press the SET (+) control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down asteep hill...

Resuming a set speed Base controls Optional controls Press the RES / RESUME control and release it. This will automaticallyreturn the vehicle to the previously set speed. Increasing speed while using speed control Base controls Optional controls There are two ways to set a higher speed: • Press and ...

Reducing speed while using speed control Base controls Optional controls There are two ways to reduce a set speed: • Press and hold the SET (-) control until you get to the desired speed,then release the control. You can also use the SET (-) control tooperate the Tap-Down function. Press and release...

4. Press the convertible top switchon the overhead console and holduntil the windows are completelydown and the top is completelystored. Installation of the boot (if equipped) Be sure the boot is secure on the vehicle before driving. 1. Install the boot on the vehicle by hooking the boot retaining c...

4. Tuck the boot corners behind the shoulder belts. 5. Secure the boot straps on the rear seat hooks behind the rear seat. Note: Improper installation can result in loss and/or damage ofthe boot while driving. WARNING: Always secure the retaining clips and boot straps on the vehicle or the boot may ...

3. Fold the right side inward and secure the boot with the strap.Stow the boot in the trunk. Raising the convertible top The convertible top will not operate unless the vehicle is traveling under 3 mph (5 km/h).To raise the convertible top:1. Bring the vehicle to a complete stop. Key must be in the ...

The latch handles must be pulled downwards fully to allow thelatch to fully rotate into the closed position. 5. Secure the driver’s side latch firstthen secure the Passenger side. Pulldown firmly on the latch handlesbefore rotating them into thewindshield header until they reachthe full forward posi...

INTERIOR TRUNK CONTROL The remote trunk release button islocated on the instrument panel.Press the button to unlatch thetrunk. Interior trunk control lockout (convertible vehicles only) This feature helps prevent unauthorized access to the trunk when theconvertible top is open, by disabling the inte...

KEYS Your vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle andunlocks/locks all the doors. Thetransmitter portion functions as theremote entry transmitter. Your IKTs are programmed to your vehicle; using a non-p...

6. To enable/disable the autounlock feature, press the lock control, thenpress the unlock control. The horn will chirp once if autounlock wasdeactivated or twice (one short and one long chirp) if autounlock wasactivated.7. Turn the ignition to the off position. The horn will chirp once toconfirm the...

WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people oranimals to these high temperatures for even a short time can causedeath or serious heat-related injuries,...

In the event of battery failure, youcan open the trunk on theconvertible by using your masterkey in the key cylinder between the seat cushion located in theback seat on the driver’s side. Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or ...

Replacing lost Integrated Keyhead Transmitters (IKTs) If you would like to have your Integrated Keyhead Transmittersreprogrammed because you lost one, or would like to buy additionalIKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to rep...

started unless a coded Integrated Keyhead Transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded Integrated Keyhead Transmitters;additional coded IKTs may be purchased from your authorized dea...

9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’sengine and will operate the remote entry system (if the new key is anIntegrated Keyhead Transmitter). The theft indicator light will illuminatefor three seconds and then...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion ofyour Integrated Keyhead Transmitter. • Turn ignition to the on position with a valid programmed SecuriLock 威 key or Integrated Keyhead Transmitter (IKT)....

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front manual seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Always drive and ride with your seatback upright an...

To operate the heated seats: • Press control to activate. • Press again to deactivate. The heated seats will only function when the engine is running. Rear seat entry/exit Use the seatback release to fold theback of the front seat forward forrear seat access. This release handleis located on the upp...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, like infantsin rear-facing child seats, this occurs because the...

Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly against the occupant’s bodyduring frontal collisions, and in side collisions. This helps increase theeffectiveness of the safety belts. In frontal coll...

WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts The presenter arm (available on the coupe only) is intended to improveaccess to the safety belt and to allow access to the rear seat. R...

WARNING: Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. The front and rear safety restraints in the vehicle are combination lapand shoulder belts. The front passenger and rear seat safety belts havetwo types of locking modes described below: Vehic...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode WARNING: Ford Motor Comp...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions. The safety belt pretensioner tightens the safety belts firmly against theoccupant’s body at the start of the crash. WARNING: The driver and front passenger sa...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s airbagsystem. Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are...

2. Wait until the safety belt warning light turns off (Approximately oneminute). • Step 3 must be completed within 30 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, buckle then unbuckle thesafety belt three times at a moderate speed, ending in the u...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. WARNING: All occupants of the vehicle, including the driver, s...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the airbag sensors to closean electrical circuit that initiatesairbag inflation. The fact that theairbags did not inflate in a collisi...

• one or more impact and safing sensors • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components • Front safety belt pretensioner • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag o...

• the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions, • the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period oftim...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

WARNING: Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback. WARNING...

Side airbags, in combination with safety belts, can help reduce the risk ofsevere injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe co...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is ...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddler seat). Small...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol. The LATCH anchors are located atthe rear section of the rear seatbetween the cushion and seat back,below the locator symbols on theseat back. Follow the child seatmanufacturer’...

Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether anchor, if applicable. Tug thechild seat from side to side and forward and back where it is secured tothe vehicle. The seat should move less than one inch when you do thisfor a proper installat...

The tether strap anchors in your vehicle are in the following positions(shown from top view): Attach the tether strap only to theappropriate tether anchor as shown.The tether strap may not workproperly if attached somewhereother than the correct tetheranchor. Once the child safety seat has beeninsta...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thiscondition. Do not introduce any item thicker than this under the boosterseat. Check with the booster seat manufacturer’s instructions. The importance of shoul...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tir...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label, which is located on the B-Pillar or the edge of thedriver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction and Tempe...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The Tire Pressure Monitoring System is NOT a substitute for manually checking tire pressure. The ...

To restore the full functionality of the Tire Pressure Monitoring System,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with TPMS in this section. When you believe your system is not operating properly The main function of ...

Low Tire PressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is inuse. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a description ofhow the system functions underthese conditio...

SNOW TIRES AND CHAINS WARNING: Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. WARNING: Snow tires must be the same size, load index, speed rating as those origina...

SUMMER TIRES Your Ford vehicle may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and Snow (M+S or M/S) tire traction rating on the tire sidewall. Since summer tires do not have the same traction performance asAll-season or Snow tir...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, thenthe load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now yo...

Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cross thechains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agen...

eliminate excessive downshifting and upshifting for optimum fueleconomy and transmission cooling. • Anticipate stops and brake gradually. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance info...

STARTING Positions of the ignition 1. Off — locks the automatictransmission gearshift lever andallows key removal. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. Accessory — allows the electricalaccessories such as the radio to...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel until thekey turns freely. 2. Turn the key to 4 (start), thenrelease the key as soon as theengine starts. Note: If the engine does not start within fi...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

When an event occurs that activates AdvanceTrac 威 you may experience the following: • A slight deceleration of the vehicle • The “sliding car” indicator light will flash. • A vibration in the pedal when your foot is on the brake pedal • If the driving condition is severe and your foot is not on the ...

Sport mode is not intended for use on public roadways as this modeprovides less AdvanceTrac 威 system intervention than when the default ESC and Traction Control systems are on. Sport mode will allow morespirited driving while the AdvanceTrac 威 system is still enabled. STEERING To help prevent damage...

BRAKE-SHIFT INTERLOCK This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the on position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Park) with ignition inthe on ...

WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. Contact your authorized dealer as soon as possible tohave the system serviced immediately. AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Understanding the gearshi...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

3 (Third) This position allows for third gear only. • Provides engine braking. • To return to D (Drive) without Overdrive, move the transmission shiftlever into the D (Drive) position. • Selecting 3 (Third) at higher speeds will cause the transmission todownshift to third gear at the appropriate veh...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is fully pressed. To start the vehicle: 1. Make sure the parking brake isfully set. 2. Press and hold the clutch pedalto the flo...

Recommended shift speeds Do not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 11 mph (18 km/h) 2 - 3 19 mph (31 ...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system,located on the trunk, provides avideo image which appears in therearview mirror or on the navigationscreen (if equipped), of the areabehind the vehicle. It addsassistance to the driver whilereversing or reverse parking thevehicle.To use...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF SWITCH FUEL RESET This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the dr...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 80A* Passenger compartment fusepanel 2 — Not used 3 — Not used 4 30A...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (...

• Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle. Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operati...

• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation. What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stageswith the temporary mobility kit: • In the first stage, the tire will be reinfla...

4. Plug the power cable into the 12Vpower point in the vehicle. 5. Remove the warning sticker found on the canister and place it on thetop of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) . 7. Turn dial (1) counterc...

tire pressure has to be checked with the compressor in the OFFposition to get the correct tire pressure reading. WARNING: Do not stand directly over the temporary mobility kit while inflating the tire. If you notice any unusual bulges or deformations in the tire’s sidewall during inflation, stop and...

4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jam area. Note: The tire pressure has to be checked with the compressor in theOFF position to get the correct tirepressure reading. 5. Turn the compressor off bypressing the on/off button. ...

Removal of the Sealant Canister from the Temporary Mobility Kit 1. Unwrap the clear tube from thecompressor housing. 2. Locate the yellow cap at the endof the clear tube. 3. Using the yellow cap tool, pressthe tab located on the temporarymobility kit compressor housingwhile pulling up on the sealant...

Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorizeddealer for assistance. Be sure to check the sealantcompound’s “use by” date regularly.The “use by” date is on the lowerright hand corner of the labellocated on...

Note: Inspect the wheel pilot hole prior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot sur...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

4.6L 3V V8 ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remover...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft 威 Premium Windshield Washer Concentrate (ZC-32-A), available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade an...

• Do not use household or glass cleaners as these may damage thefinish of the instrument panel, interior trim and cluster lens. WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. If a staining l...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING:...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, press and hold the clutch pedal, place thegearshift in N (Neutral), and release the clutch pedal. 2. Block the wheels. WARNING: T...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box Main...

Engine shield Some vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter changes. It is secured withfour screws. WINDSHIELD WASHERFLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the ...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

5. Locate and carefully remove the engine oil level dipstick. • 4.0L V6 engine • 4.6L V8 engine 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. Maintenance and Specifica...

• If the oil level is below the lower hole, add enough oil to raise thelevel within the lower and upper holes. • 4.0L V6 engine • 4.6L V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the dipstick back in and...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil according to the appropriate schedule listed inthe scheduled maintenance information. Ford production and...

Change your engine oil according to the appropriate schedule listed inthe scheduled maintenance information. Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and design...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

transmission may shift firmly. This operation is considered normal andwill not affect function or durability of the transmission. Over time theadaptive learning process will fully update transmission operation to itsoptimum shift feel. If the battery has been disconnected or a new battery has been i...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interval s...

WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Severe climates If you drive in extremely cold climates (less than –34°F [–36°C]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection char...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft 威 part. The customer warranty may be void for any damage to the fuel syste...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuelfiller nozzle. The overfilled fuel may run down the drain located withinthe fuel filler housing and to the ground. If the check fuel fill inlet light or...

Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may notbe covered under warranty. Octane recommendations...

Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask your fuel supplier about gasolines that meet theWorld-Wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the ...

1. Locate the white plastic funnel. Itis included with the tire changingtools. (For vehicles equipped withthe temporary mobility kit, thefunnel is located in the spare tirewell in the trunk). 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel...

vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior t...

WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the service engine soon indicator, charging system warning light or the temperature warning light,...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If t...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Note: There are two different manual transmissions used in thisvehicle and they have different fluid levels. For vehicles equipped with aV6 engine, the corr...

• Fill level for V6 • Fill level for V8 4. Add enough fluid through the filler opening to bring the fluid up tothe recommended levels. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Maintenance product specifications and capacities in this chap...

Changing the air filter element V6 V8 1. Release the clamps that secure the air filter housing cover. 2. Remove the air filter element from the air filter housing. 3. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 4. Install a new air filter eleme...

MOTORCRAFT PART NUMBERS Component 4.0L V6 engine 4.6L V8 engine Air filter element FA-1773 FA-1897 Fuel filter FG-1083 FG-1083 Battery BXT-96R BXT-96R Oil filter FL-820-S FL-820-S Spark Plugs 1 1 For spark plug replacement, see your authorized dealer. Refer to scheduled maintenance information for t...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................79 AdvanceTrac ..............................198 AdvanceTrac Sport Mode .........203 Air cleaner filter ...............294–296 Air conditioning ....................51, 54 manual heating and airconditioning system .................51 Airbag supplemental res...