Ford 2010 Focus v.2- Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide/Customer Information Guide that is provided to you along with your Owner’s Guide. Special instructions For you...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving ...

Airbag readiness: If this light fails to illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediately by your authorized dealer. A chime will soundwhen there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety b...

Overdrive off (if equipped): Illuminates when the overdrivefunction of the transmission hasbeen turned off, refer to the Driving chapter. If the light flashes steadily or does not illuminate, have the transmission serviced soon, or damage may occur. Speed control (if equipped): Illuminates when the ...

Throttle Control/Transmission: Illuminates when a powertrain faulthas been detected. Contact yourauthorized dealer as soon aspossible. Low fuel: Illuminates when the fuel level in the fuel tank is at or nearempty (refer to Fuel gauge in this chapter). Door ajar: Illuminates when the ignition is in t...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range. If it enters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, s...

Odometer: Registers the total miles (kilometers) of the vehicle. If equipped with a message center,refer to Message center in this chapter on how to switch thedisplay between Metric and English. Trip odometer: Registers the distance of individual journeys. • Standard instrument cluster: Press the SE...

MESSAGE CENTER Your vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicle problems and variousconditions with an informational message followed by a long indicatorchime. The message center display is located in the instrument cluster. Info Pres...

RESET FOR SYSTEM CHECK When this message appears, press the RESET button and the messagecenter will begin to cycle through the following systems and provide astatus of the item if needed. 1. CHARGING SYSTEM 2. DOORS 3. TRUNK 4. BRAKE SYSTEM 5. DTE/FUEL LEVEL 6. MYKEY DISTANCE (if programmed) 7. MYKE...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for fourseconds. The message center will display the l...

AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM/single CD satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. F...

In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT and thenpress SEEK/TRACK to view the additional display text. CAT (Category) / FOLD (Folder): Press to switch between turning the most recently selected satellite radio ...

The song will appear in the display for confirmation. Press OK againand the display will read SONG DELETED. If you do not want todelete the currently listed song, press / to select either RETURN or CANCEL. Note: If there are no songs presently saved, the display will read NO SONGS. c. DELETE ALL SON...

d. RESET PIN: Press OK when RESET PIN is displayed. The display will read ARE YOUR SURE. Press OK again to automatically reset thePIN number to its initial password setting (1234). PIN RESET TODEFAULT PIN will be displayed. e. RETURN: Press OK when RETURN is displayed and the system will exit back t...

To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off. 3. Attach one end of the audio extension cable to the headp...

location, such as the center console or the glove box, when the vehicle isin motion. The audio extension cable must be long enough to allow theportable music player to be safely stored while the vehicle is in motion. USB port (if equipped) WARNING: Driving while distracted can result in loss of vehi...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. R Rear defroster: Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this chapter for more information. 3. Defrost: Distributes ou...

9. Temperature control: Controls the temperature of the airflow in the vehicle. 10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter. 11. Recirculated air: Press to activate/deactivate a...

During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C in theMAX A/C position, reduce blower fan speed from the highest setting andput the vehicle’s transmission into the PARK gear position (automatictransmission only) to...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Fog lamp control (if equipped) The fog lamps can be turned onwhen the headlamp control is inthe or position and the high beams are not turned ...

Rear dome lamp When the lamp control is in themiddle position, the rear dome lampwill come on when a door is openedor the unlock button is pressed onthe remote keyless entry. If the control is moved to the driverside position, the lamp will not comeon at all. If the control is moved to the passenger...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down until you find thedesired position. 3. While holding the steering wheelin place, pull the lever up to itsoriginal positi...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

Window lock (if equipped) The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. INTERIOR MIRROR The interior rear view mirror has tw...

EXTERIOR MIRRORS Power side view mirrors (if equipped) WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the direc...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

• Press the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off thespeed control: • Press the speed control OFFcontrol. • Turn off the ignition. Note: When you turn off the speed control or the ignition, your speedco...

To vent the moon roof: Press and release the TILT control, the moon roof will move to the vent position automatically from any moon roofposition. Press the switch again to stop the moon roof. Pull and hold theTILT control to close the moon roof. The moon roof has a built-in sliding shade that can be...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

• The AdvanceTrac 威 system cannot be turned off. When this optional setting is on, the MyKey™ user will not be able to deactivate thesystem. Note: It may be beneficial to deactivate the AdvanceTrac 威 system if the vehicle is stuck in snow, mud, or sand. Create a MyKey™ To program MyKey™ on one of th...

Using MyKey™ with Remote Start Systems MyKey™ is not compatible with non-Ford approved aftermarket remotestart systems. If you choose to install a remote start system please seeyour authorized dealer for a Ford approved remote start system. When using a Ford-approved remote start system, the default...

Troubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in the ignition is already a MyKey™ • Key in the ignition is the last remaining Admin key (there alwayshas to be at least one Admin key) • SecuriLock 威 passive anti-theft system is disabled or in unlimitedmode • Vehicle has been ...

Power door unlock/lock procedure Before starting, ensure the ignition is in the off position and all vehicledoors are closed. You must complete Steps 1–5 within 30 seconds or theprocedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 30 seconds before beginning ag...

• Ensure that the trunk is closed and latched before driving yourvehicle. Failure to properly latch the trunk may cause objects to fallout or block the driver’s rear view. Replacing the battery The remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent. To replace...

How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. If all remote entry transmittersare not present during the programming procedure, the transmitters thatare not present during programming will no l...

The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit • When all vehicle doors and the trunk are closed, and the key isremoved from the ignition, the interior lamps and parking lamps willilluminate. The lamps will turn off if all...

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the samekey chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded key while starting the engine. Theseobjects will not cause dama...

Programming spare keys You can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 威 keys. • You must have two previously programmed coded keys (keys thatalre...

If the key has been successfully programmed it will start the vehicle’sengine and the theft indicator light will illuminate for three seconds andthen go out. If the key was not successfully programmed, it will not start yourvehicle’s engine and the theft indicator light will flash on and off, or sta...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Unlock the doors with a key. Turn the key full travel (toward the frontof the vehicle) to ensure the alarm disarms. • Turn the ignition to th...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front manual seat WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of th...

Tip/slide front passenger seat (if equipped) Lift the control and fold theseatback forward. The seat can be slid forward toallow easier entry to the rear seats.Slide the seat back and fold backthe seatback until it locks with adistinct click. Rock the seat toensure that the catch is securelyengaged....

Lower the head restraint bypressing and holding the guidesleeve release button and pushingdown on the head restraint. For details about the individual components of the head restraints andabout how to remove the head restraints, refer to Adjustable head restraints at the beginning of this chapter. F...

SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System™ provides an improved overall level offrontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and crash ...

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbaginflation energy. A lower, less forceful energy level is provided for morecommon, moderate-severity impacts. A higher energy level is used forthe most severe impact...

The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint us...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, frontpassenger sensing system, and the driver seat position sensor. Inaddition, the RCM also mon...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle. Energy management feature • This vehicle has a safety belt system with an energy managementfeature at the front outboard seating positions to help further reducethe risk of injury in the event of a head-on collision. • Thi...

Safety belts with locking cinch tongue (rear center position only) The locking cinch tongue will slide up and down the belt webbing whenthe belt is in the stowed position or while putting safety belts on. Whenthe locking cinch tongue of the lap/shoulder combination safety belt islatched into the buc...

WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belton the outside shoulder only. Never wear the shoulder belt under thearm. 2) Never swing the safety belt aro...

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the sa...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• safety belt pretensioners • one or more impact and safing sensors. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this chapter. • a readi...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

WARNING: If the side air curtain has deployed, the air curtain will not functionagain. The side air curtainsystem (including the A, B andC pillar trim and headliner)must be inspected and servicedby an authorized dealer. If the air curtain is not replaced, theunrepaired area will increase therisk of ...

The feature will continue to operate until the vehicle runs out of power. Disposal of airbags and airbag equipped vehicles(including pretensioners) Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Attach the tether strap afterward, if included with the child seat. Referto Recommendations for attaching child safety restraints for children in this chapter. Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap whichextends from the back of ...

2. Locate the correct anchor for theselected seating position. 3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat te...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires, Wheels and Loading 167 2010 Focus (foc) O...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

Front Wheel Drive (FWD) vehicles with manual transmissions: If your vehicle is equipped with a manual transmission, shifting thetransmission into neutral (N) permits “flat-towing” (all wheels on theground) for pulling behind a motorhome. Before you tow your vehicle: • Release the parking brake. • Mo...

STARTING Positions of the ignition 1. Off — locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Thisposition also shuts the engine andall electrical accessories off. 2. Accessory—allows the electricalaccessories such as the radio tooperate while the engine is notru...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). 2. Turn the key to 4 (start), thenrelease the key as soon as theengine begins cranking. Your vehiclehas a computer assisted crankingsystem that assists in starting theengine. After releasing the key fromthe 4 (start) ...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an anti-lock braking system (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. WARNIN...

Switching Off Traction Control If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the TCS feature of the AdvanceTrac 威 system may be beneficial because the wheels are allowed to spin. This will restorefull engine power and will enhance momentum through the obs...

If the steering wanders or pulls, check for: • An improperly inflated tire • Uneven tire wear • Loose or worn suspension components • Loose or worn steering components • Improper steering alignment A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. BRAKE-SHIFT...

WARNING: Do not drive your vehicle until you verify that the brakelamps are working. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: If the parking brake...

D (Drive) without Overdrive Overdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever. • This position allows for allforward gears (1–3) exceptoverdrive. • Provides engine braking. • Use when driving conditionscause excessive shifting from O/Dto other g...

Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to thetransmission and tires may occur, or the engine may overheat. MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clut...

Recommended shift speeds Do not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Recommended upshifts (for best fuel economy) when accelerating 5-speed manual transmission Shift from: 1 - 2 14 mph...

Removing the key Turn the ignition to position 1 (off) and remove the key. DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or t...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

Note: With extended use, the flasher may run down your battery. FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activat...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Protected circuits 40 20A Not used (spare) 41 15A Door lock/sunroof switchillumination, Auto dimming rearview mirror, Ambient lighting 42 10A Not used (spare) 43 10A Not used (spare) 44 10A Not used (spare) 45 5A Front wipers (logic) 46 7.5A Front passenger sensin...

CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that isdifferent in one or...

• Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and...

Tire change procedure WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatictransmission) or R (Reverse) (manual transmission). WARNING: To help prevent the vehic...

3. If equipped with a 6-spoke wheelcover that’s bolted on, remove thefour plastic nuts by turningcounterclockwise 1/4 turn for accessto the lug nuts. Note: To avoid damage to the wheel cover, the 6-spoke wheel covercannot be removed until the tire isoff the vehicle. 4. Loosen each wheel lug nutone-h...

WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is onlymeant for changing the tire. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with t...

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the rotor to the hub are secured so they do ...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and aff...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, press and hold the clutch pedal, place thegearshift in N (Neutral), and release the clutch pedal. 2. Block the wheels. WARNING: T...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine oil filler cap 2. Brake/Clutch fluid reservoir 3. Power distribution box 4. Battery 5. Air filter 6. Automatic transmission fluid dipstick (if equipped) 7. Engine oil dipstick 8. Power steering fluid reservoir 9. Engine coolant reservoir 10....

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the eng...

Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

When the battery is disconnected or a new battery installed, theautomatic transmission must relearn its adaptive strategy. As a result ofthis, the transmission may shift firmly when first driven. This operation isconsidered normal and will fully update transmission operation to itsoptimum shift feel...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interval s...

WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. DO NOT MIX recycl...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

At the next opportunity, safely pull off of the road, remove the fuel fillercap, align the cap properly and reinstall it. The check fuel caplight or “check fuel cap” message may not reset immediately; it may take several driving cycles for the check fuel cap light or “check fuel cap” message to turn...

Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may notbe covered under warranty. Octane recommendations...

Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still pres...

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to changea number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually gi...

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bugdefl...

If the service engine soon indicator is on or the bulb does not work, the vehicle may need to be serviced. Refer to the On boarddiagnostics (OBD-II) description in this chapter. If the vehicle’s engine or transmission has just been serviced, or thebattery has recently run down or been replaced, the ...

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If t...

6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluidlevel is at the bottom of the dipstickand t...

If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condition oftransmission fluid may causeshift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may...

Changing the air filter element 1. Release the clamps that securethe air filter housing cover.2. Carefully separate the two halvesof the air filter housing.3. Remove the air filter elementfrom the air filter housing.4. Wipe the air filter housing andcover clean to remove any dirt ordebris and to ens...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A AdvanceTrac ..............................181 Air cleaner filter ...............258–259 Air conditioning manual heating and airconditioning system .................42 Airbag supplemental restraintsystem ........................110, 119, 121 and child safety seats ............112description ..........