Ford 2010 Flex - Manuals

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions couldresult in ...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Powertrain malfunction/reducedpower: Illuminates when a powertrain or a AWD fault has beendete...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be checked. Referto Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will illuminate for...

MESSAGE CENTER Your vehicle’s message center allows you to configure/personalize certainvehicle options to suit your needs. The message center is also capable of monitoring many vehicle systemsand will alert you to potential vehicle problems and various conditionswith an informational message follow...

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic...

System check and vehicle feature customization Press SETUP repeatedly to cyclethe message center through thefollowing features: RESET FOR SYSTEM CHECK When this message appears, press RESET and the message center willbegin to cycle through the following systems and provide a status of theitem if nee...

TRAILER SWAY CONTROL (if equipped) This feature uses the electronic stability control to mitigate trailer sway, Press RESET to turn it off or on. CREATE MYKEY / MYKEY SETUP/ CLEAR MYKEY For more information refer to MyKey™ in the Locks and Security chapter. LANGUAGE = ENGLISH / SPANISH / FRENCH Allo...

AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford...

CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded, NO DISC will appear in thedisplay. LOAD:For a single CD system– This control is not operational. To load aCD, simply insert the disc, label side up...

TEXT: Press and release to display the artist and song title. While inTEXT MODE, press again to scrollthrough the Artist (AR), Song (SO), Channel (CH) and Category (CA). In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT...

titles, the display will read REPLACE SONG? Press OK to access thesaved titles and press SEEK to cycle through the saved titles. When the song title appears in the display that you would like toreplace, press OK. SONG REPLACED will appear in the display. b. DELETE A SONG: Press OK to delete a song f...

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. The display will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accepts your entry it will displayENTER NEW PIN. Enter your new four-digit PIN and the system willsave the new PIN and PIN SAVED will display. c. UNLOCK A...

Extra Features AUX: Press repeatedly to cycle through LINE (auxiliary audiomode), SYNC 威 (if equipped) and FES modes (if equipped). For location and further information on auxiliary audio mode, refer to Auxiliary input jack later in this chapter. If your vehicle is equipped with SYNC 威 , refer to th...

The Auxiliary Input Jack provides away to connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To achieve optimalperformance, please observe thefollowing instructions whenattachi...

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also to charge devices ifthey support this feature. Forfurther information on this feature,refer to Accessing and using your USB port in the SYNC 威 supple...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Quick start Your family entertainment system includes two headrest-mounted DVDplayer/screens, two sets of wireless infrared (IR) headphones and awireless infrared (IR) remote control capable of controlling either DVDplayer. Both DVD players are capable of playing their own independentmedia, or they ...

DVD player controls 1. / (Play/Pause): Press to play or pause a CD, DVD or flash/thumb drive track.2. (Stop): Press to stop the current DVD, CD/MP3, or flash/thumb drive track.3. (Eject): Press to eject a disc from the DVD system. 4. MENU: When playing a DVD, press MENU to enter the DVD disc (root) ...

5. / (Headphones/Speakers): Press to activate dual play mode on either headrest system. During dual play mode, the following happens: a. Rear speakers turn off b. Headphones become active on both headrest systems. c. Media sources become available through the DVD systems. Note: If the system is in d...

Remote control Unless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the player.Ensure that there are no obstructions between the remote and player.Press the MON A B control to select either Monitor A or Monitor B. Note: Each h...

4. RETURN: Press to return to the previous menu screen. 5. SETUP : Press to access the setup menu for each monitor. Refer to Setup Menu later in this section for more information. 6. MON A/B: Press to select either monitor A or monitor B to be controlled by the remote control. 7. VOL (Volume): When ...

Battery replacement Batteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails tocontrol the DVD player. Remove the screw and unlatch the battery cover to access the batteries. The remote control unit uses two AAA batteries which...

To install the batteries, remove the screw on the cover and removethe cover. Then, gently lift the topof the cover away from the housingto expose the battery compartment. When replacing the batteries, usetwo new batteries (alkalinerecommended) and install themwith the correct orientation asindicated...

Ensure that the headphones are turned off when not in use. Afterapproximately one minute of not being in use (no infrared signal isreceived), the wireless headphones will automatically turn off. They willalso turn off after two hours of continuous use as a power save feature.If this happens, simply ...

Dual Play: Dual play is when the rear seat passengers choose to listen to a different playing media than the front seat passengers. With theDVD and rear seat controls turned on, the rear seat passengers maychoose to listen to: Monitor A, Monitor B, AM, FM1, FM2 SR1, SR2, SR3(satellite radio, if equi...

Radio interaction: If your vehicle is equipped with a non-touchscreen audio system, you can press AUX on the radio repeatedly until DVDappears in the display. Then, press MENU to access HEADPHONESON/OFF, REAR ZONE CONTROL ON/OFF and other options. Turn theTUNE control to select ON/OFF for HEADPHONES...

Aspect ratio (TV display type) This screen allows you to select theviewing size and shape of the videodisplayed on the LCD screen. This isdisc dependent feature.To access: 1. Press SETUP on the remote to access the menu options. 2. Press / to ’highlight’ the monitor icon. (A disc will appear beneath...

1. Press SETUP on the remote to access the menu options. 2. Press / to ’highlight’ the monitor icon. (A disc will appear beneath the icon signifying it is the current selection.) 3. Press to select and enter the OSD language menu. 4. When OSD Lang is highlighted, press to access the menu. 5. Press /...

4. Press / to chose from Sharpness, Brightness, contrast, color (gamma), hue, saturation and luma-delay. General setup — screen exit To exit the setup screen: 1. Press / to ’highlight’ the “X” icon. (A disc will appearbeneath the icon signifying it is thecurrent selection.) 2. Press ENTER on the rem...

General information Note: DVDs are formatted by regions. US and Canada systems canonly play region 1 DVDs and Mexicosystems can only play region 4DVDs. Systems sold in vehiclestargeted for other parts of the worldwould have different regions. If aplayback problem is encountered,please ensure that yo...

Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln-Mercury couldvoid user’s authority to operate the equipment. This equipment has beentested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. Th...

Foreign substances Exercise care to prevent dirt and foreign objects from entering the DVDplayer compartment. Be especially careful not to spill liquids of any kindonto the media controls or into the system. If liquid is accidentallyspilled onto the system, immediately turn the system OFF and consul...

SINGLE ZONE CLIMATE CONTROL WITH REAR PASSENGERCOMPARTMENT CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog andthin ice. The system will automatically provide outside air to reducewindow fogging....

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with thesystem off or with recirculated air engaged. • Do not put objects under the front seats that will interfe...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS AND REAR PASSENGER COMPARTMENTCLIMATE CONTROL (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Front fan speed control: Press to increase the fan sp...

• : Distributes air through the instrument panel vents. • : Distributes air through the instrument panel vents, floor vents and rear seat floor vents. • : Distributes air through the floor vents and rear seat floor vents. 4. A/C: Press to activate/deactivate air conditioning. Use with recirculated a...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(NAVIGATION BASED–IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Climate: Press to control the climate control system through the touch display screen. See Touchscreen...

TOUCHSCREEN FUNCTIONS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter. Front Zone – Press to activate the touchscreen controls for the front climate system. Temperature – Press the up and down arrows on the left side of the scr...

Max A/C – Distributes recirculated air through the instrument panel vents to cool the vehicle. This re-cooling of the interior air is moreeconomical and efficient. Recirculated air may also help reduceundesirable odors from entering the vehicle. Press MAX A/C again fornormal operation. Rear Zone Pow...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on/off control ofthe exterior lights normallycontrolled b...

3. Turn the ignition switch to on and then back to off. 4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. Fog lamp control (if equipped) With the ignition...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position, • the headlamp control is in the off, autolamps or parking lamp positionand • the transmission must be out of the P (Park) position. WARNING: Always remembe...

Halogen headlamp 5. Locate the vertical adjuster on each headlamp. Using a Phillips #2screwdriver, turn the adjuster either clockwise (to adjust down) orcounterclockwise (to adjust up). The horizontal edge of the brighter lightshould touch the horizontal reference line. 6. Close the hood and turn of...

Note: The ambient lights will stay on until the ignition is placed in the off position and either of the front doors are opened or the accessorydelay timer expires. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a n...

Replacing fog lamp bulbs (if equipped) 1. Make sure the fog lamp switch isin the off position. 2. From underneath the vehicle,partially remove the tire splashshield by removing four drivescrews. After removing to allow free accessto the front fog lamp bulb andelectrical wire harness, the splash shie...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Normal speed operation of rearwiper. 1 — Intermittent operation of rearwiper. 0 (off) — Rear wiper and washer off. For rear wash cycle, rotate (and hold as de...

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamp. Slide on rod feature The visor will slide back and forthon the rod for increased sunlightcoverage. Rotate the visor towardsthe side window and extend itrearward for additional sunlightcoverage. Note: To stow the visor ba...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The door willopen ...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

Second row center console features (if equipped) The second row center consoleincorporates the following features: • Flip forward armrest to provide aflat load floor • Utility compartment • Cupholders • Refrigerator unit (if equipped) inthe utility compartment. Refer to Console refrigerator/freezer....

Refrigerator: Briefly press and hold the COOL side of thecontrol.The indicator light on thecool side of the switch willilluminate and the indicator light onthe freeze side will glow when therefrigerator is active. When in coolmode the temperature will cool toapproximately 41°F (5°C). Brieflypress an...

The power outlet is not designed for the following electric appliances;they may not work properly: • Cathode ray tube type televisions. • Motor loads, such as vacuum cleaners, electric saws and other electricpower tools, compressor-driven refrigerators, etc. • Measuring devices, which process precis...

POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in t...

To operate one-touch up: • Pull the switch completely up tothe second detent and releasequickly. The window will closefully. Momentarily press theswitch to any position to stop thewindow operation. If the switch is pressed and held tothe normal open or one-touch down position during a one-touch upev...

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror Your vehicle is equipped with an inter...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could cause damage to the glass...

WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. The followingbuttons work with speed control: RESUME: Press to resume a set speed. SET +: Press to increase the set spee...

Increasing speed while using speed control To set a higher speed: • Press and hold SET + until you get to the desired speed, then release.You can also use SET + to operate the tap-up function. Press andrelease SET + to increase the vehicle set speed in 1 mph (1.6 km/h)increments. • Use the accelerat...

MEDIA: Press repeatedly to select: • AM, FM1, FM2, or CD • DVD/FES (if equipped) • SAT1, SAT2 or SAT3 (Satellite radio mode if equipped). • LINE IN (Auxiliary input jack) Navigation system hands freecontrol features (if equipped) Press and hold control briefly until the voice icon appears on the nav...

Bounce-back: When an obstacle has been detected in the roof opening as the roof is closing, the roof will automatically open and stop at aprescribed position. Bounce-back override: To override bounce-back function, pull and hold the SLIDE switch within two seconds of a bounce-back event. Theclosing ...

HomeLink 姞 Wireless Control System (if equipped) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a convenient way toreplace up to three hand-heldtransmitters with a single built-indevice. This feature will learn theradio frequency codes of mosttransmitters to operate g...

1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink 威 button you wish to program (locatedon your visor) while keeping theindicator light in view. 2. Simultaneously press and holdboth the chosen HomeLink 威 and hand-held transmitter buttons until the HomeLink 威 i...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined inthe Programming section, replace Step 2 with the f...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

To open the liftgate, press thecontrol button located in the top ofthe liftgate pull cup handle tounlatch the liftgate, then pull on theoutside handle to access the cargoarea. • Do not open the liftgate in agarage or other enclosed areawith a low ceiling. If the liftgate isopened, the liftgate could...

To power close the liftgate withthe rear cargo area controlbutton: Press and release the control on theleft rear quarter panel to close theliftgate. Note: The rear cargo area control button is disabled when the liftgateis latched (fully closed). WARNING: Keep clear of the liftgate when activating th...

• the liftgate is manually closed and left ajar (unlatched) To reset the power liftgate: 1. Disconnect the battery for 20 seconds then, reconnect the battery. 2. Manually close and fully latch the liftgate. 3. Power open the liftgate by using the integrated keyhead transmitter,or the instrument pane...

ROOF RACK SYSTEM (IF EQUIPPED) Loads should never be placed directly on the roof panel. For properfunction of the roof rack system, loads must be placed directly oncrossbars affixed to the roof rack side rails. Your vehicle may beequipped with factory-installed crossbars. Ford Genuine Accessorycross...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and the transmitter portionfunctions as the remote entrytransmitter. Vehicles with a powerliftgate will have a four-button...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Touch and hold the 3 • 4. While holding the 3 • 4 touch the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a ...

Keyless entry keypad autounlock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Touch and hold the 3 • 4. While holding the 3 • 4, touch and release the 7 • 8. While still holding the 3 • 4, touch and release the 7 ...

REMOTE ENTRY SYSTEM The Integrated Keyhead Transmitter (IKT) complies with part 15 of theFCC rules and with RSS-210 of Industry Canada. Operation is subject tothe following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,in...

2. Press and release again within three seconds to unlock all the doors.The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the on position.The battery saver feature will turn off the lamps 10 minutes after ...

Car finder Press twice within three seconds. The horn will chirp and the turn lamps will flash. It is recommended that this method be used to locateyour vehicle, rather than using the panic alarm. Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash f...

Deactivating the memory feature To deactivate this feature: 1. Press and hold either the 1 or 2 control on the driver’s door for fiveseconds. (A tone will be heard after 1 1 ⁄ 2 seconds when the memory store is done) continue to hold until a second tone is heard after five seconds. 2. Within three s...

IKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to reprogram your Integrated Keyhead Transmitters (IKTs) To program a new Integrated Keyhead Transmitter yourself, refer to Programming spare keys in the SecuriLock 威 passive anti-theft sy...

• The battery saver will shut off the headlamps 10 minutes after theignition has been turned to the off position. SECURICODE™ KEYLESS ENTRY SYSTEM The keypad is invisible until touched and then it lights up so you can seeand touch the appropriate buttons. Note: If you enter your entry code too fast ...

5. The doors will lock then unlock to confirm that your personal entrycode has been programmed to the module. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. Erasi...

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the offposition, the indicator will flashonce every two seconds toindicate the SecuriLock 威 system is functioning as a theftdeterrent. • When the ignition is in the on position, the in...

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keepthe ignition in the 3 (on) position for at least three seconds, but no mor...

MyKey™ Restricted Features Standard settings – These settings cannot be changed • The audio system will be muted whenever Belt-Minder 威 is activated until the safety belts are buckled. Refer to the Seating and Safety Restraints chapter for a detailed description of Belt-Minder 威 operation. • Low fue...

Note: The MyKey™ can be cleared within the same key cycle that it was created, otherwise a standard key (Administrator key) is required todisable the MyKey™ programming. To clear all MyKeys™ go to step 2 inthe Disable MyKey™ section. Programming MyKey™ Optional Settings Turn the ignition on using an...

Check MyKey™ System Status The vehicle System Check will provide the status of the followingMyKey™ parameters: • MYKEY MILES — This odometer only tracks mileage when a MyKey™is used. If mileage does not accumulate as expected, then theMyKey™ is not being used by the intended user. The only way tores...

Note: For all vehicles with remote start installed, it is possible to program all ’real’ keys as MyKeys™, in which case, you will need to useyour remote start system to reset all MyKeys™ as Admin keys by doingthe following: 1. Enter the vehicle, close all doors. 2. Remote start the vehicle using you...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help protect your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL Integrated Keyhead Transmitters are brought to the authorized dealer to aid in troubleshooti...

• Press and hold the 7 • 8 and 9 • 0 controls on the keyless entrypad at the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood, and theliftgate is armed individually, and if...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front manual seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Always drive and ride with your seatback upright an...

Using the manual lumbar support (if equipped) The lumbar control is located on theside of the seat cushion. Turn to adjust lumbar support. Rotate the lumbar forward to adjustfirmness. Rotate the lumbar rearward toadjust softness. Folding down the front passenger seatback The front passenger seatback...

Adjusting the front power seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and ...

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the controlto adjust firmness. Press the rearward side of thecontrol to adjust softness. Heated seats (if equipped) WARNING: Persons who are unable to feel pai...

REAR SEATS Head restraints Lift the head restraint so that it is located directly or as close as possiblebehind your head. The head restraints can be movedup by pulling up on the headrestraint. Press the release button to lowerhead restraint. WARNING: The adjustable head restraint is a safety device...

1. Lift the handle located on theside of the seat. The seatback will fold flat. 2. Lift the handle all the way upuntil the seat releases from thefloor. Rotate the seat forward toallow access to the third row. Seating and Safety Restraints 163 2010 Flex (471) Owners Guide, 1st PrintingUSA (fus)

Press the control located at theback of the rear door opening onetime to fold the seat back down andtumble the seat forward for accessto the 3rd row. Exiting the third row seat 1. Stow the head restraint by pressing the head restraint release buttonwhile sliding the head restraint fully down. 2. Pul...

4. To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright position. Note: The seatback will not raise if the rear latch hooks are notproperly engaged to the floorstriker. If the seatba...

Stowing the third row seat 1. Remove all objects from the seatand stowage tub. 2. Stow the head restraints bypressing the head restraint releasebutton while sliding the headrestraints fully down. 3. From the rear of the vehicle, fold seatback by pulling and holding thenumber 1 strap while pushing th...

2. To return the seatback to uprightposition, pull the number 1 strap,then while holding the number 1strap, pull the long strap located onthe seatback to raise the seatback. 3. Pull the head restraints up totheir normal adjusted positions. WARNING: Ensure seat is latched to vehicle floor by pushing/...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System™ totailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower airba...

Safety belt precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while th...

WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and...

WARNING: Failure to inspect and replace if necessary the belt and retractor assembly after an accident could increase the risk of injury in a collision. All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have threetypes...

Front safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,squeeze and hold the buttons on theside and slide t...

WARNING: Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If...

WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s airbagsystem. Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are...

3. Wait 10 seconds after the safety belt warning light turns off. • Step 4 must be completed within 20 seconds after the completion ofStep 3. 4. For the seating position being disabled buckle then unbuckle thesafety belt three times at a moderate speed, ending in the unbuckledstate. • After Step 4, ...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. WARNING: Do not place any object between an occupant and an ai...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the cond...

WARNING: Do not attempt to service, repair, or modify the Safety Canopy 威 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 . See your authorized dealer. WARNING: All occupants of the vehicle including the driver should always wear their safe...

WARNING: If the Safety Canopy 威 system has deployed, the Safety Canopy 威 will not function again unless replaced. The Safety Canopy 威 system (including the A, B, C, and D pillar trim and headliner) must be inspected and serviced by an authorized dealer. Ifthe Safety Canopy 威 is not replaced, it will...

Disposal of airbags and airbag equipped vehicles(including pretensioners) Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for childr...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Combining safety belt and LATCH lower anchors for attachingchild safety seats When used in combination, either the safety belt or the LATCH loweranchors may be attached first, provided a proper installation is achieved.Attach the tether strap afterward, if included with the child seat. Referto Recom...

• 2nd row bench (60/40) • 3rd row Note : The cargo tie-downs at the rear edge of the floor are nottether anchors. 3. Clip the tether strap to theanchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision. 4. Tighten the ...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

Child restraint and safety belt maintenance Inspect the vehicle safety belts and child safety seat systems periodicallyto make sure they work properly and are not damaged. Inspect thevehicle and child seat safety belts to make sure there are no nicks, tearsor cuts. Replace if necessary. All vehicle ...

NOTICE TO CROSSOVER VEHICLE OWNERS Crossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on streets, highwaysand off-road. Crossover vehicles arenot designed for cornering at speedsas high as passenger cars any morethan low-slung sports cars ar...

Note: Your AWD vehicle is not intended for off-road use. The AWD feature gives your vehicle some limited off-road capabilities in whichdriving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other than those condi...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck...

Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by an authorized dealer.Front wheel drive (FWD) vehicles and those with an independent rearsuspension (if equipped) may require alignment of all four wheels. The tires should also be...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tir...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

SNOW TIRES AND CABLES/CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle cont...

• If possible, avoid fully loading your vehicle. • Remove the tire cables when they are no longer needed. Do not usetire cables on dry roads. • The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. • D...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. Tires, Wheels and Loading 244 2010 Flex (471) Owners Guide, 1st PrintingUSA (fus)

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, thenthe load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now yo...

WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle control, vehicle r...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safeif installed properly and adjusted to the manufacturer’s specifications. Thetr...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

All Wheel Drive (AWD) vehicles: Tow your All Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a vehicle transport trailer. Do not tow your All Wheel Drive vehicle with the front wheels offthe ground (by using a tow dolly) and the rear wheels on thegr...

STARTING Positions of the ignition 1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and allelectrical accessories off withoutlocking the steering wheel. To lockthe steering wheel, remove the keythen turn the steering wheel. 2. Accessor...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS is disabled due to a malfunction and needs to be serviced. Even when the ABS is disabled,normal braking is still...

When an event occurs that activates AdvanceTrac 威 with RSC 威 you may experience the following: • A slight deceleration of the vehicle • The “sliding car” indicator light will flash. • If your foot is on the brake pedal, a vibration in the pedal. • If the driving condition is severe and your foot is ...

During Electronic Stability Control events the “sliding car” icon in the instrument cluster will flash. Certain adverse driving maneuvers may activate the Electronic StabilityControl system, which include but are not limited to: • Taking a turn too fast • Maneuvering quickly to avoid an accident, pe...

or the speed of the vehicle and trailer is too high. Pull the vehicle-trailerover to a safe location to check the trailer weight distribution and tongueload and reduce speed to a safe level while towing. If trailer sway isexperienced, SLOW DOWN. Always use caution when towing a trailerand follow the...

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir. If the steering wanders or pulls equipped with either EPS or hydraulicsteering system, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspe...

M (Manual) with Grade Assist Initially, moving the lever to M (Manual) activates grade assist andcancels Overdrive. Grade Assist: • Provides additional grade(engine) braking and extendslower gear operation on uphillclimbs for hilly terrain ormountainous areas. • Provides additional enginebraking thr...

Understanding your SelectShift Automatic™ Transmission (SST) This vehicle is equipped with aSelectShift Automatic™transmission (SST) gearshift lever.SST is an automatic transmissionwith the ability for the driver tochange gears up or down (without aclutch) as desired. By moving thegearshift lever fr...

The message center display in theinstrument cluster will show thecurrent selected gear you are in. In order to prevent the engine fromrunning at too low an RPM, whichmay cause it to stall, the SST willautomatically make some downshifts even if it has determined that youhave not downshifted in time. ...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system,located on the liftgate, provides avideo image, which appears on thenavigation system screen, of thearea behind the vehicle. It addsassistance to the driver whilereversing or reverse parking thevehicle. To use the camera system, place t...

Night time and dark area use At night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is necessary that bothreverse lamps are operating in order to get a clear image in the dark. Ifeither of the lamps are not operating, stop using the cam...

Automatic Search for Parking Space To start, press the APA controlswitch (on the console in front ofthe gearshift). The message centerwill display ACTIVE PARKSEARCHING. To designate whatside of the street to search on, usethe turn signal. The arrow symbols>> and << in the message centeri...

Automatic Steering into Parking Space Automatic steering is activated when you stop the vehicle, remove yourhands from the steering wheel and select the R (Reverse) gear. Be surethe steering wheel motion is not obstructed by any objects. The vehiclewill steer itself from this point on as you follow ...

Troubleshooting Why isn’t APA searching for a parking space? • You may have deactivated the AdvanceTrac 威 system. • One of the doors (except the driver’s door) may not be securelyclosed. Why doesn’t APA offer a particular parking space? • Something may be contacting the front bumper or side sensors....

• One of the parked vehicles has a high altitude attachment (i.e. saltsprayer, snow plow, moving truck high bed, etc.) High altitudeattachments may not be detected by the system. • The parking space length or parked objects position have changedafter the vehicle has passed the parking space. • The t...

Note: The AWD OFF message may also be displayed in the message center if the AWD system has overheated and defaulted to front wheeldrive. This condition may occur if the vehicle was operated in extremeconditions with excessive wheel slip, such as deep sand. To resumenormal AWD function as soon as po...

If the engine, transmission, AWD system components or axles aresubmerged in water, their fluids should be checked and changed, ifnecessary. Driving through deep water may damage the engine ortransmission. If the front or rear axle is submerged in water, the axle lubricant andPTU (Power Transfer Unit...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fuel to theengine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you mayrestart your vehic...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Driver smart window motor 2 15A Trailer tow stop/turn lamps 3 15A Not used (spare) 4 30...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 64 HC micro relay PCM 65 G8VA relay A/C clutch 66 G8VA relay Fuel pump * Cartridge Fuses ** Mini Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steer...

• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driv...

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remov...

1. Block the diagonally oppositewheel. 2. Remove wheel cover (ifequipped) with the lug wrench tipand loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack...

4. Insert the straight end of the jackretention bracket through the eyeletof the angled bracket and swing theretention bracket over the jack. Withthe jack in place, place the loopedend of the retention bracket overthe threaded stud in the trunk floorand secure it with the plastic wingnut. If you are...

• Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle. Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operati...

• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation. What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stageswith the temporary mobility kit: • In the first stage, the tire will be reinfla...

4. Plug the power cable into the 12Vpower point in the vehicle. 5. Remove the warning sticker found on the canister and place it on thetop of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) . 7. Turn dial (1) counterc...

Note: When the sealing compound is first added into the tire, theair pressure gauge reading on the compressor unit may indicate ahigher value; this is normal and should be no reason for concern.The pressure will drop after about 30 seconds of operation. Thetire pressure has to be checked with the co...

3. Turn the dial clockwise to the air position. Turn on the kit by pressingthe on/off button. 4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jam area. Note: The tire pressure has to be checked with the compressor in theOFF position to g...

Removal of the Sealant Canister from the Temporary Mobility Kit 1. Unwrap the clear tube from thecompressor housing. 2. Locate the yellow cap at the endof the clear tube. 3. Using the yellow cap tool, pressthe tab located on the temporarymobility kit compressor housingwhile pulling up on the sealant...

Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorizeddealer for assistance. Be sure to check the sealantcompound’s “use by” date regularly.The “use by” date is on the lowerright hand corner of the labellocated on...

Note: Inspect the wheel pilot hole prior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot sur...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

3.5L V6 EcoBoost engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar R...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft 威 Premium Windshield Washer Concentrate (ZC-32-A), available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade an...

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white cotton cloth. For morethorough cleaning, use a mild soap and wate...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specificat...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

Engine shield Some vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter changes. It is secured withfour screws. WINDSHIELD WASHERFLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the ...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil ...

4. Attach the new wiper to thewiper arm and press it into placeuntil a click is heard. If you find this procedure toodifficult, please see your dealer. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make...

• If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft 威 maintenance-free battery which normally does notrequire additional water during itslife of service. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, k...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interval s...

• Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications and capacities in this chapter. Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems.Th...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reservoir.If you removed the radiator cap in an ...

• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your ve...

and other factors. If this occurs, there is no need to pull off the road.The vehicle can continue to be driven while this message is active. WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full powe...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel conta...

immediately. It may take several driving cycles for the check fuel fill inletlamp or CHECK FUEL FILL INLET message to turn off. A driving cycleconsists of an engine start-up (after four or more hours with the engineoff) followed by city/highway driving. Continuing to drive with the checkfuel fill in...

rating of 91 or higher is recommended. The performance gained by usingpremium fuel will be most noticeable in hot weather or in severe dutyapplications such as towing a trailer. Some stations offer fuels posted as ⬙ Regular ⬙ with an octane rating below 87, particularly in high altitude areas. Fuels...

2. Slowly insert the funnel into theEasy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the funnel. Do not use aftermarket fun...

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still pres...

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to changea number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually gi...

emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability. WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can sta...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage. If necessary, add fluid in 1/2 pint(250 ml) increments through thefiller tube until the level is correct. If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condi...

Changing the air filter element 3.5L V6 3.5L V6 (EcoBoost) 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to r...

6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage tothe eng...

ENGINE DATA Engine 3.5L V6 engine 3.5L V6 EcoBoost engine Cubic inches 214 214 Fuel See Octane recommendations earlier in this chapter. See Octane recommendations earlier in this chapter. Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Spark plug gap 0.052–0.056 inch (1.32–1.42 mm) 0.033–0.037 inch (.838– .939...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code 6F50 6–Speed Automatic Transmission J 6F55 6–Speed Automatic Transmission (withEcoBoost) G Maintenance and...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Locking fuel plug for capless fuel systems Cargo area protector Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehi...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ........................102 Active Park Assist .....................280 AdvanceTrac ..............................262 Air cleaner filter ...............376–378 Air conditioning ..............68, 71, 74 manual heating and airconditioning system .................68 Airbag supplementa...

V Vehicle Identification Number(VIN) ..........................................384 Vehicle loading ..........................242 Ventilating your vehicle ...........258 W Warning lights (see Lights) .......12 Washer fluid ..............................347 Water, Driving through .............291 Wind...