Ford 2010 Edge v.2- Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

may seek to access the information independently of Ford MotorCompany and Ford of Canada. To the extent that any lawpertaining to Event Data Recording applies to SYNC 威 or its features, please note the following: Once 911 Assist (if equipped)is enabled (set ON), 911 Assist may, through any paired an...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Powertrain malfunction/reducedpower: Illuminates when a powertrain or a AWD fault has beendete...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected. Contact yourauthorized dealer as soon aspossible. Normal braking is still functional unless the brake warning lightalso is illuminated. Airbag readiness: If this light fails to illuminate...

Low tire pressure warning (ifequipped): Illuminates when your tire pressure is low. If the lightremains on at start up or whiledriving, the tire pressure should bechecked. Refer to Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

• With message center See TRIP A/B under Message center in this chapter. MINI MESSAGE CENTER (IF EQUIPPED) Selectable features Press and release the TRIP/RESET stem to scroll and reset the followingfunctions. Select or reset the function by holding the TRIP/RESET stemfor more than two seconds. Info ...

1. To disable/enable the reversesensing system feature, select thisfunction using the TRIP/RESETstem or put the vehicle in R(Reverse). 2. Press and hold the TRIP/RESET stem for two seconds to turn the rearpark assist OFF or ON. MESSAGE CENTER (IF EQUIPPED) Your vehicle’s message center is capable of...

(800 km). This value is not the same as the average fuel economydisplay. The running average fuel economy is re-initialized to a factorydefault value if the battery is disconnected. MPG (L/100km) Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km. If you calculat...

System check and vehicle feature customization Press SETUP repeatedly to cyclethe message center through thefollowing features: PRESS RESET FOR SYS CHECK For each of the monitored systems, the message center will indicateeither an OK message or a warning message for two to four seconds. Press RESET ...

AUTOUNLOCK This feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off. Press RESET to turn autounlock on or off. POWER LIFTGATE (if equipped) This feature allows users to open/close the rear liftgate at the touch of abutton...

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For moreinformation on how the system operates under these conditions, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If the warning stays on...

AUDIO SYSTEMSQuick start — How to get going WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The drivers primary responsibility is the s...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

While in folder mode, pressFOLDER to access the next folder on MP3 discs, if available. Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is...

song appears in the display that you would like to delete, press OK.The song will appear in the display for confirmation. Press OK againand the display will read SONG DELETED. If you do not want todelete the currently listed song, press / to select either RETURN or CANCEL. Note: If there are no song...

SEEK, SEEK to fast seek through the previous /next channels. In TEXT MODE, press SEEK, SEEK to view the previous/additional display text. In CATEGORY MODE, press SEEK, SEEK to select a category. Satellite radio is available only with a valid SIRIUS 威 subscription. Check with your authorized dealer f...

In folder mode, press SEEK, SEEK to scroll through tracks within the selected folder.Press FOLDER, FOLDER to access the previous/next folder (if available). Press OK to close and return to the main menu. COMPRESS (Compression): Available only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears ...

14. AM/FM: Press to select AM/FM1/FM2 frequency band. 15. ON/OFF/Volume: Press to turn on/off. Turn to increase/decreasevolume. Note: If the volume is set above a certain level and the ignition isturned off, the volume will come back on at a “nominal” listening levelwhen the ignition switch is turne...

To auto eject up to 6 CDs, press and hold until the system begins ejecting all loaded discs. If the discs are not removed, the system willreload the discs. 19. CD slot: When prompted by the system, insert a CD label side up. Auxiliary input jack (Line in) WARNING: Driving while distracted can result...

USB port (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of thei...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location th...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the distribution of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distribu...

5. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engagesautomatically in MAX A/C, (defrost) and (floor/defrost). 6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Operating tips • To reduce fo...

6. Recirculated air: Press to activate/deactive air recirculation in the vehicle. Recirculated air may reduce the amount of time needed tocool down the interior of the vehicle and may also help reduce undesiredodors from reaching the interior of the vehicle. Recirculation can beengaged manually in a...

• Manual operation: 1. Select or . 2. Select A/C and (recirculated air). Use (recirculated air) with A/C to provide colder airflow. 3. Set the temperature to 60°F (16°C). 4. Set highest fan setting initially, then adjust to maintain comfort. To aid in side window defogging/demisting in cold weather:...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Autolamp control The autolamp system provides lightsensitive automatic on/off control ofthe exterior light...

Fog lamp control (if equipped) The headlamp control also operatesthe fog lamps. The fog lamps can beturned on when the headlamp control is in the , , or positions and the high beams arenot turned on. Pull the headlamp control towardsyou to turn the fog lamps on. Thefog lamp indicator light will illu...

WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may notprovide adequate lighting during these conditions. Failure to activateyour headlamps under these conditions may result i...

• (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp bulb center from theground and mark an 8 foot(2.4 meter) horizontal reference lineon the vertical wall or screen at thisheight (a piece of ma...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument pan...

Map/dome lamp (if equipped) The dome lamp lights when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition isoff. The map lamps are activated by pressing the controls on either sid...

Replacing headlamp bulbs Check the operation of all bulbs frequently. 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Reach over the front bolster. 4. Remove the bulb by turning itcounterclockwise and then pulling itstraight out. 5. Disconnect the electricalconnec...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Normal speed operation of rearwiper. 1 — Intermittent operation of rearwiper. O (off) — Rear wiper and washer off. For rear wash cycle, rotate (and hold as de...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. Slide on rod feature The visor will slide back and forthon the rod for increased sunlightcoverage. Rotate the visor towardsthe side window and extend itrearward for additional sunlightcoverage. Note: To sto...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

To operate one-touch down: • Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press theswitch to any position to stop thewindow operation. If the switch is pressed and held tothe normal close or one-touch up position during a one-touch d...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. Accessory delay With accessory delay, the audio system, power wind...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

SPEED CONTROL With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. Th...

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink 威 buttons be erased for security purposes, refer to Programming in thi...

5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the pres...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

Note: The liftgate movement direction can be reversed with a second press of the instrument panel, or the rear cargo area control button, or asecond double press of the integrated keyhead transmitter button. To manually operate the liftgate: 1. Disable the liftgate power function. Refer to the Messa...

CARGO AREA FEATURES Cargo management system (if equipped) The cargo management systemconsists of storage compartmentslocated in the floor of the rear cargoarea. 1. To open, lift the release handleand the lid. 2. To close, lower the lid. Cargo net (if equipped) The cargo net secures lightweightobject...

Utility hook The utility hook can be used tohang small items such as grocerybags, etc. Do not hang more than10 lb (4.5 kg) on the hook. ROOF RACK SYSTEM (IF EQUIPPED) Loads should never be placed directly on the roof panel. For properfunction of the roof rack system, loads must be placed directly on...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and the transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a ...

WARNING: Make sure all persons are clear of the liftgate area before using power liftgate control. In order to fully lower and latch the liftgate, press the control twice. If the liftgate stops mid travel, it may have detected an obstacle, Checkto ensure the liftgate swing zone is free from obstruct...

2. Press and hold either the 1 or 2control on the driver’s door for fiveseconds. (A tone will be heard after1 1 ⁄ 2 seconds when the memory store is done) continue to hold until asecond tone is heard after fiveseconds. 3. Within three seconds press the control on the Integrated Keyhead Transmitter. ...

3. Insert the new battery. Refer tothe instructions inside the IKT forthe correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery housing cavity. 4. Snap the battery cover back ontothe key. Note: Replacement of the battery will not cause the ...

Illuminated exit • When all vehicle doors are closed and the key is removed from theignition, the interior dome lamps, parking lamps and the puddle lamps(if equipped) will illuminate. The lamps will turn off if all the doors remain closed and • 25 seconds elapse, or • the key is inserted in the igni...

other. The interior lamps will illuminate. Note: If the two-stage unlocking feature is disabled, all doors will unlock; for more information regardingtwo-stage unlocking, refer to the Unlocking the doors/Two stage unlock section earlier in this chapter. To unlock all doors, enter the factory set cod...

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the offposition, the indicator will flashonce every two seconds toindicate the SecuriLock 威 system is functioning as a theftdeterrent. • When the ignition is in the on position, the in...

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keepthe ignition in the 3 (on) position for at least three seconds, but no mor...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Using the manual lumbar support (if equipped) The lumbar control is located on theside of the seat cushion. Rachet the lever up or down toadjust lumbar support. Adjusting the front manua...

Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation. Pull lever up to adjust seatback. Folding down the front passenger seatback (if equipped) The front passenger seatback can be folded to a horizontal position tomake room for a long load. To fold...

WARNING: Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting during sudden stops. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seat...

WARNING: To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat. Donot place objects underneath the front passenger seat or between theseat and the center console (if equipp...

• To program position 2, repeat the previous procedure using controlbutton 2. • A chime will sound confirming that a memory position has been set. A position can be recalled: • in any gearshift position if the ignition is not on. • only in P (Park) or N (Neutral) if the ignition is on. A memory seat...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. The heated seats will only function when the ignition is in the onposition. To operate the heated seats: • Press the contro...

Press the release button to lowerthe head restraint. Folding down the 60/40 rear seats Note : The head restraints should be placed in the full down position before folding the seatback down. Note : Ensure that no objects such as books, purses, or briefcases are on the floor in front of, on or under ...

Adjusting the second row seatback WARNING: Reclining the seatback can cause an occupant to slide under the seat’ssafety belt, resulting in severepersonal injuries in the event of acollision. The second row seat reclines foradditional comfort. To adjust thesecond row seatback to the desiredposition, ...

To access the cup holders, lift upone of the slotted areas on thecover. WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. Returning the 2nd row armrest to the upright position Close the cover on the cup holders. Rotate the armrest rearward untilthe armrest is ...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the...

during frontal collisions, and in rollover and side collisions when theSafety Canopy 威 is activated. This helps increase the effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can beactivated alone or, if the collision is of sufficient severity, together withthe ...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, press the releasebutton and remove the tong...

All safety restraints in the vehicle are combination lap and shoulderbelts. The driver safety belt has the first two types of locking modes andthe front outboard passenger and rear seat safety belts have three typesof locking modes described as follows: Vehicle sensitive mode This is the normal retr...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. When to use the automatic locking mode In this mode, the shoulder be...

The safety belt pretensioner tightens the safety belts firmly against theoccupant’s body at the start of the crash. WARNING: The driver and front passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results ...

To adjust the comfort guide: 1. Slip the shoulder belt into thebelt guide. 2. Slide the guide up or down alongthe webbing so that the belt iscentered on the occupant’s shoulder. WARNING: Position the safety belt comfort guide so that the belt rests across the middle of your shoulder. Failure to adju...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s airbagsystem. One-time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safet...

1. Turn the ignition switch to the on position. DO NOT START THEENGINE. 2. Wait until the safety belt warning light turns off (approximately1–2 minutes). • Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, buckle then...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belt...

system. The person in the front passenger seat may appear heavier orlighter due to the conditions described in the list above. WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front pa...

WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the cond...

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-fro...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with the syst...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddler seat). Small...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

anchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH attachments cannot be installed at the center seating position.LATCH compatible child seats (with attachments on belt webbing) canonly be used at this seating position provided that the child seatmanufacturer’s instructions...

3. Clip the tether strap to theanchor as shown. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of acollision. 4. Tighten the child safety seattether strap according to the manufacturer’s instructions. WARNING: If the safety seat is...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO CROSSOVER VEHICLE OWNERS Crossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on streets, highwaysand off-road. Crossover vehicles arenot designed for cornering at speedsas high as passenger cars any morethan low-slung sports cars ar...

driving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other than those conditions could subject the vehicle to excessivestress which might result in damage which is not covered under yourwarranty. For AWD vehicl...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalprob...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The Tire Pressure Monitoring System is NOT a substitute for manually checking tire pressure. The ...

When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to identify an issue to remind youthat the damaged road wheel/tire needs to be repaired and put back onyour vehicle. To restore the full functionality o...

Low Tire Pres-sure WarningLight Possiblecause Customer Action Required Flashing WarningLight Spare tirein use Your temporary spare tire is in use. Re-pair the damaged road wheel and re-mount it on the vehicle to restore systemfunctionality. For a description of howthe system functions under these co...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all pa...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, thenthe load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now yo...

Do not exceed the maximum loads listed on the Safety ComplianceCertification label. For load specification terms found on the label, referto Vehicle loading–with and without a trailer in this chapter. Remember to figure in the tongue load of your loaded vehicle whenfiguring the total weight. FWD GCW...

Preparing to tow Use the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. Contact your authorized dealer or areliable trailer dealer as soon as possible if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to ...

cause them not to function properly. Your lamp outage featuremay also be disabled or provide incorrect information. Trailer tow connector(equipped on vehicles with a Class II trailer tow/prep package) The trailer tow connector is located under the rear bumper, on thedriver’s side of the vehicle. Ref...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • If you are driving down a long or steep hill, shift to a lower gear...

All Wheel Drive (AWD) vehicles: Tow your All Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a vehicle transport trailer. Do not tow your All Wheel Drive vehicle with the front wheels offthe ground (by using a tow dolly) and the rear wheels on thegr...

STARTING Positions of the ignition 1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and allelectrical accessories off withoutlocking the steering wheel. To lockthe steering wheel, remove the keythen turn the steering wheel. 2. Accessor...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

or avoiding objects in the roadway. ESC operates by applying brakes toone or more of the wheels individually and, if necessary, reducing enginepower if the system detects that the vehicle is about to skid or slidelaterally. During ESC events the “sliding car” icon in the instrument cluster will flas...

STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until itstops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level(below the MIN mark on the reservoir)...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

• Allows the transmission to select gears that will provide the desiredengine braking based on the vehicle inputs mentioned above. This willincrease engine RPM during engine braking. Overdrive Cancel with Grade Assist is designed to provide optimal gearselection in hilly terrain or mountainous areas...

BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have anintegrated convex spotter mirrorbuilt into the upper outboard cornerof the outside mirrors. They aredesigned to assist the driver byincreasing visibility along the side ofthe vehicle. For more information onyour side view mirrors, refer to E...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. With the AWD option, power will be delivered to the frontwheels and distributed to the rear wheels as needed. The AWD system isactive all the time and requires no input from the oper...

be required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through high water, drive slowly. Traction or brakecapability may be limited. When driving through water, determine the depth; avoid water higherthan t...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

After an accident, if the engine cranks but does not start, this switchmay have been activated. This switch is located behind apanel on the left side of the cargoarea. To reset the switch: 1. Turn the ignition to off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch b...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 38 20A Subwoofer/amplifier 39 20A Radio 40 20A Not used (spare) 41 15A Automatic dimming rear viewmirror 42 10A Not used (spare) 43 10A Rear wiper logic 44 10A Customer accessory feed 45 5A Front wiper logic 46 7.5A Occupant classification senso...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: If your vehicle is equipped with the tire pressure monitoring system (TPMS), th...

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one...

Tire change procedure WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the t...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) ...

2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper c...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Avoid cleaners or polishes that increase the gloss of the upper portionof the instrument panel. The dull finish in this area helps protect thedriver from undesirable windshield reflection. • Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s seatbelts, as these actions may weaken the belt webbing. LEATHER SEA...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the secondary hood latchthat is located under the frontcenter of the hood. 3. Lift the hood and support it with th...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer flu...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil ...

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not ...

4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil it stops. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level dipstick and/or the engine oil filler cap removed. Engine oil and filte...

It is recommended you use the appropriate Motorcraft 威 oil filter or another with equivalent performance for your engine application. BATTERY Your vehicle is equipped with aMotorcraft 威 maintenance-free battery which normally does notrequire additional water during itslife of service. If your batter...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quar...

• NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection cha...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certainconditions. Care should be taken to avoid inhaling excess fumes. WARNING: The flow of fuel through a fuel pump no...

WARNING: If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result inpersonal injury. Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% etha...

Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. If the problemspersist, see your authorized dealer.Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermark...

possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1,000 miles(1,600 km) of driving (engine break-in period). You will get a moreaccurate measurement after 2,000 miles...

3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Divide total miles traveled...

• Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended...

properly (bulb is burned out), or if the OBD-II system has determinedthat some of the emission control systems have not been properlychecked. In this case, the vehicle is considered not ready for I/M testing. If the service engine soon indicator is on or the bulb does not work, the vehicle may need ...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels...

Changing the air filter element 1. Release the clamps that securethe air filter housing cover. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter elementfrom the air filter housing. 4. Wipe the air filter housing andcover clean to remove any dirt ordebris and to ...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................79 AdvanceTrac ..............................219 Air cleaner filter ...............305–307 Air conditioning ..........................58 Airbag supplemental restraintsystem ................145–146, 154, 157 and child safety seats ............147description...

Passenger OccupantClassification Sensor .................133 Power distribution box(see Fuses) ...............................245 Power door locks ......................103 Power liftgate ..............................96 Power mirrors .............................80 Power point ........................