Ford 2009 F-150 v.3- Manuals

Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning andlubrication materials are significantsteps towards this aim. Information in this respect is highlighted in thisguide with the tree symbol. CALIFORN...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide/Customer Information Guide that is provided to you along with your Owner’s Guide. Special instructions For you...

Event Data Recording Other modules in your vehicle — event data recorders — arecapable of collecting and storing data during a crash or nearcrash event. The recorded information may assist in theinvestigation of such an event. The modules may recordinformation about both the vehicle and the occupant...

Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance PreparationPackage. Notice to owners of pickup trucks and utility type vehicles WARNING: Utility vehicles have a significantly higher rollover rate than other types of veh...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of their vehicle. Only use cel...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster Platinum instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

On vehicles equipped with a message center, “ENGINE FAILSAFEMODE” will be displayed, refer to Message center in the Driver Controls chapter. Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on position...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be checked. Referto Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will illuminate for...

Four wheel drive low (RTT) (ifequipped): Displays when four-wheel drive low is engaged. Ifthe light fails to display when theignition is turned on, or remains on, have the system servicedimmediately by your authorized dealer. Four wheel drive high (RTT) (ifequipped): Displays when four-wheel drive h...

Tachometer (if equipped): Indicates the engine speed inrevolutions per minute. Driving withyour tachometer pointercontinuously at the top of the scalemay damage the engine. Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H...

Yellow area (warning) — the transmission fluid is higher thannormal operating temperature. Thiscan be caused by special operationconditions (i.e. snowplowing, towingor off road use). Refer to Special Operating Conditions in the scheduled maintenanceinformation for instructions. Operating the transmi...

AUDIO SYSTEMS AM/FM stereo system (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is ...

To activate the autoset feature: Press MENU repeatedly until AUTO PRESET ON/OFF appears in the display. Use SEEK to toggle AUTO PRESET to ON, and either wait five seconds for the search toinitiate or press OK to immediately initiate the search. If you pressanother control within those five seconds, ...

do not choose a slot within five seconds, the system will choose for you.Once loaded, the first track will begin to play. To auto load up to six discs– Press and hold LOAD until the display reads AUTOLOAD #. Load the desired disc, label side up. The systemwill prompt you to load discs for the remain...

TEXT: In MP3 mode only– Press TEXT repeatedly to view Album (AL), Folder (FL), Song (SO) and Artist (AR) in the display, if available. In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT and thenpress SEEK to view the add...

MEMORY PRESETS (0–9): There are 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memory presets, tune to the desired channelthen press and hold a memory preset number (0–9) until sound returns. TEXT: Press and release to display the artist and song title. While...

titles, the display will read REPLACE SONG? Press OK to access thesaved titles and press to cycle through the saved titles. When the song title appears in the display that you would like to replace,press OK. SONG REPLACED will appear in the display. b. DELETE A SONG: Press OK to delete a song from t...

c. UNLOCK ALL CHANNELS: Press OK when UNLOCK ALL CHANNELS is displayed and the display will read ENTER PIN. Enteryour four-digit PIN and the system will unlock all channels and thedisplay will read CHANNEL UNLOCKED. d. RESET PIN: Press OK when RESET PIN is displayed. The display will read ARE YOUR S...

To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off. 3. Attach one end of the audio extension cable to the headp...

location, such as the center console or the glove box, when the vehicle isin motion. The audio extension cable must be long enough to allow theportable music player to be safely stored while the vehicle is in motion. USB port (if equipped) WARNING: Driving while distracted can result in loss of vehi...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. You are in a location that i...

SINGLE ZONE CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fogand thin ice. The system will automatically provide outside air to reducewindow fogging. Press this button again to return to the prev...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter. 1. + Fan speed control: Press to increase the fan speed. 2. Defrost: Distributes outside air through the wi...

4. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. A/Cengages automatically in MAX A/C, (defrost) and (floor/defrost). 5. AUTO: Press to engage automatic temperature control. Select the desired temperature using the tempera...

12. – Front fan speed control: Press to decrease the fan speed. 13. A. R Rear defroster (if equipped): Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this chapter for more information. If your vehicle is equipped with both reardefroster and heated mir...

3. Manual override control: Allows you to manually select where airflow is directed. To return to full automatic control, press AUTO.When choosing to control airflow manually, press repeatedly to togglethrough the settings to choose: • : Distributes air through the windshield defroster vents, de-mis...

9. PASS TEMP: Press to engage/disengage separate passenger side temperature control. Turn to increase/decrease the air temperature onthe passenger side of the vehicle. The recommended initial setting isbetween 72°F (22°C) and 75°F (24°C), then adjust for comfort. Thepassenger side temperature settin...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH HEATEDAND COOLED SEATS (NAVIGATION BASED–IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter. 1. CLIMATE: Press to control the climate control system through the touch displ...

TOUCHSCREEN FUNCTIONS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter. Temperature: Press the up and down arrows on the left side of the screen to increase/decrease the airflow temperature for the driver side ofthe vehicle. Thi...

VOICE COMMANDS IN CLIMATE MODE Please refer to the Voice commands in climate mode section of the Navigation supplement for more information on using voice commands with the climate control system. Operating tips • To reduce fog build up on the windshield during humid weather,select (defrost). Temper...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position to turn on the parking lamps. Rotateclockwise to the secondposition to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights nor...

At this point, the headlamps and park lamps will turn off. Fog lamp control (if equipped) The headlamp control also operatesthe fog lamps. The fog lamps can beturned on only when the headlamp control is in the , or position and the high beams are notturned on. Pull headlamp control towards youto tur...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from thecenter...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument pan...

Rear dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on. • any of the remote entry controlsare pressed and the ignition is off. The reading portion, the two outer lights, can only be tur...

Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position and openthe hood. 2. Remove the pushpin that holdsthe air deflector/protective coverfrom the upper inboard corner ofthe lamp. 3. Loosen the...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Rain sensing wipers (if equipped): The rain sensing wipers will automatically activate when moisture is present on the windshie...

motor to burn out. Before operating the wiper on a dry windshield,always use the windshield washer. In freezing weather, be sure the wiperblades are not frozen to the windshield before operating the wipers. TILT STEERING WHEEL (IF EQUIPPED) 1. Pull and hold the steering wheelrelease control toward y...

Memory feature The steering column positions are saved when doing a memory setfunction and can be recalled along with the vehicle personality featureswhen a memory position is selected through the remote entrytransmitter, keyless entry keypad or memory switch on the side of thedriver’s seat (if equi...

WARNING: Do not leave children unattended in the vehicle and do not let children play with the power sliding back window. They may seriously injure themselves. Accessory delay (if equipped) With accessory delay, the window switches may be used for up to10 minutes after the ignition switch is turned ...

With microphone The mirrors will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up. Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorperformance. Do not c...

Heated outside mirrors (if equipped) Heated mirrors remove ice, mist andfog. To activate the heated mirrors,press the rear defrost button R located on the climate control panel. Refer to Rear window defroster in the Climate Controls chapter for more information. On vehicles not equipped with rear de...

Telescoping trailer tow mirrors (if equipped) The telescoping feature allows themirror to extend approximately3.5 inches (90 mm). This feature isespecially useful to the driver whentowing a trailer. Pull the mirrorsinward carefully when drivingthrough a narrow space. POWER ADJUSTABLE FOOT PEDALS (IF...

Automatic power deploy: • The running boards will extenddown and out when the doors areopened. Automatic power stow: • The running boards will return tothe stowed position when thedoors are closed. There will be atwo second delay before therunning boards move in to thestowed position. Manual power d...

Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board under body mounts to liftthe vehicle when jacking. Please utilize proper jacking points. Refer to Changing the tires in the Roadside Emergencies chapter. WARNING: In extreme climates, exc...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or theclutch pedal (if equipped). Thiswill not erase your vehicle’spreviously set speed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedco...

In any mode: • Press VOL + or VOL - to adjustthe volume. SYNC 威 system hands free control features Press briefly to use the voice command feature. You will hear atone and LISTENING will appear inthe radio display. Press andhold to exit voice command. Press to activate phone mode or answer a phone ca...

For further information on the Navigation system/SYNC 威 system, refer to the Navigation and SYNC 威 supplements. MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console. WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may...

The moon roof has a built-in sliding shade that can be manually openedor closed when the glass panel is shut. To close the shade, pull it towardthe front of the vehicle. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a ...

1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink 威 button you wish to program (locatedon your visor) while keeping theindicator light in view. 2. Simultaneously press and holdboth the chosen HomeLink 威 and hand-held transmitter buttons until the HomeLink 威 i...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined inthe Programming section, replace Step 2 with the f...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

• Differences in the automatic shut-off points on the fuel pumps atservice stations • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed controlsystem engaged to ...

TRAIN RIGHT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN RIGHT REAR TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Whee...

TRAIN LEFT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN RIGHT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Whee...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. Tailgate removal Your tailgate is removable to allow more room for loading....

Cross bars: Aluminum cross bars with T-slot channels in all four sides, and a latch mechanism that allows the end supports to snap over theexisting cleats. Cross bars are rated to hold loads up to 100 lb (45 kg)load evenly distributed between the two crossbars, and the T-slots aresized to accept ind...

Bed divider: This panel will keep small items up to 400 lb (180 kg) in position in the pickup box. Also includes T-slots to allow attachment ofindustry-standard roof rack accessories. • To remove bed divider, lift handle on each side and lift end supportshroud off of the cleat. • To install bed divi...

Side mounted tool bins: Watertight bins can be positioned at any point along the side rails and can be easily removed (even when full), andcarried to wherever the contents are needed. Each bin will hold up to60 lb (27 kg) of cargo, and has a drain plug for use as a cooler. Note: When multiple bins a...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to the SecuriLock™ passive anti-theft system section in this chapter for more i...

Autolock The autolock feature is available on vehicles with power locking. Thisfeature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shift into any gear putting the vehicle in motion, (for manualtransmission the park brake should not be engaged...

6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was deactivated or twice (one short and one longchirp) if autolock was activated. 7. Turn the ignition to the off position. The horn will chirp once toconfirm the procedure is complete. Keyless entry keypad...

Message center procedure For information on activating/deactivating the autounlock feature usingthe vehicle’s message center, refer to Message center information in the Driver Controls chapter. CHILDPROOF DOOR LOCKS (ON VEHICLES WITH REAR DOORS) • When these locks are set, therear doors cannot be op...

• structures around the vehicle, or • other vehicles parked next to your vehicle. Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors withouta key. • lock all the vehicle doors withouta key. • activate the personal alarm. If there are problems with the...

Activating the two-button memory switch (if equipped) To activate this feature: 1. Position the seat, power mirrors, adjustable pedals and steeringcolumn (if equipped) to the desired positions. 2. Press and hold either the 1 or 2control on the driver’s seat for fiveseconds. (A tone will be heard aft...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 10 minutes after thelast door is closed, even if the dimmer control is on. Perimeter lighting feature (if equipped) The perimeter ligh...

Conversely, a horn chirp followed by a honk will indicate the system isenabled. Pressing the power door control two times again will turn the feature on if it was previously off, or off if it was previously on.Every two consecutive presses of the power door control after successfully entering the co...

started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare keys to you...

Automatic arming The vehicle is armed immediately after switching the ignition to the offposition. Automatic disarming Switching the ignition to the on position with a coded key disarms the vehicle. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key,you will need ...

4. After three seconds but within 10 seconds of turning the ignition tothe 1 (off) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keepthe ignition in the 3 (on) position for at least three seconds, but no mor...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Front seat • Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place. 2009 F-150 (f12) Owners Guide (own2002) , 3rd Printing USA (fu...

• To gain access to the storagecompartment (if equipped) inyour armrest, lift the latch toopen the lid. Using the manual lumbar support For more lumbar support, turn thelumbar support control toward thefront of vehicle. For less lumbar support, turn thelumbar support control toward therear of vehicl...

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the controlfor additional support. Press the rear side of the control toreduce support. Adjusting the front power seat (if equipped) WARNING: Never adjust the ...

The control is located on the outboard side of the seat cushion. Move the switch in the direction ofthe arrows to raise or lower thefront portion of the seat cushion. Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the switch in the directio...

To remove an air filter: 1. Remove key from ignition. 2. Push up on the outside rigid edgeof the filter and rotate toward thefront of the vehicle once tabs arereleased. 3. Remove filter. To install a filter: • First, position the filter in it’shousing making sure that the farforward end is all the w...

To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as poss...

1. Pull control on the side of the seat to release seat cushion fromstorage position. 2. Push seat cushion down until it locks into horizontal position. Folding up the rear seats (CrewCab vehicles only) The rear seat has a split 60/40 cushion. Each seat cushion can be flippedup into a vertical stora...

Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit in a rear seating position where they can be properly restrained. WARNING: Never let a passenger hold a...

WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a childanywhere near them. WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts fo...

While you are fastened in the safety belt, the combination lap/shoulderbelt with a cinch tongue adjusts to your movement. However, if youbrake hard, turn hard, or if your vehicle receives an impact of 5 mph(8 km/h) or more, the safety belt will become locked and help reduceyour forward movement. Lap...

Shorten and fasten the belt whennot in use. For long term storage, the lap belt can be placed into a pocket found onthe inside lid of the storage compartment. To store the lap belt, do thefollowing: 1. Open the storage compartmentlid. 2. Place the lap belt into the pocketfound on the inside lid of t...

An energy management retractor is a device which pays out webbing in acontrolled manner. This feature is designed to help further reduce therisk of force-related injuries to the occupant. Safety belt systems equipped with an energy management retractor mustbe replaced if they were in use during a fr...

WARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which does not have this feature) must be checked by an authorized dealer toverify that the automatic locking retractor feature for child seats is stillfunctioning properly. In additio...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

WARNING: While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belted and surviving an accident. We recommend youleave the Belt-Minder 威 system activated for yourself and others who may use the vehicle. To reduce the risk of in...

WARNING: Do not use extensions to change the fit of the shoulder belt across the torso. AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system is designed to work inconjunction with the safety belts to help protect the driver and frontoutboard passenger from certain uppe...

Personal Safety System has determined the occupant conditions andcrash severity are appropriate to activate these devices. Refer to the Personal Safety System™ section in this chapter. WARNING: The front passenger airbag is not designed to offer protection to an occupant in the center front seating ...

If two adults and a child occupy a Regular Cab , properly restrain the child in the center front unless doing so would interfere with driving thevehicle. This arrangement provides lap and shoulder belt protection forall occupants, and airbag protection for the adults. All occupants of thevehicle sho...

internal injuries, particularly to occupants who are not properlyrestrained or are otherwise out of position at the time of airbagdeployment. Thus, it is extremely important that occupants be properlyrestrained as far away from the airbag cover as possible whilemaintaining vehicle control. WARNING: ...

detect the presence of a properly seated occupant and determine if thefront passenger’s frontal airbag should be enabled (may inflate) ordisabled (will not inflate). The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if: • the front passenger seat ...

WARNING: An out of position front center occupant could affect the decision of the front passenger sensing system. If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the Cust...

WARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not rep...

How does the Safety Canopy 姞 system work? The design and development of theSafety Canopy 威 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot function properly in the event of a collision. S.O.S. Post Crash Alert The S.O.S Post Crash Alert automatically flashes the turn signal lampsand sounds t...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsand toptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybel...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioning bo...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced652 mm (25.7 inches) apart. The standardized spacing for LATCH loweranchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH ...

point called the top tether anchor. Tether straps are available as anaccessory for many older safety seats. Contact the manufacturer of yourchild seat for information about ordering a tether strap, or to obtain alonger tether strap if the tether strap on your safety seat does not reachthe appropriat...

Front seat tether strap attachment 1. Route the child safety seat tether strap over the back of the seat andunder the head restraint. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, otherwise routethe tether strap ove...

Rear seat tether strap attachment There are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow) in the SuperCab andSuperCrew. These loops are to beused as both routing loops andanchor loops for up to three childsafety seat tether straps. Forexample, th...

3. Tighten the tether strapaccording to the child seatmanufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child beinginjured in a collision greatly increases. Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back be...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The ...

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired. At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflatea...

When weather temperature changes occur, tire inflation pressures alsochange. A 10°F (6°C) temperature drop can cause a corresponding dropof 1 psi (7 kPa) in inflation pressure. Check your tire pressuresfrequently and adjust them to the proper pressure which can be foundon the Safety Compliance Certi...

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls forcracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your Owne...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Warning Lamp will turn ON if the tire pressure is significantly low.Once the light is illuminated, ...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the following chartfor information conc...

Low TirePressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is inuse. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a description ofhow the system functions underthese condition...

TPMS reset procedure (if applicable) The TPMS reset tool is ONLY provided for vehicles with differentfront and rear tire pressures. The TPMS reset procedure needs tobe performed after tire rotation only on these vehicles. WARNING: To determine if your vehicle has different recommended pressures for ...

2. Press and release the brakepedal. 3. Cycle the ignition from off to onthree (3) times ending in the onposition— DO NOT start the engine. 4. Press and hold the brake pedalfor two (2) seconds, then release. 2009 F-150 (f12) Owners Guide (own2002) , 3rd Printing USA (fus) Tires, Wheels and Loading 2...

10. Perform Steps 8 and 9 on the right front tire, right rear tire andfinally the left rear tire. Training is complete after the horn sounds forthe last tire trained (left rear tire) and the message center displays: TRAINING COMPLETE . Turn the ignition to off. If two short horn beeps are heard, the...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. GCW (Gross Combined Weight) – is the...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fo...

SuperCrew 4x4 (157” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3V 3.55 13500 (6123) 7600 (3448) 3.73 15100 (6849) 9200 (4173) 5.4L 3.31 14000 (6350) 8100 (3674) 3.55 15500 (7031) 9600 (4354) 3.73 15500 (7031) 17100 (7756)* 9600 (4354) 11100 (5035)* *...

2. Measure the height of a reference point on the front and rear bumpersat the center of the vehicle. 3. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within 1 ⁄ 2 inch (13 mm) of the reference point. After proper adjustment, the rear bumper shou...

WARNING: The Ford TBC has only been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and not hydraulic surge or electric-over-hydraulictypes. It is the responsibility of the customer to ensure that the trailerbrakes are adjusted appropriately, function...

3. GAIN setting display: Shows the current GAIN setting. This will illuminate when a trailer is connected, flash if the trailer becomesdisconnected, or remain off if no trailer is connected. 4. +/– (GAIN adjustment buttons): Pressing these buttons will adjust the TBC’s power output to the trailer br...

Note: Your TBC can be diagnosed by your authorized dealer to determine exactly which trailer fault has occurred; however, if the faultis with the trailer this diagnosis is not covered under your Ford warranty. Points to Remember: • Remember to adjust gain setting before using the TBC for the firstti...

If it is necessary to relocate the trailer hitch ball position, aframe-mounted trailer hitch must be installed. Driving while you tow When towing a trailer: • To ensure proper “break-in” of powertrain components, do not trailertow during the first 1,000 miles (1,600 km) of a new vehicle. • To ensure...

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maintenance and Specifications chapter for the lubricant specification. Rememb...

STARTING Positions of the ignition 1. Off — locks the automatictransmission gearshift lever andallows key removal. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. Accessory — allows the electricalaccessories such as the radio to...

4. Make sure the parking brake isset. 5. Turn the key to 3 (on) withoutturning the key to 4 (start). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to ...

3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the key to the off position, wait 10 seconds and try Step 2 again. If the engine still fails tostart, press the accelerator to the floor ...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. WARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating infor...

Prior to using the engine block heater, follow these recommendations forproper and safe operation: • For your safety, use an outdoor extension cord that is productcertified by Underwriter’s Laboratory (UL) or Canadian StandardsAssociation (CSA). Use only an extension cord that can be usedoutdoors, i...

Depending on the type of factory installed equipment, your engine blockheater system may consume anywhere between 400 watts or 1000 wattsof power per hour. Your factory installed block heater system does nothave a thermostat; however, maximum temperature is attained afterapproximately three hours of...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

WARNING: Trailer sway control does not prevent a trailer from swaying, it mitigates the sway from increasing once it has occurred. If you are experiencing trailer sway it is likely that the traileris improperly loaded for the correct tongue weight or the speed of thevehicle and trailer is too high. ...

PREPARING TO DRIVE WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased gro...

Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Pa...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system,located on the tailgate, provides avideo image, which appears in therearview mirror or the navigationsystem (if equipped), of the areabehind the vehicle. It addsassistance to the driver whilereversing or reverse parking thevehicle. To u...

Note: The default setting for the rear camera delay is off. Press the “Settings” button found on the navigation screen (if equipped) to set therear camera delay feature to on or off. When towing, the camera system will only see what is being towedbehind the vehicle; this might not provide adequate c...

The message center will display 4X4 SHIFT IN PROGRESS during the shift. The message center will then display the system mode selected. If any of the above shift conditions are not met, the shift will not occurand the message center will display information guiding the driverthrough the proper shifti...

Activating the electronic locking differential (ELD) The ELD can be turned on bypulling the knob on the 4WD controltoward you while the control is ineither 4H (4X4 High) or 4L (4X4Low) mode. Once the knob is pulled, thelight located on the control willblink for approximately two secondsand then it w...

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps. You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and braking control of your vehicle, you must have all fourwheels ...

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through highwa...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, sli...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow canbe found in the Ford Truck Body Builders Layout Book, Snowplowsection, found at www.fleet.ford.com/truckbbas. A typical installationaffects the following: • Certification to government safety laws such ...

The attached snowplow blade restricts airflow to the radiator, and maycause the engine to run at a higher temperature. Attention to enginetemperature is especially important when outside temperatures areabove freezing. Angle the blade to maximize airflow to the radiator andmonitor engine temperature...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

Should your vehicle shut off after a collision due to this feature, you mayrestart your vehicle by doing the following: 1. Turn the ignition switch to the off position. 2. Turn the ignition switch to the on position. In some instances the vehicle may not restart the first time you try torestart and ...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pink Pink 40A — — Orange Green Green 50A — — Red Red Red 60A — — Blue Yellow Yellow 70A — — Tan — Bro...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Moon roof 2 15A Not used (spare) 3 15A Not used (spare) 4 30A Not used (spare) 5 10A Keypad illumination, Brake ShiftInterlock (BSI), SJBmicroprocessor power 6 20A Turn signals, Stop lamps 7 10A Low beam hea...

Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. To restore the full functionalityof the monitoring system, all road wheels equipped with tire pressuremonitoring sensors must be mounted on the vehicle. Have a flat serviced by an authoriz...

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

To remove the jack on SuperCrew models: 1. Lift both rear seat cushions. 2. Remove the insert containing the Easy Fuel ™ funnel from the driver’sside. 3. Remove the two small wing nuts on the passenger side.4. Slide the plastic box toward the driver’s side and remove. Removing the spare tire 1. Use ...

• Front Note: Use the frame rail as the jacking location point, NOT the control arm. • Rear WARNING: To lessen the risk of personal injury, do not put any part of your bodyunder the vehicle while changing atire. Do not start the engine whenyour vehicle is on the jack. Thejack is only meant for chang...

3. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases significantly and the spare tire carrier ratchets or slips whenthe tire is raised to the maximum tightness. Tighten to the best of yourability, to the ...

Note: Inspect the wheel pilot hole prior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot sur...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of th...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. Ford recommends your vehicle be towed with a wheel lift or flatbed. Donot tow with a slingbelt. Ford Motor C...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emi...

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, LimitedService Publications CHQ202The Canadian RoadP.O. Box 2000Oakville, ON, CanadaL6J 5E4 REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your v...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Pr...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

5.4L ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). •...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Apply Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11-A) [InCanada use Motorcraft Multi-Purpose Cleaner (...

• For routine cleaning, wipe the surface with a soft, damp cloth. Formore thorough cleaning, wipe the surface with a mild soap and watersolution. In Canada, use Motorcraft Vinyl Cleaner (CXC-93). Dry thearea with a soft cloth. • If the leather cannot be completely cleaned using a mild soap andwater ...

• Do not spill coffee, ketchup, mustard, orange juice or oil-basedproducts on the leather as they may permanently stain the leather. • Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl or plastics. Scratches Natural Markings - Because the leath...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that islocated on the front bumper under the grill. 3. Lift the hood until the lift cylinders hold it open. 2009 F-15...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 1. Windshield washer fluid reservoir 2. Transmission fluid dipstick (4.6L 2V only) 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil ...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insertthe dipstick fully, then remove itagain. • If the oil level is between the lower and upper holes orbetween the MIN and MAXmarks (depending onapplication), the oil level is acceptable. DO NOT ADD OIL. • If ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling ...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interval s...

• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter. Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, ...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

WARNING: Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures,damage may occur and your warranty may be invalidated. WARNING: When refueling always shut the engine off and...

Easy Fuel™ “no cap” fuel system Your fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel filler door and insert thefuel filler nozzle into the fuel system. The Easy Fuel™ system isself-sealing and protected against dust, dirt, water and snow/i...

Flex Fuel Vehicle (FFV) fuel fill inlet Flex fuel vehicles have a yellow bezel placed over the fuel fill inlet. Choosing the right fuel If your vehicle is a flexible fuel vehicle (FFV), use only UNLEADEDFUEL and FUEL ETHANOL (Ed75–Ed85). If your vehicle is not a flexible fuel vehicle (FFV), then onl...

Octane recommendations Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily under mostdriving conditions while you areusing fuel with the recommendedoctane rating, see your authorized dealer to prevent any engine damage. Unleaded Gasoline Engines Your vehicle is d...

FFV engine Flex fuel vehicles have a yellow bezel around the fuel fill inlet. It is best not to alternate repeatedly between gasoline and E85. If you doswitch fuels, it is recommended that you add as much fuel aspossible—at least half a tank. Do not add less than five gallons (18.9L)when refueling. ...

WARNING: Do not try to pry open or push open the Easy Fuel™ system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others. When filling the vehicle’s fuel tank from a portable fuel container, use thefunnel included with the vehicle. 1. Locate the white...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect the emission controlequipment on your vehicle. Failure to pass this inspection could preventyou from getting a vehicle registration. Your vehicle ma...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

Checking 6-speed automatic transmission fluid The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does notconsume fluid. However, the fluid level should be chec...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/or...

8. Replace the air filter housingcover and secure the clamps. Becareful not to crimp the filterelement edges between the air filterhousing and cover and ensure thatthe tabs on the edge are properlyaligned into the slots. 9. Slip the air tube onto the air filterhousing and tighten the air-tubeclamp b...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................74 AdvanceTrac ..............................274 Air cleaner filter ...............389, 392 Air conditioning ........41, 44, 46, 49 manual heating and airconditioning system .................41 Airbag supplemental restraintsystem ........................18...

fail-safe cooling .......................369idle speed control ...................363lubrication specifications .......393refill capacities ........................393service points ..................357–358 Engine block heater .................270 Engine oil ..................................360 ch...

V Vehicle Identification Number(VIN) ..........................................399 Vehicle loading ..........................244 Ventilating your vehicle ...........270 W Warning lights (see Lights) .......12 Washer fluid ..............................359 Water, Driving through .............308 Wind...