Ford 2008 F-550 v.3- Manuals

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

if the modification is removed. When a dealer or repair facility works onyour vehicle, it may be necessary for them to access the information inthe Powertrain Control System. This information will likely identify if anyunauthorized modifications have been made to the system and may beused to determi...

If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theSafety Compliance CertificationLabel. The label is located on thedriver’s side door pillar or on therear edge of the driver’s door. Youcan determine whether theambulance manufacturer followedFord’s reco...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Vehicles equipped with a manual transmission Vehicles equipped with an automatic transmission 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt)USA (fus) Instrument Cluster 12

Harley-Davidson vehicles Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make s...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily ...

Four wheel drive low (ifequipped): Illuminates when four-wheel drive low is engaged. Four wheel drive high (ifequipped): Illuminates when four-wheel drive high is engaged. Anti-theft: Flashes when the SecuriLock™ Passive Anti-TheftSystem has been activated. Speed control (if equipped): Illuminates w...

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley-Davidson instrumentcluster 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt)USA (fus) Instrument Cluster 19

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engine and let the eng...

Standard instrument cluster Harley-Davidson instrumentcluster Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls below thenormal range, stop the vehicle, turnoff the engine and check the engineoil lev...

Battery voltage gauge (manualtransmission only): Indicates the battery voltage when the ignition isin the RUN position. If the pointermoves and stays outside the normaloperating range, have the vehicle’selectrical system checked as soon aspossible. Transmission fluid temperature gauge(automatic tran...

AUDIO SYSTEMSAM/FM stereo system (if equipped) Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe ope...

current track is finished playing. CD SHUF will appear in the display. Todisengage, press SHUFFLE again. SHUFFLE OFF will appear in thedisplay. Note: In CD/MP3 mode, press SHUFFLE to play the tracks in random order. In MP3 folder mode, the system will randomly play all trackswithin the current folde...

The default setting is off; increasing your vehicle speed will not change the volume level. Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly withvehicle speed to compensate for road and wind noise. Recommended...

12. Memory presets: To set a station: Select frequency bandAM/FM1/FM2; tune to a station,press and hold a preset control until sound returns. You may store up tosix stations in each frequency band for a total of 18. In satellite radio mode (if equipped) , there are 18 available presets, six each for...

turned off, the volume will come back on at a “nominal” listening levelwhen the ignition switch is turned back on. 16. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already loadedinto the system, CD/MP3 play willbegin where it ended last. 17. LOAD: To load a disc into the system, press LOAD. Select...

Auxiliary input jack (if equipped) Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack, located on theinstrument panel below the powerpoint, provides a way to connectyour portable music player to thein-vehicle audio system. This allowsthe audio from a portable mus...

compatible with the AIJ. The AIJ will only work correctly with devicesthat have a headphone output with a volume control. 2. Do not set the portable music player’s volume level higher than isnecessary to match the volume of the CD or FM radio in your audiosystem as this will cause distortion and wil...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe oper...

DVD player controls 1. Headphone control A/B: Press to select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for that headset. When aheadphone channel has been selected (A or B), selections will affect thesource on that channel only. Note: Headphone A can acces...

press the 2 and 4 memory preset buttons on the audio system at thesame time to perform the same function. For further interactioninformation, refer to Single Play/Dual play. 12. MEDIA: Press repeatedly to select from the various possibleplaying media sources (AM, FM1,FM2, SAT (if equipped), CD, DVD,...

1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controlsdecrease and increase the display brightness. 3. DISPLAY: Press to access the ...

23. ILLUMINATION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit. Since all batterieshave a limited shelf life, replace them when the unit fails to control theDVD player. Remove the screw and unlatch t...

Headphones Wireless headphones Your FES system is equipped withtwo sets of battery powered,infrared wireless headphones. TwoAAA batteries are needed to operatethe headphones. (Batteries areincluded.) Additional infrared wirelessheadphones may be purchased foruse with the system. Also, wiredheadphone...

Wired headphones Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. You may purchase wired headphones for your FES ...

FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only. The radio will ignore button presses that affect the primary(speaker) audio source. LOCKED (disabled): The FES buttons are ...

use this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting/streaming via internet, intranets and/or other networks or inother electronic content distribution systems, such as pay-audio oraudio-on-demand appli...

Be sure to review User Manuals for video games and video gameequipment when used as auxiliary inputs for your Family EntertainmentSystem (FES). Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where they wi...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with theair flow selector in the O (OFF) position. • Do not put objects under the front seats that will interfere...

• DATC with heated seats and heated mirrors Temperature conversion: To switch between Fahrenheit and Celsius, refer to Units (English/Metric) under either Standard Message Center or Optional Message Center in the Driver Controls chapter In order to achieve maximum cooling performance, press , A/C, ,...

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. • To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out”. For maximum cooling performance (MAX A/C): Automatic operation: 1. Pre...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged. Always remember to turn on your headlamps at dusk ...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableilluminated switches in the vehicleduring headlamp and parklampoperation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Note: If the battery is disconnected, discharg...

5. Locate the vertical adjuster (2)for each headlamp. Adjust the aimby turning the adjuster controleither clockwise (to adjust up) orcounterclockwise (to adjust down). 6. In addition to the horizontal linemarked in step 2, a pair of verticallines (5) must be marked at thecenter line of the headlamps...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. MAP LAMPS (IF EQUIPPED) The dome lamp turns on when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry con...

Replacing exterior bulbs Replacing headlamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position and openthe hood. 2. Remove the four bolts from thetop, side and bottom front of theheadlamp assembly. 3. Pull the assembly straight outdisengaging two snap clips tofender. 4...

Replacing brake/tail/turn/back-up lamp bulbs - Pick-ups only 1. Make sure the headlamp switch isin the OFF position and then openthe tailgate to expose the lampassemblies. 2. Remove the two bolts from thetail lamp assembly and carefully pullthe lamp assembly from the tailgatepillar by releasing the ...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL (IF EQUIPPED) 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering up or downuntil you find the desired location. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. Never adjust the steering column when the v...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. If your vehicle is equipped with a moon roof, referto One-touch moonroof later in ...

The auxiliary power point is locatedon the instrument panel. On SuperCab and Crew Cab models, another power point is located on the rear of the center console (if equipped). Do not use the power point for operating the cigarette lighter element (ifequipped). To prevent the fuse from being blown, do ...

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (t...

Power rear slider window (if equipped) Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not...

The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) (when the mirror is on) to ensure abright clear view when backing up. Do not block the sensors on the front and back of the inside rearview mirror since this may impair proper mirror performance.Do ...

the full travel may cause the system to disable the fold/unfold function toprotect the motors from overheating. Should this occur, waitapproximately 3 1 ⁄ 2 minutes for the system to reset and function to return to normal. Note: The powerfold mirrors are designed to operate while the vehicle is stat...

travel is reached, it is normal to hear the power telescoping motorsrunning as long as you continue to hold the switch. • To telescope the mirrors inboard, press and hold the right side of thepower telescope switch until the mirrors reach their desired position. Memory mirrors (if equipped) This sys...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control toadjust accelerator and brake pedaltoward you or away from you. The adjustment allows fo...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previouslyset speed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased...

The relays are coded as shown inthe accompanying illustration. There will also be one power leadfor each switch found as a blunt-cutand sealed wire located below theinstrument panel and to the left ofthe steering column. They are coded as follows: Switch Circuit number Wire color Fuse AUX 1 CAC05 Ye...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a convenient way toreplace up to three hand-heldtransmitters with a single built-indevice. This feature will learn theradio frequency codes of mosttransmitters to operate g...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined inthe “Programming” section, replace Step 2 with the...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

• Rear cupholders (Crew Cab only) Use only soft cups in the cupholder. Hard objects can injure youin a collision. STANDARD MESSAGE CENTER With the ignition in the RUNposition, the message center,located on your instrument cluster,displays text messages that alertyou to possible problems ormalfunctio...

OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the RUNposition, the message center,located on your instrument cluster,displays important vehicleinformation through a constant monitor of vehicle systems. You may select display features on themessage center for a display ofstatus. The syst...

shutdown when the vehicle speed is below 3 mph (5 km/h). Stop the vehicle as soon as safely possible and contact your authorized dealer. Depending on the severity of the over-temperature condition, the vehiclemay or may not restart after cycling the ignition OFF. If the vehiclerestarts, there may be...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. Tailgate removal Your tailgate is removable to allow more room for loading....

3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels. 5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged in...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.If your vehicle is equipped with the SecuriLock™ Passive Anti-theftsystem, your keys are coded to your vehicle; using a non-coded key willnot permit you...

6. To enable/disable the autolock feature, press the unlock control, thenpress the lock control. The horn will chirp once if autolock wasdeactivated or twice (one short and one long chirp) if autolock wasactivated. 7. Turn the ignition to the 1 (OFF/LOCK) position. The horn will chirponce to confirm...

• unlock the vehicle doors withouta key. • lock all the vehicle doors withouta key. • activate the personal alarm. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Two...

2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will flash once more. If any of the doors are not properly closed the horn will make two quickchirps and the parklamps...

Deactivating the memory seat feature To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2. Within five seconds, press any control on the remote transmitterwhich you would like to deactivate and then press the SET control onthe lower-center portion of the instrument pane...

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmittershould operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammedbecau...

6. Turn the ignition to the 1 (OFF/LOCK) position after you havefinished programming all of the remote entry transmitters. Note: After 20 seconds, you will automatically exit the programming mode. Thedoors will lock, then unlock, to confirm that the programming mode hasbeen exited. Perimeter lamps i...

KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entrykeypad to lock or unlock the doorswithout using a key. The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’s wallet card in the glove box, ismarked on the computer module, and is available...

3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. Your personal code is now erased and only the factory set 5–digit codewill work. Anti-scan feature If an incorrect code has been entered 7 times (35 consecutive buttonpresses), the keypad will go...

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the samekey chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded key while starting the engine. Theseobjects will not cause dama...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints (if e...

Captain’s chair (if equipped) • Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace. • To recline the seatback, pull therelease lever handle located onthe side of the seat up. • Push down the lever (ifequipped) located at the bottomof the seatback to quick...

Press front to raise or lower thefront portion of the seat cushion. Press rear to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Using the manual lumbar support The lumbar support control islocated on the outboard side of theseat ...

A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remoteentry transmitter UNLOCK control (if the transmitter is programmed toa memory position) or, when you enter a valid personal entry code thatis programmed to a memory position. To pro...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull onthe seatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a ...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag supplemental restraint system (S...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, push the releasebutton and remove the tongu...

This mode should be used any time a child safety seat is installed except a booster in a front or rear outboard passenger seating position(if equipped). Children 12 years old and under should be properlyrestrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety ...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checkedaccording to the procedures in the Workshop Manual . Failure to replace the belt and retractor assembly could increase the...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. To adjust the shoulder belt height,push the button and slide t...

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around thehips, not across the waist. • 1st row center seating position on SuperCab and Crew Cab The lap belt does not adjust automatically. Insert the tongue into the correctbuckle (the buckle closest to thedirec...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The Belt-Minder 威 feature will not activate. The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are...

Reasons given... Consider... “The people I’m with don’twear belts” Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. “I have an airbag” Airbags offer greater protection whenused with safety belts. F...

• the driver’s safety belt is unbuckled • the parklamps/headlamps are in the OFF position (If the vehicle isequipped with Autolamps, this will not affect the procedure) While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belt...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch(20 cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your authorized dealer. Use only extensions manufactured by the same supplier as the s...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of th...

Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly one or ...

An infant in a rear-facing seat faces a high risk of serious or fatalinjuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passengerairbag is turned off. See Passenger airbag ON/OFF switch. How does the airbag supplemental restrain...

restrained or are otherwise out of position at the time of airbagdeployment. Thus, it is extremely important that occupants be properlyrestrained as far away from the airbag module as possible whilemaintaining vehicle control. Several air bag system components get hot after inflation. Do nottouch th...

Disposal of airbags and airbag equipped vehicles See your local authorized dealer. Airbags MUST BE disposed of byqualified personnel. Passenger airbag ON/OFF switch (if equipped) An airbag ON/OFF switch(if equipped) may be installed in this vehicle. Beforedriving, always look at the face of the swit...

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can constantly monitor the child’s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician:...

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a sp...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

When children should use booster seats Children need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the vehicle seat andlap/shoulder belt to fit properly. Generally this is when they weigh about80 lb. (36 kg) (about 8 to 12 years old). Booster seats sho...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Either type can be used at any seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 k...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

• F-Series Crew Cab Tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. 4. You may need to pull the seatback forward to access the tethera...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information on shiftingprocedures and maintenance can befound in your Owner’s Guide . You should become thoroughly familiarwith this information befor...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Maximum Permissible Inflation Pressure is the tire manufacturer’s maximum permissible pressure and/or the pressure at which themaximum load can be carried by the tire. This pressure is normallyhigher than the manufacturer’s recommended cold inflation pressurewhich can be found on the Safety Complian...

Matching Spare Tire/Wheel Information sections for descriptions): Store and maintain at the higher of the front and rear inflation pressureas shown on the or Safety Compliance Certification Label or the TireLabel. 6. Visually inspect the tires to make sure there are no nails or otherobjects embedded...

Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that may be wedged in thetread grooves. Check for holes or cuts that may permit air leak...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) U.S. and Canada Federal regulations require tire manufacturers to placestandardized information on the sidewall of all tires. This informationidentifies and describes the fundamental characteristics of the tire andalso provides a U.S. DOT Tire Identification...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess ...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. The Tire Pressure Monitoring System is NOT a substitute formanually checking tire pressure. The tire press...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

TPMS reset tool A special TPMS reset tool has been provided with your vehicle to resetyour TPMS after tire rotation. The tool is located with your Owner’sGuide materials. Please take the tool with theprovided Velcro 威 strip on the back and mount it in the bottom rightcorner of your Owner’s Guide cas...

3. Press and hold the brake pedal for two (2) seconds, then release. 4. Turn the ignition to OFF/LOCK ( DO NOT remove the key.) 5. Cycle the ignition from OFF/LOCK to RUN three (3) times ending inRUN. DO NOT start the engine. If reset mode has been entered successfully, the horn will sound once,the ...

Rotation, pressure adjustment and TPMS reset example The following example describes all the major steps involved in rotatingtires on a vehicle with different front and rear tire pressures. Itillustrates that the TPMS reset procedure needs to follow tire rotationand pressure adjustment to avoid a po...

Rotation, pressure adjustmentand successful completion of theTPMS reset procedure Sensor 1: 80 psi Sensor 2: 80 psi Sensor 3: 50 psi Sensor 4: 50 psi Tire rotation and air pressureadjustment followed by sensorresetting will ensure the system is properly programmed for vehicleswith different front an...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label (vehicles exported outside the U.S. and Canada maynot have a Tire Label) on the B-Pillar or the edge of the driver’s door.Look for “THE COMBINED W...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Tongue Load or Fifth Wheel King Pin Weight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer, multiply 5,000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 lb.(227 to 340 kg). For an 11,5...

Loaded vehicles may handle differently than unloaded vehicles.Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle can haul more cargo and people than most passenger cars.Depending upon the type and placement of...

Note: Do not exceed the GCWR listed for your vehicle on the following chart/table, or the GVWR, GAWR or tire ratings specified on the TireLabel or Safety Compliance Certification Label. Towing trailers beyond the maximum recommended trailerweight which exceeds the limit of the vehicle’s GCWR, GVWR, ...

Maximum GCWR - lb. (kg.) Engine Rear axle ratio Manual transmission Automatic transmission F–350 Dual Rear Wheel (DRW) Chassis Cab 5.4L 3.73 15000 (6804) 16500 (7484) 4.10 17500 (7938) 18500 (8391) 6.8L 4.10 20500 (9299) 21500 (9752) 4.30 22500 (10206) 23000 (10433) F–450 Chassis Cab/F–550 6.8L 4.88...

Hitch Type Maximum Gross Trailer Weight — lb. (kg) Maximum Tongue Weight — lb. (kg) 6.8L DRWPickup2.5” ID withoutadapter(requires2.5” drawbar) Weight carrying 8000 (3629) 800 (363) Weightdistributing 15000 (6804) 1500 (680) 6.8L DRWPickup2.5” ID withadapter(requires2” drawbar) Weight carrying 6000 (...

Note: Adjusting a weight distributing hitch so the rear bumper of the vehicle is higher than it was unloaded will defeat the function of theweight distributing hitch and may cause unpredictable handling. Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the ve...

The TBC user interface consists ofthe following: 1. +/- (GAIN adjustment buttons): Pressing these buttons will adjust the TBC’s power outputto the trailer brakes (in 0.5increments). The GAIN setting canbe increased to a maximum of 10.0or decreased to a minimum of 0 (notrailer braking). Pressing andh...

the Center High-Mount Stop Lamp (presuming proper trailer electricalconnection). Pressing the vehicle brake pedal will also illuminate bothtrailer and vehicle brake lamps. GAIN: The GAIN setting is used to set the TBC for the specific towingcondition and should be changed as towing conditions change...

TRAILER DISCONNECTED (if equipped with message center) orCHECK TRAILER (if equipped with mini message center): This message is displayed when a trailer connection was determined and thena disconnection, either intentionally or unintentionally, has been sensedduring a given ignition cycle. It is also...

• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lockup.Therefore, if these systems are not functioning properly the TBC maynot function at full performance. • When the vehicle is turned off, the TBC Output is disabled and the...

• Do not exceed the GCWR rating or transmission damage may occur. • Your vehicle may be equipped with a temporary or conventional sparetire. If the spare tire is different in size (diameter and/or width), treadtype (All-Season or All-Terrain) or is from a different manufacturerother than the road ti...

• Trailer loads should be evenly distributed front to back and left toright. • The load distribution within the trailer should be such that 10%–15%of the trailer weight is on the hitch. (15%–25% for fifth-wheel orgooseneck towing.) • Never exceed truck, trailer, receiver, ball, tongue, tire or coupl...

Exceeding these limits may allow water to enter critical vehiclecomponents, adversely affecting driveability, emissions and reliability. Replace front and rear axle lubricants any time the axles have beensubmerged in water. Axle lubricant quantities are not to be checkedunless a leak is suspected. R...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3...

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. Ifthe engine idle speed does not slow down automatically, have ...

If your vehicle has an automatic transmission, it will have a computer assisted cranking system. This feature assists in starting theengine. If the ignition key is turned to the 4 (START) position, and thenreleased when the engine begins cranking, the engine may continuecranking for up to 10 seconds...

outdoors, in cold temperatures, and is clearly marked ⬙ Suitable for Use with Outdoor Appliances. ⬙ Never use an indoor extension cord outdoors; it could result in an electric shock or fire hazard. • Use a 16 gauge outdoor extension cord, minimum. • Use as short an extension cord as possible. • Do n...

Make sure system is unplugged and properly stowed before driving thevehicle. While not in use, make sure the protective cover seals theprongs of the engine block heater cord plug. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, ...

effectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainfull steering control during hard braking and on slippery surfaces.However, the ABS does not decrease stopping distance. Parking brake To set the parking brake, pr...

The Traction Control™ switch,located on the instrument panel tothe left of the climate controlsystem, has an indicator light thatilluminates when the system is off.The Traction Control™ system willautomatically turn on every time theignition is turned off and on. TheTraction Control™ system should n...

• improper steering alignment If any steering components are serviced or replaced, install newfasteners (many are coated with thread adhesive or have prevailingtorque features which may not be re-used). Never re-use a bolt or nut.Torque fasteners to specifications in Workshop Manual . A high crown i...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before s...

When you shut-off and restart the engine, the transmission willautomatically return to normal D (Overdrive) mode (Tow/Haul OFF). Do not use the Tow/Haul feature when driving in icy or slipperyconditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing aroun...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then pu...

Shift according to the following shift speed charts: Upshifts when accelerating (recommended for best fuel economy) 6-speed transmission Shift from: Transfer case position 1 (if equipped) 2H or 4H 4L LO-1 5 mph (8 km/h) 2 mph (3 km/h) 1-2 14 mph (23 km/h) 6 mph (10 km/h) 2-3 22 mph (35 km/h) 9 mph (...

3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when ...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. REVERSE CAMERA SYSTEM (IF EQUIPPED) The reverse camera system, locatedon the tailgate, provides a videoimage (which app...

• auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired. • automatic operation of thehub locks is recommended, and will increase fuel economy • For proper operation, makesure that each hub is fullyengaged and that both hublocks are set to the sam...

4H (4x4 High) – For winter and off-road conditions. Sends power to front and rear wheels. This mode is not intended for use on dry pavement.N (Neutral) – Only used when towing the vehicle. 4L (4x4 Low) – For low-speed off-road applications that require extra power such as steep grades, deep sand or ...

Shifting from 4H (4x4 High) to 4L (4x4 Low) 1. Bring the vehicle to a stop or a speed below 5 mph (8 km/h). 2. Place the gearshift lever in N (Neutral). If the vehicle is equipped witha manual transmission, also depress the clutch pedal. 3. Move the transfer case shift leverthrough N (Neutral) direc...

This position should only be usedwhen towing the vehicle. Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the Electronic Shift On the Fly (ESOF) 4x4 system(if equipped)...

• Do not shift into 4x4 HIGH with the rear wheels slipping. Shifting from 4x4 HIGH to 2WD Rotate the 4x4 control to 2WD atany forward speed. Disengagementof the transfer case and front hubsmay be delayed due to torque bindwhich is caused by driving on dryhard surfaces or performing tightturns while ...

3. Move the 4x4 control to the 4x4HIGH or 2WD position. 4. Hold the shift conditions until the4x4 LOW indicator light shuts off. 5. If the 4x4 LOW indicator light does not shut off within 15 seconds, allow the vehicle to moveat a speed below 5 mph (8 km/h),then repeat steps 2 through 5 whilethe vehi...

Basic operating principles • Do not use 4WD on dry, hard surfaced roads. Doing so will produceexcessive noise, increase tire wear and may damage drive components.4WD modes are only intended for consistently slippery or loosesurfaces. • Drive slower in strong crosswinds which can affect the normal st...

Do not rock the vehicle for more than a few minutes or damageto the transmission and tires may occur or the engine mayoverheat. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Refer to Transmission fluid temperature gauge in the Instrument Clus...

Note: If air is released from your tires, the Tire Pressure Monitoring System (TPMS) indicator light may illuminate (if equipped). Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterh...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, sli...

VEHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate utility equipment. Examples include awheel-lift for tow trucks, cranes, tools for construction or tire service,and pumping fluids. PTO applications draw...

SNOWPLOWING Ford recommends that the Super Duty F-Series used for snow removalinclude a snow plow package option. Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow canbe found in the Ford Truck Body Builders Layout Book, Snowplow section, found at www.fle...

• Snowplowing with vehicles equipped with a diesel engine may result inengine overheating in highway driving with snowplow blade raisedunless equipped with the special engine cooling fan clutch that isincluded with a snow plow package option. Operating the vehicle with the snowplow attached Do not u...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card a...

HAZARD FLASHER The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the flasher...

The switch has a red button on topof it. To reset the switch: 1. Turn the ignition off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the resetbutton. 4. Turn the ignition on. 5. Wait a few seconds and return the key to off. 6. Make another check ...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Not used (spare) 2 15A Not used (spare) 3 15A Family Entertainment System (FES) 4 30A Not used (spare) 5 10A Keypad illumination, Brake-ShiftInterlock (BSI), SPBJB 6 20A Turn signal...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 73 2A** Reverse Camera System (RCS) 74 20A** Gasoline engines: VPWR: HEGO, CMS, MAFS, EVMV,CMCV, VCT, IMTV Diesel engine: VPWR: Engine loads 75 5A** Back-up relay coil power 76 20A** Gasoline engines: VPWR: PCM Diesel engine: VPW...

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the d...

T-type/Mini-spare tire information (Harley-Davidson only) Your vehicle may be equipped with a temporary spare tire. This sparetire is considered “temporary”. Replace the temporary spare with a tireof the same size, speed rating, and load carrying capacity as the otherroad tires as soon as possible. ...

Park on a level surface, activatehazard flashers and set the parkingbrake. • Automatic transmission: Placegearshift lever in P (Park). • Manual transmission: Placegearshift lever in R (Reverse). • Electronic Shift-On-the-Fly(ESOF) 4x4: Place transfer casein 4x4 HIGH or 4x4 LOW beforeturning off the ...

• one handle extension and twotypical extensions. To assemble,align button with hole and slideparts together. To disconnect,depress button and pull apart. • one wheel nut wrench. Slide oversquare end of jack handle. • Vehicles equipped with dualrear wheels, insert the lug wrench extension into the l...

5. Remove the retainer through the center of the wheel. Tire change procedure 1. Turn engine off and block thewheel that is diagonally opposite ofthe flat tire using the wheel chock,if equipped. If the vehicle is a 4x4, lock the manual hub on the wheel. 2. Remove the jack, jack handle, lug wrench an...

13. Insert the jack handle into thepump linkage. 14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed the jack’s rated capacity. 15. Remove the lug nuts with the...

10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier. Note: Do not stow the Harley-Davidson flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 20. Stow the jack, jac...

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot surface (1...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheelson the ground and the rear wheels ...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paintfinish. In ...

• 5.4L V8 gasoline engine • 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use...

• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the ca...

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the airbag system. If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid ...

(ZC-53-A), Motorcraft Paint Sealant (ZC-45), or Motorcraft Custom ClearCoat Polish (ZC-8-A). Note: Removal of deep scuffs and scratches shouldbe performed by an authorized dealer or an experienced repair facility. Low gloss paint area The low gloss area of the instrument panel’s upper dash should be...

• To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLeather Care Kit (ZC-11–D), available from your authorized dealer. • Do not use household cleaning products, a...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl or plastics. Scratches Natural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suchas small scars. These marki...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your authorized dealer has many quality products available to clean yourvehicle and protect its finishes. These quality products have beenspecifically engineered to fulfill your automotive needs; they are customdesigned to complement the style and appearan...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your authorized dealer canprov...

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, p...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. Windshield washer fluid reservoir 2. Battery 3. Transmission fluid dipstick (automati...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield waterrepellant-type fluid or bug wash asthis ...

Note: Poor wiper quality can be improved by cleaning the wiper blades and the windshield; refer to Windows and wiper blades in the Cleaning chapter. Note: To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. Thelayer ...

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “COLD FILL RANGE” in thecoolant reservoir. • Refer to the scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing...

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “COLD FILL RANGE” on the reservoir. 6. R...

Severe climates If you drive in extremely cold climates (less than –34°F [–36°C ]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection cha...

Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to aservice facility as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to the scheduled maintenance information for the appropriate intervals...

Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefill...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The vehicle warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If ...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding one gallon of fuel is enough ...

• Use the same filling rate setting (low-medium-high) each time thetank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and hav...

POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance information for the service interval schedules. If adding fluid is necessary, use only MERCON 威 ATF. • Gasoline engine shown; dieselengine similar. Refer to Identifying components in theengine compartment in the ...

BRAKE FLUID • Vacuum boost system • Hydroboost system The fluid level will drop slowly as the brakes wear, and will rise when thebrake components are replaced. Fluid levels between the “MIN” and“MAX” lines are within the normal operating range; there is no need toadd fluid. If the fluid levels are o...

Carefully read cautionary information on product label. ForMEDICAL EMERGENCY INFORMATION, contact a physician or Poison Control Center immediately; on Ford-Motorcraft products call:1-800-959-3673 (FORD). Failure to follow these instructions may resultin personal injury. During normal operation, the ...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick handle and also in the Maintenance Product Specifications and Capacities section in this chapter. Use of a non-approved automatic tra...

Use only fluid that meets Ford specifications. Refer to Maintenance Product Specifications and Capacities in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE If the original universal joints are replaced with universal joints equippedwith grease fittings, lubrication will be necessary. Refer to...

2. Release three retainer clamps. 3. Pull air filter cover toward passenger side of vehicle and up to releasethe tabs. Lift air filter element up and out of housing. The air filter box needs to be free of any debris before installing a newair filter. 4. Install a new air filter element into the tray...

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on t...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada authorizeddealer. These quality accessories have been specifically engineered tofulfill your automotive needs; they are custom des...

A Accessory delay ........................105 Air cleaner filter ...............375, 377 Air conditioning ..........................81 Airbag supplemental restraintsystem ........................................181 and child safety seats ............182description ..............................181di...