Ford 2008 F-150 v.1- Manuals

Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g.collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emerg...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type,failur...

Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, your vehicle may be equipped withfeatures and options that are different from the ones that are describedin this Owner’s Guide. A market unique supplement may be supplied that complements this boo...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster Base with Tachometer instrument cluster 2008 F-150 (f12) Owners Guide (post-2002-fmt)USA (fus) Instrument Cluster 12

Harley-Davidson instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Electronic throttle control(if equipped): Illuminates when the engine has defaulted to a ⬙ limp-home ⬙ ...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by yourauthorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this light fails t...

Overdrive off (if equipped): Illuminates when the overdrivefunction of the transmission hasbeen turned off, refer to the Driving chapter. If the light does not illuminate, have the transmission serviced soon, or damage may occur. Traction Control™(if equipped): Illuminates when the Traction Control™...

MINI MESSAGE CENTER WARNING DISPLAYS (IF EQUIPPED) Door ajar: Displays when the ignition is in the ON position andany door is open. Low fuel: Displays when the fuel level in the fuel tank is at or nearempty (refer to Fuel gauge in this chapter). Check fuel cap: Displays when the fuel cap may not be ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, theengine is overheating. Stop thevehicle as soon ...

Battery voltage gauge: Indicates the battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal operating range, have thevehicle’s electrical system checkedby your authorized dealer as soon aspossible. Engine oil pressure gauge: Indicates engine oil press...

AUDIO SYSTEMS Quick start — How to get going Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe opera...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

• DELETE SONG: Press OK to delete a song from the system’s memory. Press / to cycle through the saved songs. When the song appears in the display that you would like to delete, press OK.The song will appear in the display for confirmation. Press OK againand the display will read SONG DELETED. If you...

14. AM/FM: Press AM/FM to select AM/FM1/FM2 frequency band. 15. ON/OFF/Volume: Press VOL-PUSH to turn ON/OFF. TurnVOL-PUSH to increase/decreasevolume. Note: If the volume is set above a certain level and the ignition is turned off, the volume will come back onat a “nominal” listening level when the ...

Use / / SEEK, SEEK to toggle ON/OFF. When COMPRESS is ON, the system will bring soft and loud CD passages together for amore consistent listening level. Single Play/Dual Play: If Single Play is ON, press / for Dual Play. FES (FULL/LOCKED): Your vehicle is equipped with a Family Entertaiment DVD syst...

6. OK:(Play/Pause): This control is operational in CD andDVD mode (if equipped). When aCD or DVD is playing in the FES system, press this control to play orpause the current CD/DVD. The CD/DVD status will display in the radiodisplay. OK: Use in various menu selections. If your vehicle is equipped wi...

In satellite radio mode (if equipped) , there are 18 available presets, six each for SAT1, SAT2 and SAT3. To save satellite channels in yourmemory presets, tune to the desired channel then press and hold apreset control until sound returns. Satellite radio is available only with a valid SIRIUS radio...

17. LOAD: To load a disc into the system, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, label side up.If you do not choose a slot within 5 seconds, the system will choose foryou. Once loaded, the first track will begin to play. To aut...

Auxiliary input jack (Line in — if equipped) Your vehicle may be equipped with an Auxiliary Input Jack (AIJ), locatedin the instrument panel tray. The Auxiliary Input Jack provides a way toconnect your portable music player to the in-vehicle audio system. Thisallows the audio from a portable music p...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors:...

CD units are designed to play commercially pressed 4.75 in (12 cm)audio compact discs only. Due to technical incompatibility, certainrecordable and re-recordable compact discs may not functioncorrectly when used in Ford CD players. Do not use any irregular shapedCDs or discs with a scratchprotection...

• MP3 folder mode represents a folder structure consisting of one levelof folders. The CD player numbers all MP3 tracks on the disc (notedby the .mp3 file extension) and all folders containing MP3 files, fromF001 (folder) T001 (track) to F253 T255. • Creating discs with only one level of folders wil...

roof of your vehicle. The vehicle roof provides the best location for anunobstructed, open view of the sky, a requirement of a satellite radiosystem. Like AM/FM, there are several factors that can affect satelliteradio reception performance: • Antenna obstructions: For optimal reception performance,...

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and play a variety of standard video game systems. TheDVD player is capable of playing standard DVDs, CDs, MP3s and iscompatible with CD-R/W, CD-R and cer...

1. Connect the wired headphones in to the headphone jacks on eitherside of the DVD system. Each side is labeled A or B. Headphones plugged into jack A will listen to Channel A and headphones plugged intojack B will listen to Channel B. 2. Adjust the volume levels usingthe volume controls on the DVDs...

select from Angle, Aspect Ratio, Language, Subtitles, Disc resume,Compression, Restore Defaults and Back. For more detailed information,refer to Menu mode. 15. ENTER: Press to select/confirm the current selection. 16. Cursor /Brightness controls: Use the cursor controls to makevarious selections whe...

1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controlsdecrease and increase the display brightness. 3. DISPLAY: Press to access the ...

Battery replacement Batteries are supplied with the remote control unit. Since all batterieshave a limited shelf life, replace them when the unit fails to control theDVD player. Remove the screw and unlatch the battery cover to access the batteries. The remote control unit uses two AAA batteries whi...

Headphones Wireless headphones Your FES system is equipped withtwo sets of battery powered,infrared wireless headphones. TwoAAA batteries are needed to operatethe headphones. (Batteries areincluded.) Additional infrared wirelessheadphones may be purchased foruse with the system. Also, wiredheadphone...

Wired headphones Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. You may purchase wired headphones for your FES ...

The three states are described as: FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only. The radio will ignore button presses that affect the primary(speaker) audio source. LOCK...

use this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting/streaming via internet, intranets and/or other networks or inother electronic content distribution systems, such as pay-audio oraudio-on-demand appli...

Be sure to review User Manuals for video games and video game equipmentwhen used as auxiliary inputs for your Family Entertainment System (FES). Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where they w...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. Do not place objects on top of the instrument panel as theseobjects...

3. A. R Rear defroster (if equipped): Press to defrost the rear window. Refer to Rear window defroster later in this chapter for more information. 3. B. Heated mirrors (if equipped): Press to activate/deactivate. This function will clear snow, fog and thin ice from the side rear view mirrors. 4. Rec...

AUTOMATIC TEMPERATURE CONTROL (ATC) SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to Setup menu in the Message center section of the Driver Controls chapter for more information. If your vehicle is ...

1. Defrost : Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog andthin ice. 2. Fan speed control: Press to manually increase or decrease the fan speed. To return to automatic fan operation, press AUTO. 3. A. R Rear defroster...

Automatic Temperature Control (ATC) system with heated seats(if equipped) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to Units (Fahrenheit/Celsius) in the Driver Controls chapter. If your vehicle is equipped with a m...

MAX A/C: For maximum cooling performance, press , A/C, , and set the temperature to 60°F and the highest blower setting. 1. Defrost : Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog andthin ice. 2. Fan speed control: Press...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position to turn on the parking lamps. Rotateclockwise to the secondposition to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights nor...

Fog lamp control (if equipped) The headlamp control also operatesthe fog lamps. The fog lamps can beturned on only when the headlamp control is in the , or position and the high beams are notturned on. Pull headlamp control towards youto turn fog lamps on. The fog lampindicator light will illuminate...

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provideadequate lighting during these conditions. Failure to activate yourheadlamps under these conditions may result in a collis...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from thecente...

Replacing front parking lamp/turn signal/sidemarker bulbs 1. Make sure the headlamp controlis in the OFF position and open thehood. 2. At the top and inboard side of theheadlamp, peel the protective coverback from the lower screws andloosen the three retaining screws. 3. Once the three retaining scr...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Cupholders 2. Tissue holder in lid 3. Power point 4. Large utility compartment hasCoin holder slots and a Cardholderlocated inside on the passenger sideand a Pen holder on the lid. Use only soft...

Storage compartment Press the release on the door toopen the storage compartment. The storage compartment may beused to secure sunglasses or asimilar object. The front bin may beused to store small objects. Overhead Storage Bins • When on the overhead rail, adjacent bins must be pinned together.Bins...

POWER WINDOWS (IF EQUIPPED) Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the pro...

Note: The rear window switches will not illuminate when the window control is in the LOCKED position. Press the right side to restore the window controls. Power Sliding Back Window (if equipped) To operate the power sliding back window, the ignition switch must be inthe Run or Accessory position. • ...

Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equipped withan interior rear view mirror that hasan auto-dimming function (optionalon the driver’s side exterior mirror).The electronic day/night mirror willchange from the normal (highreflective) state to the non-glare(d...

Heated outside mirrors (if equipped) Heated mirrors remove ice, mist andfog. To activate the heated mirrors,press the rear defrost button R located on the climate control panel. Refer to Rear window defrost in the Climate Controls chapter for more information. On vehicles not equipped with reardefro...

Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. Do not use the speed control in heavy traffic or on roads thatare windi...

Audio control features Press to select: • AM, FM1, FM2 (if equipped) • CD (if equipped) • FES/DVD (if equipped) • SAT1, SAT2 or SAT3 (SatelliteRadio mode if equipped). • AUX (IN LINE) (if equipped) In AM, FM1, or FM2 mode: • Press and release SEEK to select the next preset station or press andhold S...

The moon roof has a built-in sliding shade that can be manually openedor closed when the glass panel is shut. To close the shade, pull it towardthe front of the vehicle. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a ...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined inthe “Programming” section, replace Step 2 with the...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. If the compass still appears to be inaccurate, a manualcalibration may be necessary. Refer to Compass calibration adjustment. Most geographic areas (zo...

1. Start the vehicle. 2. To enter the compass calibrationmode, press and hold the button forgreater than eight seconds. Thedisplay will then show CAL in thedisplay window. 3. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles untilCAL indicator turns off. As many as 5 complete circles ma...

DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same as the average fuel economy display. The running average fueleconomy is reinitialized to a factory default value if the battery isdisconnected. Averag...

CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap under the Fuel information section in the Maintenance and Specifications chapter. LOW TIRE PRESSURE (if equipped). Displayed when one or more tire...

POSITIVE RETENTION FLOOR MAT Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelet is over the pointed end of theretention post. Make sure that themat does not interfere ...

Tailgate removal Your tailgate is removable to allow more room for loading. Note: If equipped with a Reverse Camera System (RCS), do steps 1 through 3 before removing the tailgate. 1. Before removal of the tailgate,locate and disconnect the tailgatein-line connector under the pickupbox on the right-...

BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extendthe pickup box for larger loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the lever on each side of thebed extender to release it from thepickup box. 3. Lift the bed extender over ontothe tail...

To remove the bed extender: 1. Extend the bed extender. 2. Pull the lever on each side of thebed extender to unlock it. Make sure the locking clip screwsare loose before removing the bedextender. 3. Press the locking clips below themiddle bar and lift the bed extenderout of the channels on the “D” p...

Cross bars: Aluminum cross bars with T-slot channels in all four sides, and a latch mechanism that allows the end supports to snap over theexisting cleats. Cross bars are rated to hold loads up to 100 lb (45 kg)load evenly distributed between the two crossbars, and the T-slots aresized to accept ind...

Bed divider: This panel will keep small items up to 400 lb (180 kg) in position in the pickup box. Also includes T-slots to allow attachment ofindustry-standard roof rack accessories. • To remove bed divider, lift handle on each side and lift end supportshroud off of the cleat. • To install bed divi...

Side mounted tool bins: Watertight bins can be positioned at any point along the side rails and can be easily removed (even when full), andcarried to wherever the contents are needed. Each bin will hold up to60 lb (27 kg) of cargo, and has a drain plug for use as a cooler. Note: When multiple bins a...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to the SecuriLock™ passive anti-theft system section in this chapter for more i...

Conversely, a horn chirp followed by a honk will indicate the system isenabled. Pressing the control then the control will turn the feature ON if it was previously OFF, or OFF if it was previously ON. Thehorn will chirp once if autolock was deactivated or twice (one shortchirp and one long honk) if ...

2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parklamps will flash once more.If any of the doors are not properly closed the horn will make two quickchirps and the parklamps will...

Sounding a panic alarm Press to activate the alarm. Press again or turn the ignition to 2 (ACCESSORY) or 3 (ON) to deactivate. Note: The panic alarm will only operate when the ignition is in the 1 (OFF/LOCK) position. Memory seat/adjustable pedals feature (if equipped) The remote entry system can al...

Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. Ifall remote entry transmitters are not present during the programmingprocedure, the transmitters that are not present during pr...

• the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or...

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” c...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the1 (OFF/LOCK) position. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key,yo...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

The control is located on the outboard side of the seat cushion. Press the front or rear portion to tiltthe seat. Press the control to move the seatforward, backward, up or down. Memory seats/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat andadjustable ped...

Returning the seat to seating position Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull onthe seatback to ensure that it has fully latched. An unlatched seat...

and they move forward during pre-crash braking. The most effective wayto reduce the risk of unnecessary injuries is to make sure all occupantsare properly restrained. Accident statistics suggest that children aremuch safer when properly restrained in the rear seating positions than inthe front. Air ...

Front outboard safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to ...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an airbag supplemental restraint system (SR...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, push the releasebutton and remove the tongu...

2. Insert the belt into the clip on theback panel. Protect the stowed beltif you carry cargo this may damageor soil the belt. If the belt has been disconnected to carry large objects behind the seat,reconnect it as follows: 1. Remove the belt from thestowage clip on the back panel. 2. Buckle the sma...

shortened, but pinches the webbing to keep the lap portion from gettinglonger. The cinch tongue is designed to slip during a crash, so alwayswear the shoulder belt properly and don’t allow any slack in either thelap or shoulder portions. Before you can reach and latch a combination lap and shoulder ...

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm. 2)Never swing the safety belt around your n...

Shorten and fasten the belt whennot in use. Energy management retractors Your vehicle has a safety belt system equipped with energy managementretractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in acontrolled mann...

When to use the automatic locking mode • Anytime a child safety seat is installed in a front outboard passenger in a Regular Cab/ SuperCab/ SuperCrew or any rear seating position ofa SuperCab or SuperCrew. The Regular Cab front center seatbelt has acinch mechanism. Refer to Safety belt with locking ...

2. Grasp the shoulder portion andpull downward until the entire beltis extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Disconnect the combinat...

The driver and front outboard passenger safety belt pretensioners aredesigned to activate only during certain frontal or near-frontal collisionswith sufficient longitudinal deceleration. A safety belt bucklepretensioner is a device which tightens the webbing of the lap andshoulder belts during some ...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave theBelt-Minder 威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do ...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

outboard passenger from certain upper body injuries. The term“supplemental restraint” means the airbags are intended as a supplementto the safety belts. Airbags alone cannot protect as well as airbags plussafety belts in impacts for which the airbags are designed to deploy, andairbags do not offer a...

Additional equipment may affect the performance of the airbagsensors increasing the risk of injury. Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Children and airbags For additional important safetyinformation, read all inf...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal deceleration. The fact that the airbags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere no...

If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in acollision. Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a to...

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects inthe front seat, • the system determines that an infant is present in a rear-facing infantseat that is installed according...

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat, the passenger airbag will be disabled. Even though thepassenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated accord...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by l...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter. Carefully f...

2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to thechild seat manufacturer’s instructions. 4. Insert the belt tongue into the proper buckle for the center seatingposition until you hear a snap and feel it latch. Make ...

• F150 Regular Cab • F150 SuperCrew and SuperCab Front seat tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat andunder the head restraint. 3. Locate the correct anchor for the selected seating position...

Rear seat tether strap attachment There are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow) in the SuperCab andSuperCrew. These loops are to beused as both routing loops andanchor loops for up to three childsafety seat tether straps. Forexample, th...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare(if equi...

To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. If you are checking tire pressure when the tire is hot, (i.e. driven morethan 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires arehot from driving and it is norm...

cracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced. For your safety,tires that are damaged or show signs of excessive wear should not beused because they are...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over ...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. The Tire Pressure Monitoring System is NOT a substitute formanually checking tire pressure. The tire press...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

TPMS reset procedure (if applicable) This procedure is only required after tire rotation on vehicleswith different front and rear tire pressures. To determine if your vehicle requires two different pressures -one for the front tires and one for the rear tires - refer to the Safety Compliance Certifi...

Please take the tool with theprovided Velcro 威 strip on the back and mount it in the bottom rightcorner of your Owner’s Guide case(as shown) for safe keeping. If you find that the reset tool wasnot provided when delivered, hasbeen lost or no longer functions(the battery is not replaceable),please co...

If reset mode has been entered successfully, the horn will sound once,the TPMS indicator will flash and the message center will display TRAIN LF TIRE. If after repeated attempts to enter reset mode, the horn does not sound,the TPMS indicator does not flash and the message center does notdisplay TRAI...

illuminate while the tool is active. The horn will sound once within10 seconds to indicate the process was successful. Note: If a double horn chirp is heard, repeat the procedure. If a single horn chirp is not heard, move the vehicle to rotate the wheels at least a 1 ⁄ 4 -turn and repeat the procedu...

As in this example, the rear tires rotated to the front and properlyinflated to 50 psi (345 kPa) for the front axle would falsely illuminate thelow tire warning indicator as they are still trained for the rear positionswhich require 80 psi (552 kPa). Rotation, pressure adjustmentand successful compl...

• Remove the tire chains when they are no longer needed. Do not usetire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. VEHICLE LOADING – WITH AND WITHOUT A TRAILER This se...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight – refer...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide . Loaded vehicles may handle differently than unlo...

Crew Cab 4x4 (151” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L (with 17” tires) 3.73 12200 (5534) 6600 (2994) 4.6L (with 18” tires) 3.73 11700 (5307) 6100 (2767) 5.4L (with 17” tires) 3.55 14000 (6350) 8200 (3719) 5.4L (with 18” or 20” tires) 3.55 135...

Weight distributing hitch When hooking up a trailer using a load equalizing hitch, always use thefollowing procedure: 1. Park the unloaded vehicle on a level surface. With the ignition on andall doors closed, allow the vehicle to stand for several minutes so that itcan level. 2. Measure the height o...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourauthorized dealer or trailer rental agency for proper instructions andequipment for hooking up trailer lamps. Using a step bumper (if equipp...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. ACCESSORY, allows the electricalaccessories su...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Note: If the engine does not start on the fi...

heater is available, the addition of unleaded gasoline to your tank willimprove cold starting performance. Your vehicle is designed to operateon E 85 ethanol alone, unleaded gasoline alone, or any mixture of the two. See Choosing the right fuel in the Maintenance and Specifications chapter for more ...

• Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working order. How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment...

Parking brake To set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops. The BRAKE warning lamp will illuminate and will remain illuminateduntil the parking brake is released. Base, Base with Tachometer andFamily Carrier instrumentcluster Mid, Luxury, Limited andHarley-Dav...

During Traction Control™ operation,the traction control active light willilluminate and the engine will not“rev-up” when you push further onthe accelerator. This is normalsystem behavior and should be noreason for concern. Aggressive driving in any road conditions can cause you to losecontrol of you...

• Some noise is normal during operation. If the noise is excessive, checkfor a low power steering fluid level before seeking service by yourauthorized dealer. • Heavy or uneven steering efforts may be caused by a low powersteering fluid level. Check for a low power steering fluid level beforeseeking...

Vehicles with a higher center of gravity such as utility vehiclesand trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports carsare designed to perform satis...

2. Open the center console bin.Using a screwdriver, carefully pry offthe console finish panel surroundingthe shifter mechanism by inserting ascrewdriver into the latch slot asshown. 3. Remove console finish panelassembly to expose the inside of thegearshift. 4. Press and hold the white buttonlocated...

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor. • Allow...

Maximum downshift speeds 1 Shift from: Transfer case position (if equipped) 2H or 4H 4L D (Overdrive) - 4 55 mph (89 km/h) 21 mph (34 km/h) 4 - 3 45 mph (72 km/h) 17 mph (27 km/h) 3 - 2 35 mph (56 km/h) 13 mph (21 km/h) 2 - 1 20 mph (32 km/h) 7 mph (11 km/h) 1 Downshift at lower speeds when driving ...

To help avoid personal injury, always use caution when inreverse and when using the RSS. This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damagingthe vehicle. Th...

REVERSE CAMERA SYSTEM (IF EQUIPPED) The reverse camera system, locatedon the tailgate, provides a videoimage (which appears in the rearview mirror) of the area behind thevehicle. It adds assistance to thedriver while reversing or reverseparking the vehicle. To use the reverse camera system,place the...

Use the side mirrors and rear view mirror to get better coverage on bothsides and rear of the vehicle. When shifting out of reverse and into anyother gear, the image will remain on for a few seconds before it shuts offto assist in parking or trailer hookup. When towing, the reverse camera system wil...

dark. If either of the lamps are not operating, stop using the reversecamera system, at least in the dark, until the lamp(s) are replaced andfunctioning. Servicing • If the vehicle is in R (Reverse) and the screen in the rear view mirrorappears blue for three seconds and turns blank afterwards, the ...

Using a manual 4WD system (if equipped) 2H (2WD High) – Power to the rear wheels only; used for street and highway driving. Provides optimal smoothness and fuel economy at highspeeds. 4H (4WD High) – Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use...

Note: Some noise may be heard as the system shifts or engages; this is normal. Note: For proper operation in 4WD Low, ensure the transfer case shift lever is moved entirely rearward in to the 4L (4WD Low) position andthat the 4x4 Low light is illuminated. Note: Ideal 4L (4WD Low) shift conditions oc...

4H (Lock) - The “4X4 HI” light will illuminate in the instrument cluster when this position is selected. This position is not recommended for useon dry pavement. This position is only intended for severe winter oroff-road conditions, such as deep snow, ice or deep sand. Shifting between AWD (Auto) a...

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. •...

turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for. Avoid abr...

Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even 4WD vehicles can lose traction in slick mud. Aswhen you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until ...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

faster, because as in other vehicles, braking occurs at all four wheels. Donot become overconfident as to road conditions. Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears. In emergency stopping situa...

engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into thetransmission and cause internal transmission damage. Once through the water, always dry the brakes by moving yourvehicle slowly while applying light pressure on the brak...

• Headlight aim may require re-adjustment. • The tire air pressures recommended for general driving are found onthe vehicle’s Safety Certification Label. The maximum cold inflationpressure for the tire and associated load rating is imprinted on the tiresidewall. Tire air pressure may require re-adju...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card a...

HAZARD FLASHER CONTROL The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover, to the left of thefuse box. The access cover needs tobe removed to reset the fuel pumpshut-off switch. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are app...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F01 10A* Run/Accessory - Wipers,Instrument cluster, Audio forXL/STX F02 20A* Stop/Turn lamps, ABS, T/Telectric brake module, PCM (BOOsignal), turn signal mirrors,CHMSL F03 7.5A* Power mirrors, Memory seats andpedals F04...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F18 10A* Electrochromatic mirror, Heatedseats, BSM, Compass, RSS(Reverse Sensing System), Powerrail F19 10A* Restraints (Airbag module) F20 10A* Power rail F21 15A* Cluster keep alive power F22 10A* Delayed accessory po...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

2. Fully insert the jack handlethrough the bumper hole and intothe guide tube through the accesshole in the rear bumper. 3. Turn the handle counterclockwise until tire is lowered to the ground,the tire can be slid rearward and the cable is slightly slack. 4. Slide the retainer through the center of ...

6. If removed, install the spare tire lock (if equipped) into the bumperdrive tube with the spare tire lock key (if equipped) and jack handle. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (rotation, flat tire,...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionv...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. Ford recommends your vehicle be towed with a wheel lift or flatbed. Donot tow with a slingbelt. Ford Motor C...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Pr...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH SUPERCREW) Your leather seating surfaces have a clear, protective coating over theleather. For King Ranch SuperCrew leather seats, refer to separatesection in this chapter. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylClean...

• Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather. For more specific cleaninginformation, contact the King Ranch Saddle Shop at 1–800–282–KING(5464). • Do not spill coffee, ketchup, mustard, orange juice or oil-basedproducts on the leather ...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

2. Block the wheels. To reduce the risk of vehicle damage and/or personal burninjuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrumen...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1. Battery 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Power steering fluid reservoir 6. Air filter assembly 7. Engine oil filler cap 8. Engine oil dipstick 9. Transmission flu...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

• 4.6L/5.4L V8 engine 5. Locate and carefully remove the engine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes or between the MIN and MAX marks (depending on application), the oil level is accep...

• 4.6L/5.4L V8 engine • If the oil level is below the lowerhole or the MIN mark, addenough oil to raise the levelwithin the lower and upper holesor within the MIN-MAX range. • Oil levels above the upper hole or the MAX mark may cause enginedamage. Some oil must be removed from the engine by an autho...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product spec...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. Add the proper mixture of coolant and water to the cooling system...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

2. Arrange for the vehicle to be taken to an authorized dealer. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehic...

Fuel ethanol and gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harm...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

FFV (Flex Fuel Vehicle) Fuel Cap If your vehicle is FFV capable it will have a yellow colored fuel cap. Choosing the right fuel If your vehicle is a flexible fuel vehicle (FFV), use only UNLEADEDFUEL and FUEL ETHANOL (Ed75–Ed85). If your vehicle is not a flexible fuel vehicle (FFV), then only useUNL...

Octane recommendations Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily under mostdriving conditions while you areusing fuel with the recommendedoctane rating, see your authorized dealer to prevent any engine damage. Unleaded Gasoline Engines Your vehicle is d...

Unleaded Gasoline engines If you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of “Regular” unleadedgasoline. “Premium” unleaded gasoline is not recommended because itmay cause these problems to become more pronounced. If the prob...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a...

The EPA window sticker should be your guide for the fuel economycomparisons with other vehicles. It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of MPG (L/100 km)expected on the vehicle under optimum conditions. Your fuel economymay va...

detected by the OBD-II may not have symptoms that are apparent,continued driving with the Service engine soon indicator on can result in increased emissions, lower fuel economy, reduced engine andtransmission smoothness, and lead to more costly repairs. Readiness for Inspection/Maintenance (I/M) tes...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

Carefully read cautionary information on product label. ForMEDICAL EMERGENCY INFORMATION contact a physician or Poison Control Center immediately; on Ford-Motorcraft products call:1-800-959-3673 (FORD). Failure to follow these instructions may resultin personal injury. 1. Clean the reservoir cap bef...

Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and result in damage to internal transmission components. Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove th...

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be...

Changing the air filter element • 4.2L/4.6L engines 1. Loosen the clamp that securesthe air filter element in place. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter elementfrom the open end of the air filterhousing. 4. Install a new air filter element. 5. Reas...

2. Pull air filter tray assembly outtoward front of vehicle and lift airfilter element up and out of housing. The air filter box needs to be free of any debris before installing a newair filter. 3. Install a new air filter elementinto the tray assembly. 4. Return air filter tray to originalposition ...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ........................111 Air cleaner filter .......377–378, 380 Air conditioning ....................85, 87 Airbag supplementalrestraint system ................183–184 and child safety seats ............186description ..............................184disposal ......................

idle speed control ...................349lubrication specifications .......381refill capacities ........................381service points ..................341–343starting after a collision .........298 Engine block heater .................262 Engine oil ..................................345 checkin...

V Vehicle Identification Number(VIN) ..........................................387 Vehicle loading ..........................237 Ventilating your vehicle ...........262 W Warning lights (see Lights) .......12 Washer fluid ..............................344 Water, Driving through .............292 Wind...