Ford 2008 Expedition v.1- Manuals

Remember to pass on this Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle. Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration(e.g. ...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Your vehicle is not equipped with a snowplowing package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive yo...

Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, your vehicle may be equipped withfeatures and options that are different from the ones that are describedin this Owner’s Guide. A market unique supplement may be supplied that complements this boo...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Powertrain malfunction/reducedpower (RTT) (if equipped): Displays when the engine hasdefaulted to a ’li...

Low tire pressure warning (ifequipped): Illuminates when your tire pressure is low. If the lightremains ON at start up or whiledriving, the tire pressure should bechecked. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to ON, the light will ...

Key-in-ignition warning chime (if equipped): Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and thedriver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedr...

Tachometer: Indicates the engine speed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. Battery voltage gauge: Indicates the battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal...

AUDIO SYSTEMSQuick start — How to get going Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe operat...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

To view the station name or type: With RBDS ON, press TEXT/SCAN to toggle between displaying the station type (COUNTRY, ROCK, etc.) orthe station name (WYCD, WXYZ, etc.). BASS: Press MENU to reach the bass setting. Use / / SEEK, SEEK to adjust. Press OK to close and return to the main menu. TREB (Tr...

COMPRESS (Compression): Available only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display. Use / / SEEK, SEEK to toggle ON/OFF. When COMPRESS is ON, the system will bring the soft and loud CD passages together for a moreconsistent listening level. Press OK to close and return to...

6. / OKPlay/Pause: This control is operational in CD andDVD mode (if equipped). When aCD or DVD is playing in the FES system, press this control to play orpause the current CD/DVD. The CD/DVD status will display in the radiodisplay. OK: Use in various menu selections. If your vehicle is equipped wit...

12. Memory presets: To set a station, select the desired frequencyband, AM, FM1 or FM2. Tune to thedesired station. Press and hold a preset button until sound returns andPRESET # SAVED appears in the display. You can save up to 18 stations,six in AM, six in FM1 and FM2. In satellite radio mode (if e...

SPEEDVOL (Speed sensitive volume): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder withincreasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. The default setting is off; increasing your vehicle speed will not change the volume l...

5. Seek : In radio mode, press / to access the previous/next strong station. In CD mode, press / to access the previous/next CD track. In satellite radio mode (if equipped) , press SEEK, SEEK to seek to the previous/next channel. In CATEGORY MODE, press / to select a specific category (Jazz, Rock, N...

displayed. When the “>” indicator is active, press TEXT/SCAN and thenSEEK to view the additional display text. When the “<” indicator is active, press TEXT/SCAN and then SEEK to view the previous display text.Press and hold to hear a brief sampling of the next channels. Press againto stop. In ...

18. (CD eject): To eject a disc from the system, press . Select the correct slot number usingmemory presets 1–6. When ready, the system will eject the disc and thedisplay will read REMOVE CD. If the disc is not removed in 15 seconds,the system will reload the disc. To auto eject up to 6 CDs, press a...

When the rear seat controls are activated, rear seat passengers can usethe controls to change the playing media for all passengers (Single Playmode). In this mode, all speakers will play audio from the same mediasource for all passengers to hear. To activate the rear seat radio controls: • Press the...

The rear speakers will cut out once the speaker on/off control is pressed.The front speaker will remain playing for the front passengers. Press thecontrol again to deactivate the headphones. SINGLE PLAY illuminates inthe radio display and the fade control is enabled, signaling that Dual Playmode has...

• Wipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and...

• There are two different modes for MP3 disc playback: MP3 track mode(system default) and MP3 folder mode. For more information on trackand folder mode, refer to Sample MP3 structure in the following section. • MP3 track mode ignores any folder structure on the MP3 disc. Theplayer numbers each MP3 t...

Satellite radio information (if equipped) Satellite radio channels: SIRIUS broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. Formore information and a complete list of SIRIUS satellite radio channels,visit www.sirius.com in the United States, w...

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and play a variety of standard video game systems. TheDVD player is capable of playing standard DVDs, CDs, MP3s and iscompatible with CD-R/W, CD-R and cer...

2. Adjust the volume levels usingthe volume controls on the DVDsystem. To adjust display brightness: To decrease/increase the brightnesslevel on the display screen, pressthe brightness control on the DVDsystem. A display will appear at thebottom of the screen indicating thebrightness level. The brig...

16. Cursor /Brightness controls: Use the cursor controls to makevarious selections when in anymenu. When not in a menu, and inDVD mode, press / to adjust the brightness. A display bar will appear at the bottom of the screenindicating the brightness levels. Remote control Unless otherwise stated, all...

4. RETURN: Press to return to the previous menu screen. 5. ANGLE (DVD dependent): Press to select the angle to view the scene. 6. Channel A/B: Press to select either A or B headphones and then use the MEDIA control to select the desired playing media for theheadphones. 7. VOL (Volume): When in Singl...

19. MENU: Press to access the DVD disc menu for selections. Press MENU again when in the DVD disc menu to access the system set-upmenu. 20. SUBTITLE (DVD dependent): Press to turn the subtitle feature ON or OFF. 21. LANGUAGE (DVD dependent): Press to select the desired language. 22. ENTER: Press to ...

Headphones Wireless headphones Your FES system is equipped withtwo sets of battery powered, infraredwireless headphones. Two AAAbatteries are needed to operate theheadphones. (Batteries are included.) Additional infrared wirelessheadphones may be purchased foruse with the system. Also, wiredheadphon...

Wired headphones Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. You may purchase wired headphones for your FES ...

FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only. The radio will ignore button presses that affect the primary(speaker) audio source. LOCKED (disabled): The FES buttons are ...

use this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting/streaming via internet, intranets and/or other networks or inother electronic content distribution systems, such as pay-audio oraudio-on-demand appli...

Be sure to review User Manuals for video games and video gameequipment when used as auxiliary inputs for your Family EntertainmentSystem (FES). Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where they wi...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Distributes recircu...

4. REAR Rear temperature control: Press to enable the auxiliary system and to set the desired rear cabin airflow temperaturewith the front control. The rear cabin airflow temperature will match thedriver airflow temperature setting when only the center rear temperaturelight ( REAR ) is illuminated. ...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear thin ice or fog from thewindshield. 2. Rear temperature control: Press to enable th...

AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: Turn to select the desired fan speed. 2. Temperature/mode selection: The distribution of air from theoverhead and floor registers is basedon the temperature selected. Turnto select for comfort. To use the rear climate controls,ensure that REAR is...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp contro...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignitio...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Move the control to the full downposition, past detent, t...

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover one of the headlamps so no light from that lamphits the wall. 4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge towards theright. If this edge is not at thehorizontal refe...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • the remote entry controls arepressed and the ig...

Rear cargo lamp The dome lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is OFF(and switch is in the middleposition). With the i...

Function Number of bulbs Trade number Headlamps (low and high-beam) 2 H13/9008 Front sidemarker 2 194 Front park/turn lamps 2 3157 A Foglamps 2 9145 Front row map lamps 2 W5W Front row map/dome lamps 3 578 Rear cargo lamp 1 578 2nd row reading lamp 2 W5W Turn/tail/brake/sidemarker lamps 2 3157K or 4...

3. At the back of the headlamp,remove the two headlamp assemblyretainer bolts. 4. Slide headlamp assembly forwardand off the retaining tab to exposethe back of the headlamp assembly. 5. Rotate the bulb socketcounterclockwise and remove fromthe lamp assembly. 6. Carefully pull the bulb out of thesock...

6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing thelamp assembly with two torx screws. High-mount brakelamp To change the high-mountbrakelamp bulbs: 1. Remove the two screws holdingthe lamp assembly in pla...

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch isin the OFF position. 2. Remove the license lamp screwfrom the assembly. 3. Pull the lamp down and twist th...

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors areclosed and the interior lights haveautomatically turned off or theopposite mirror approach lamp hasturned off. 2. With a small flat tippedscrewdriver, insert the tip into theapproach light module slot lo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to either position. From either position, the control will automatically return to the INT 2or OFF position. TILT STEERING WHEEL 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering up or do...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Forward storage bin (if equipped) The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The ...

Cupholder/Ashtray (if equipped) The cupholder/ashtray is located onthe instrument panel. To open cupholder/ashtray, push inon the door and release. The doorwill spring out 1/4+ inches. Thenpull cupholder/ashtray assembly outthe remaining distance to utilize. Toclose, push assembly in completelyand r...

To operate ONE TOUCH DOWN: • Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press theswitch to any position to stop thewindow operation. If the switch is pressed and held tothe normal close or ONE TOUCH UP position during a ONE TOUCHDO...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. Accessory delay With accessory delay, the audio system, power wind...

With voice activated NavigationSystem The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up. Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirror...

Powerfold mirrors (if equipped) Rotate the 4–way adjustment switchto the center position. Press theswitch down to auto fold in anddown again to auto fold back todesign position. Powerfold the sidemirrors in carefully when drivingthrough a narrow space, like anautomatic car wash. The mirrors may be m...

Do not remove ice from the mirrors with a scraper or attempt toreadjust the mirror glass if it is frozen in place. These actionscould cause damage to the glass and mirrors. Signal indicator mirrors (if equipped) When the turn signal is activated,the lower portion of the mirrorhousing will blink. POW...

Automatic power deploy: • The running boards will extenddown and out when the doors areopened. Automatic power stow: • The running boards will return tothe stowed position when thedoors are closed. There will be atwo second delay before therunning boards move in to thestowed position. Manual power d...

Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board under body mounts to liftthe vehicle when jacking. Please utilize proper jacking points. Refer to Changing tires in the Roadside Emergencies chapter. In extreme climates, excessive ice bu...

• Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drive...

When programming your HomeLink 威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as requ...

door does not activate, press and hold the just-trained HomeLink 威 button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink 威 button is pressed and released. • If the indicator light blinks rapidly...

seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly after HomeLink 威 accepts the radio frequency signal. • Proceed with Step 3 in the “Programming” section. Operating the HomeLink 姞 Wirel...

For questions or comments, contact HomeLink 威 at www.homelink.com or 1–800–355–3515. STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. Y...

3. Locate the reset button on top ofthe compass sensor mounted behindthe mirror. 4. Press and hold the reset buttonon the compass module forapproximately 4 seconds until themessage center displays a selectionto change the current zone setting:ZONE <XX> RESET = CHANGE 5. Press and release the R...

5. The compass is now calibrated. Setup menu This menu allows the user, via the RESET stem located in theinstrument cluster, to interface and control the information displayed inthe message center for following selectable features: • System Check • Oil life • Units (English/Metric) • Autolamp • Auto...

Warning display Status Check brake system Warning can be reset. Will return after10 minutes. If within the 10 minutes,the condition is cleared and set again,it will not return until the initial 10minutes is up. Will return on ignitioncycle. XXX miles (km) to empty fuellevel low Park brake engaged Wa...

BRAKE FLUID LEVEL LOW. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. WASHER FLUID LEVEL LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the wash...

2. Waiting 4 seconds or pressing theRESET control cycles the messagecenter through each of the languagechoices. Selectable languages are English, Spanish, or French. 3. Press and hold the RESETcontrol for 2 seconds to set thelanguage choice. Units (English/Metric) 1. Select this function from theSET...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for 4seconds. The message center will display the last...

WASHER FLUID LEVEL LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. CHECK AIR SUSPENSION (if equipped). Displayed when the air suspension system is not operating prop...

2. Press and hold the RESETcontrol for 2 seconds and release.Oil life is set to 100% and “OIL LIFESET TO 100%” is displayed. FOR 4X4 LOW STOP VEHICLE (if equipped). Displayed when 4X4 LOW is selected while the vehicle is moving. For more information, referto Control trac four-wheel drive (4x4) opera...

POWER LIFTGATE (IF EQUIPPED) The liftgate can be operated by the following: • instrument panel control button • key fob button • outside release handle • control button in the rear cargo area Note: The liftgate can be reversed with a second press on a control button or key fob and can be manually cl...

To open the liftgate with outsideliftgate control button (manualactuation): 1. To open, unlock the liftgate withthe remote entry transmitter orpower door unlock control. 2. Push the control button to openthe liftgate. Note: For the best performance allow the power system to open theliftgate after re...

Make sure the liftgate is closed to prevent exhaust fumes frombeing drawn into the vehicle. If you must drive with the liftgate open, keep the vents open so outside air comes into the vehicle. Liftgate window To open the liftgate window, pushthe button on the left side of theliftgate handle above th...

Do not load any objects on the shelf that may obstruct yourvision or strike occupants of the vehicle in the case of a sudden stop or collision. Do not place people or pets on or under the parcel shelf. LUGGAGE RACK Your vehicle is equipped with a roofrack for transporting items on theexterior of the...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

• the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (RUN)position and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivati...

3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has beendisabled or a chirp followed by a honk to indicate the system has beenenabled. Message cen...

Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are closed. You must complete Steps 1–5 within 30 secondsor the procedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of...

CHILDPROOF DOOR LOCKS When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one door...

• 4–button remote • 5–button remote If any of the doors or liftgate are ajar, the horn will make two quickchirps, reminding you to properly close all doors. Opening the liftgate window Press the control to unlatch the liftgate window. • 4–button remote 2008 Expedition (exd) Owners Guide (post-2002-f...

Sounding a panic alarm Press this control to activate the alarm. The personal panic alarm will cycle the horn and parking lamps on/off. • 4–button remote • 5–button remote To deactivate the alarm, press the control again or turn the ignition tothe 2 (ACCESSORY) or 3 (ON) position. 2008 Expedition (e...

Memory feature The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the controlwill automatically move the seat, rearview mirrors, and adjustable pedalsto the desired memory position (the memory position corresponds to thetransmitt...

Deactivating the memory seat feature To deactivate this feature: 1. Press the SET control on thedriver’s seat. 2. Within 5 five seconds, press anycontrol on the remote transmitterwhich you would like to deactivateand then press the SET control onthe memory seat control. 3. Repeat this procedure for ...

4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown to ensure that the battery is fully seated in the battery housingcavity. 5. Snap the two halves back together. Note: Replacement of the battery will no...

• Repeat the previous step to program additional remote transmitters.The locks will cycle once to confirm that each remote transmitter hasbeen programmed. • When you have completed programming the remote transmitters, turnthe ignition to the 1 (OFF/LOCK) position or wait 20 seconds. Thedoors will ag...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Key information Your vehicle is supplied with two coded keys. Only a coded key will start...

SEATING Front row adjustable head restraints Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of these head restraints is to help limit headmotion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is loca...

Lift handle to move seat forward orbackward. Manual seat recliner (if equipped) Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in t...

Using the armrest (if equipped) Push the release control to movethe armrest up or down. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseat. Turn the lumbar support controlclockwise for more support. Turn the lumbar supportcounter-clockw...

Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Press the control to recline theseatback forward or rearward. Note: On vehicles with memory seats, to pre...

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat, powermirrors, and adjustable pedals totwo programmable positions. The memory seat control is locatedon the outboard side of the seatcushion. • To program position 1, move thedriver ...

To enter the 3rd row seat: 1. Fold down the 2nd row seat and release the handle. 2. Pull the handle up again until theseat releases from the floor. 3. Push the seat upward and fold itaway from the third row. Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not lat...

Note : If a squeak is heard from the latch area, the latch striker pinshould be wiped clean of dust ordebris. Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on...

3. To return the seat to the uprightposition, lift the seatback until thelatch is fully engaged. Before returning theseatback to its original position, make sure that cargo orany objects are not trappedunderneath the seatback. Afterreturning the seatback to itsoriginal position, pull on theseatback ...

Third row power folding seat (if equipped) Note : Be sure that the head restraints are folded down beforepowering the 3rd row seat down. The control buttons are located on theright-hand rear quarter trim panel(accessible from the liftgate area). Push the bottom portion of thecontrol button to lower ...

door, pressing the unlock button on the key fob, pressing anykeyless entry keypad button, or turning the ignition key. SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System™ provides an improved overall level offrontal crash protection to front seat occupants and is designed to helpfu...

Determining if the Personal Safety System™ is operational The Personal Safety System™ uses a warning light in the instrumentcluster or a back-up tone to indicate the condition of the system. Referto the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the P...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

• Front and rear seats 2. To unfasten, push the release button and remove the tongue from thebuckle. • Front and rear seats All safety restraints in the vehicle are combination lap and shoulder beltsexcept for the front row center lap belt (if equipped). Front center lap belt To fasten the front cen...

All combination lap/shoulder belts, other than the driver’s belt, have twomodes: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movements and locking in response to vehiclemovement. For example, if the driver brakes suddenly or turn...

2. Grasp the shoulder portion andpull downward until the entire beltis pulled out. 3. Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Unbuckle the combinati...

When the Safety Canopy™ system and/or the front airbags are activated,the safety belt pretensioners for the driver and right front passengerseating positions will be activated when the respective seatbelt isproperly buckled. The driver and the right front passenger safety belt system(including retra...

Second row comfort guide The second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the quarter trim paneland is used to adjust the comfort ofthe shoulder belt for smalleroccupants in the outboard secondrow seats. To adjust the comfort guide: 1. Slip the ...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the saf...

If... Then... The driver’s safety belt is notbuckled approximately 5seconds after the safety beltwarning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warning lightilluminates and the warning chimesounds for 6 seconds every 30seconds, repeating for approximately5 m...

Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bag system One time disable Any time the safety belt is buckled and then unbuckled during anignition ON cycle, Belt-Mi...

4. Within approximately 7 seconds of the light turning off, buckle thenunbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light willflash 4 times per second for 3 seconds. • This will ...

Additional equipment may affect the performance of the airbagsensors increasing the risk of injury. Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating positi...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensors, the system wiring, the airbag system readiness light, theairbag back up power and the airbag ignitors). Determining if the system is operational Th...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-fro...

If the Safety Canopy™system has deployed, the Safety Canopy™ will notfunction again unless replaced.The Safety Canopy™ system(including the A, B, C, and Dpillar trim) must be inspectedand serviced by an authorizeddealer. If the Safety Canopy™ is not replaced, the unrepaired areawill increase the ris...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by l...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

• LATCH lower anchors are recommended for use by children up to 48pounds (22 kg) in a child restraint. Top tether anchors can be usedfor children up to 60 pounds (27 kg) in a child restraint, and toprovide upper torso restraint for children up to 80 pounds (36 kg)using an upper torso harness and a b...

6. Before placing the child into the child seat, forcibly move the childseat from side to side and forward to make sure that the seat is heldsecurely. If the child seat moves excessively, repeat Steps 5 through 6, orproperly install the child seat in a different position. Attaching child safety seat...

Second row seating positions 1. Position the child safety seat on the seat cushion. 2. Locate the tether anchor at the bottom back of the seat. • outboard seating positions • center seating position (ifequipped) 3. Route the child safety seat tether strap under the head restraint(outboard seats) and...

5. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame. 6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cush...

3. Locate the anchor webbing loop for the seating position. • You may need to pull back thetop of the hinged panel along thebottom of the seat back to accessthe tether anchor. 4. Clip the tether strap through theanchor loop as shown. If the tether strap is clippedincorrectly, the child safety seat m...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

VEHICLE CHARACTERISTICS 4WD and AWD Systems (if equipped) A vehicle equipped with AWD or 4WD (when selected) has the ability touse all four wheels to power itself. This increases traction which mayenable you to safely drive over terrain and road conditions that aconventional two-wheel drive vehicle ...

How your vehicle differs from other vehicles SUV and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbody components. • Shorter –...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure. Note: If you o...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystan...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

Low TirePressureWarning Light Possiblecause Customer Action Required Solid WarningLight Tire(s)under-inflated 1. Check your tire pressure to ensuretires are properly inflated; refer to Inflating your tires in this chapter. 2. After inflating your tires to themanufacturer’s recommendedinflation press...

Low TirePressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For adescription of how the systemfunctions under these conditio...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use chains, it i...

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Label or Safety Compliance Certification Label: Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard e...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enoughcargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 x 9...

Engine Rear axle ratio Maximum GCWR - lb. (kg) Trailer weight range (0 - maximum) lb. (kg) Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x2 5.4L with standard trailer tow package All 12200 (5533) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6803) 0–8950 (0–4059) Expedi...

Weight distributing hitch When hooking up a trailer using a load equalizing hitch, always use thefollowing procedure: 1. Park the unloaded vehicle on a level surface. With the ignition in theON position and all doors closed, allow the vehicle to stand (withoutpassengers) for several minutes so that ...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourauthorized dealer or trailer rental agency for proper instructions andequipment for hooking up trailer lamps. Driving while you tow When tow...

• The trailer tongue weight should be 10–15% of the loaded trailerweight. • If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Main...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsil...

4. Make sure the parking brake isset. 5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you ...

3. After idling for a few seconds, apply the brake, shift into gear anddrive. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine stillfails to start, press the accelerator to the floor and try again; this willall...

• Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been operating for approxim...

If you are driving down a long or steep hill, shift to a lower gear.Do not apply your brakes continuously, as they may overheat and become less effective. Anti-lock brake system (ABS) On ABS-equipped vehicles, a noise from the hydraulic pump motor andpulsation in the pedal may be observed during ABS...

With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminated with parking brakereleased. (If your brake warning lamp illuminates, have your vehicleserviced immediately.) Parking brake Apply the parking brake w...

Aggressive driving on any road condition can cause you to losecontrol of your vehicle increasing the risk of personal injury or property damage. The occurrence of an AdvanceTrac 威 with RSC event is an indication that at least some of the tires have exceeded theirability to grip the road; this could ...

If the steering wanders or pulls, check for: • Underinflated tire(s) on any wheel(s) • Uneven vehicle loading • High crown in center of road • High crosswinds • Wheels out of alignment • Loose or worn suspension components Variable assist steering Your vehicle is equipped with variable assist power ...

On vehicles equipped with air suspension, turn the airsuspension and the ignition switch off prior to jacking, hoisting or towing your vehicle. LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under norm...

AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock – column-shift transmission This vehicle is equipped with a park/brake-shift interlock feature thatprevents the gearshift lever from being moved from P (Park) when theignition is in the ON position unless brake pedal is depressed. If you cannot ...

Do not drive your vehicle until you verify that the brakelampsare working. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the ...

5. Start the vehicle and release the parking brake. Do not drive your vehicle until you verify that the brakelampsare working. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehic...

Audible Warnings Distance to Object Warning Speed above 2.5 mph (4 km/h) up to 1.6 feet (.5 meters) Solid 1.6 feet (.5 meters) to 3.1 feet(1 meter) Fast beep 3.1 feet (1 meter) to 5.7 feet(1.8 meters) Medium/fast beep 5.7 feet (1.8 meters) to 9 feet(2.8 meters) Medium beep 9 feet (2.8 meters) to 13 ...

The radar sensor is located behind the rear bumper/fascia. Alwayskeep the rear bumper/fascia free from snow, ice and largeaccumulations of dirt. These elements may cause the system tooperate inaccurately. If the vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sen...

When towing, the reverse camera system will only see what is beingtowed behind the vehicle; this might not provide adequate coverage as itusually provides in normal operation and some objects might not beseen. The camera lens for the reverse camera system is located on the liftgate,above the license...

Servicing • If the vehicle is in R (Reverse) and the screen in the rear view mirrorappears blue for three seconds and turns blank afterwards, the camerais not working properly; have the system inspected by your authorizeddealer. • If the image comes on while the vehicle is not in reverse, have thesy...

conditions. If these messages display when driving in 2H, contact yourauthorized dealer as soon as possible. Refer to Warning lights and chimes in the Instrument Cluster chapter. • 4X4 AUTO – displays when 4A is selected. • 4X4 – displays when 4H is selected. • 4X4 LOW – displays when 4L is selected...

The AdvanceTrac 威 with RSC stability enhancement system can be turned off manually by pressing the AdvanceTrac 威 with RSC button (refer to AdvanceTrac 威 with Roll Stability Control (RSC) Stability Enhancement System in this chapter) while operating in 2H, 4A or 4H while driving in deep sand, very de...

Driving off-road with truck and utility vehicles Four–wheel drive vehicles are specially equipped for driving on sand,snow, mud and rough terrain and have operating characteristics that aresomewhat different from conventional vehicles, both on and off the road. The AdvanceTrac 威 with RSC stability e...

pavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. • It may be safer to stay on the apron or shoulder of the road and slowdown gradually before returning to the pavement. You may losecontrol if you do not slow down or if you turn t...

Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and a...

slick mud. As when you are driving over sand, apply the acceleratorslowly and avoid spinning your wheels. If the vehicle does slide, steer inthe direction of the slide until you regain control of the vehicle. If the transmission, transfer case, front axle or rear axle are submergedin water, their fl...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in...

Push in the flasher control and all front and rear direction signals willflash. Press the flasher control again to turn them off. Use it when yourvehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery. FUEL PUMP SHUT-OF...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accessto the fuse box, pull the paneltoward you and swing it out awayfrom the side and remove it. Toreinstall it, line up the tabs with thegrooves on the panel, t...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electri...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 65 10A* Air suspension logic 66 — Not used 67 10A* Blower coil 68 — Not used 69 30A* Run/Start – passenger compartment fusepanel 70 20A* PCM (sensors) – EFC, A/C clutch coil 71 5A* Fuel coil, ISP-R 72 20A* PCM (ignition coils) 73...

Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longerfunction. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increasedr...

• Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one di...

Stopping and securing the vehicle 1. Park on a level surface, activatethe hazard flashers and set theparking brake. 2. Place the gearshift in P (Park)and turn the engine OFF. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Item Loc...

Removing the spare tire 1. Remove the jack handle andwinch extension from the tray andassemble them. 2. Open the spare tire winch accessplug in the bottom of thecompartment for the jack and toolstray. 3. Insert the winch extension toolassembly through the access hole inthe floor and engage the winch...

Turn off the running boards(if equipped) before jacking or placing any object under thevehicle. Never place your handbetween the extended runningboard and the vehicle. A movingrunning board may cause injury. To lessen the risk of personal injury, do not put any part of yourbody under the vehicle whi...

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc thatcontacts the wheel. Ensure that any fasteners that attach the rotor tothe hub are secured so they do not interf...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the engine compartment, near the washer fluidbottle. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-)termin...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – 2008 Expedition (exd) Owners Guid...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar comp...

• It is especially important to wash the vehicle regularly during thewinter months, as dirt and road salt are difficult to remove and causedamage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppingsand insect deposits because they can cause damage to the vehicle’s...

racks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer has touch-up paint to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jamb) toyour auth...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. 5.4L 3V ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These prod...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Apply Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11-A) [InCanada use Motorcraft Multi-Purpose Cleaner (CXC-101)] to the wipedarea and spread around evenly. 3. Apply more Motorcraft cleaner to a clean, white, cotton cloth andpress ...

LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH EXPEDITION) Your leather seating surfaces have a clear, protective coating over theleather. For King Ranch Expedition leather seats, refer to separatesection in this chapter. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCle...

• Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather. For more specific cleaninginformation, contact the King Ranch Saddle Shop at 1–800–282–KING(5464). • Do not spill coffee, ketchup, mustard, orange juice or oil-basedproducts on the leather ...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. 2008 Expediti...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 3V–V8 engine 1. Windshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap 9. Battery 2...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the blade dow...

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm until an audiblesnap is heard. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for che...

• If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the bat...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif...

swallowed can cause death or permanent injury. If fuel is swallowed,call a physician immediately, even if no symptoms are immediatelyapparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

At the next opportunity, safely pull off of the road, remove the fuel fillercap, align the cap properly and reinstall it. The check fuel cap lamp or “check fuel cap” message may not reset immediately; it may take severaldriving cycles for the check fuel cap lamp or “check fuel cap” message to turn o...

empty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might no...

economy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general, lower temperatures give lower fuel economy. Driving style — good driving and fuel economy habits Give consideration to the lists that follow and ...

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may reduce fuel economy (as much as1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example; bugdeflec...

If the vehicle’s engine or transmission has just been serviced, or thebattery has recently run down or been replaced, the OBD-II system mayindicate that the vehicle is not ready for I/M testing. To determine if thevehicle is ready for I/M testing, turn the ignition key to the ON positionfor 15 secon...

sure to put the cap back on the reservoir. Refer to Maintenance product specifications and capacities in this chapter for the proper fluid type. BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX”...

To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Locate the Mass Air Flow Sensorelectrical connector on the air outlettube. This connector will ...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Mobile-Ease™ hands-free communication system Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yo...

A ABS (see Brakes) .....................271 Accessory delay ........................107 AdvanceTrac ..............................273 Air cleaner filter .......372–373, 375 Air suspension ...........................278 description ..............................278 Airbag supplemental restraintsystem...

change oil soon warning,message center .......................349checking and adding ..............349dipstick ....................................349filter, specifications ........351, 375recommendations ...................351refill capacities ........................376specifications ................