Ford 2008 Escape v.1- Manuals

This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to yourparticular vehicle. Furthermore, due to printing cycles it may describeoptions before they are generally available. Remember to pass on this Owner’s Guide when reselling...

Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning andlubrication materials are significantsteps towards this aim. Information in this respect is highlighted in thisguide with the tree symbol. BREAKING...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

Check engine: The Check Engine indicator light illuminates when theignition is first turned to the RUNposition to check the bulb and toindicate whether the vehicle is ready for Inspection/Maintenance (I/M)testing. Normally, the ⬙ Check Engine ⬙ light will stay on until the engine is cranked, then tu...

fluid level or a brake system malfunction and the brake system should beinspected immediately by your authorized dealer. Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have th...

Traction Control 娂 : Illuminates when the Traction Control 娂 is active. If the light remains on, havethe system serviced immediately,refer to the Driving chapter for more information. Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains ON atstart up or while dr...

GAUGES Standard instrument cluster gauges Optional instrument cluster gauges Speedometer: Indicates the current vehicle speed. 2008 Escape (204) Owners Guide (post-2002-fmt)USA (fus) Instrument Cluster 17

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engine and let the eng...

AUDIO SYSTEMS AM/FM/single CD/in-dash CD6/MP3 satellite compatible soundsystem Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither fr...

RDS ON/OFF: Available only in FM mode. This feature allows you to search RDS-equipped stations for a certain category of music format:CLASSIC, COUNTRY, JAZZ/RB, ROCK, etc. To activate, press MENU repeatedly until RDS (ON/OFF) appears in the display. Use SEEK/TRACK to toggle RDS ON/OFF. When RDS is O...

In satellite radio mode (if equipped), use to select from various satellite radio categories. To change categories in satellite radio mode,press CAT/FOLD. The active category will appear in the display. Press SEEK/TRACK or turn the TUNE knob left/right to scroll through the available categories. Pre...

Auxiliary input jack Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To ...

6. Press AUX on the vehicle radio repeatedly until LINE IN appears inthe display.You should hear audio from your portable music player although it maybe low. 7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

• Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result in anaudio mute. Unlike AM/FM audible static, you will hear an audio mute when there isa satellite radio signal interference. Your radio display may display NOSIGNAL to i...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. You are in a location that i...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. R Rear defroster: Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this chapter for more information. 3. Defrost: D...

9. Temperature control: Controls the temperature of the airflow in the vehicle. 10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter. 11. Recirculated air: Press to activate/deactivate a...

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. • To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.” For maximum cooling performance in MAX A/C mode: 1. Select MAX A/C. 2....

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED) 1. AUTO/Driver temperature: Press to engage full automatic operation. The system will automatically determine fan speed, airflowdistribution, A/C on or off, and outside or recirculated air, to heat or coolthe vehicle to reach the desired temperature. ...

5. Power/ : Press to activate/deactivate the climate control system. When the system is off, outside air is shut out. Turn to manuallyincrease/decrease the fan speed. The manual fan speed setting willappear on the left side of the display. To return to automatic fanoperation, press AUTO. 6. : Distri...

13. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engagesautomatically in AUTO, MAX A/C, (defrost) and (floor/defrost). 14. Driver heated seat control (if equipped): Press to activate/adjective the driver heated seat. See...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument p...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the h...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the i...

4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge of highintensity light towards the right. Ifthis edge is not at the horizontalreference line, the beam will need tobe adjusted. 5. Locate the vertical adjuster onthe headlamp, then use a 4 mmsocket to turn the ad...

The dome lamp control has threepositions: • OFF: In this position, the lampwill not illuminate. • DOOR: In this position, the domelamp will illuminate only when adoor is opened and will remainilluminated for 25 seconds afterthe door is shut. • ON: In this position, the lamp will remain illuminated. ...

Interior lighting battery saver The interior lamps will automatically extinguish after 10 minutes whenthe ignition key is in OFF/LOCK position, a door has been left open orthe interior lamp controls are in the ON position. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize p...

4. Pull bulb straight out of socketand push in the new bulb. 5. Install the bulb socket into thelamp assembly and rotate clockwise. 6. To install, carefully press thelamp assembly into liftgate. Replacing foglamp bulbs (if equipped) 1. Make sure the foglamp switch isin the OFF position. 2. From unde...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: INT 2 — Normal speed operation ofrear wiper. INT 1 — Intermittent operation ofrear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold a...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamps. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment (if equipped) Press the release on the door toopen the storag...

The auxiliary power point is locatedin the instrument panel. A second auxiliary power point islocated on the rear side of thecenter console. Do not use the power point foroperating the cigarette lighterelement (if equipped). To prevent the fuse from beingblown, do not use the powerpoint(s) over the ...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. One touch down Allows the driver’s window to openfully without holding the controldown. Push the switch completelydo...

Automatic dimming rear view mirror (if equipped) Your vehicle may be equipped withan inside rear view mirror which hasan auto-dimming function. Theelectronic day/night mirror willchange from the normal (highreflective) state to the non-glare(darkened) state when bright lights (glare) reach the mirro...

Compass zone adjustment 1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap. 2. Turn ignition to the ON position. 3. Locate the reset button on top ofthe compass sensor mounted behindthe mirror. 4. Press and hold the reset buttonon the compass module fo...

Compass calibration adjustment Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessories (heater/air conditioning, wipers, etc.) and make sure allvehicle doors are shut. 1. Start the vehicle. 2. Locate th...

Turning off speed control There are two ways to turn off thespeed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allo...

If you open and close the moon roof repeatedly, the moon roof motormay overheat and shut down for 45 seconds while the motor cools. MESSAGE CENTER (IF EQUIPPED) With the ignition in the RUNposition, the message center,located on your instrument cluster,displays important vehicleinformation through a...

Distance to empty (DTE) Selecting this function from theINFO menu will give you anestimate of how far you can drivewith the fuel remaining in your tankunder normal driving conditions.Remember to turn the ignition OFFwhen refueling your vehicle. Otherwise, the display will not show theaddition of fue...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for fourseconds. The message center will display the l...

LIFTGATE • To open the liftgate window,unlock the liftgate (with thepower door locks or the remoteentry) and push the right side control button under the licenseplate lamp shield. • To open the liftgate, unlock theliftgate (with the power doorlocks or the remote entry) andpush the middle control but...

2. The smaller compartment contains the jack kit. There is also extrastorage space for customer use. The lid on the small compartment isaccessible and secured by two snap features. This storage compartment is not designed to restrain objectsduring a collision with the lid removed. LUGGAGE RACK Your ...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote keyless entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors Turn the key in the door cylinder to unlock the driver’s door only. Allother doors will remain locked. Locking the doors Turn the key in the door cylinder t...

Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Before following the activation or deactivation procedures, make surethat the anti-theft system is not armed, ignition is in the 1 (OFF/LOCK)position, and all vehicle doors, liftgate and liftgate window ...

Message center procedure For information on activating/deactivating the autolock feature using thevehicle’s message center (if equipped), refer to Message center information in the Driver Controls chapter. Autounlock The autounlock feature will unlock all the doors when: • the ignition is in the 3 (...

2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirpone time to confi...

CHILDPROOF DOOR LOCKS When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. NOTE: Setting the lock for on...

The typical operating range for yourIKT is approximately 33 feet(10 meters). A decrease inoperating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next toyour vehicle. The IKT allows you to: • remotely unlock the veh...

Switching from two step to one step door unlocking Unlocking can be switched between two step and one step door unlocking by pressing and holding both and buttons simultaneously on the remote entry transmitter for approximately 4seconds. The turn signal will flash twice to indicate that the vehicle ...

To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing o...

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter or the keyless entry system keypad isused to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, ...

Unlocking and locking the doors and liftgate using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of eachother. The interior lamps will illuminate. To unlock all doors and liftgate, press the 3 • 4 ...

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please visit an authorized dealer to purchase additionalspare or replacement keys. Programming spare keys You can program your own Integrated Keyhead Transmi...

5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.Keep the ignition in the 3 (RUN) position for at least three seconds, butno more than 10 seconds. 6. Turn the ignition to the 1 (LOCK) position and remove the secondpreviously programmed coded key from the ignition. 7. Within tw...

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatbac...

Push side control and push down onhead restraint to lower it. Adjusting the front manual seat (if equipped) Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving...

Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the button located on theinstrument panel to activate. • Push again to deactivate. The heated seats will activa...

The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head. Push control to lower or removehead restraint. Folding down rear seats 1. Raise the rear seat head restraintand remove. 2. Place the head restraint underthe fro...

3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the seat back foldingpa...

2. Rotate seat cushion down into theseating position making sure thatthe seat cushion is locked into placeand that the safety belt buckles areexposed. Make sure safety belt buckleheads are through elastic holders on seat backs. Safety beltbuckles may break if they aretrapped underneath the seatbacka...

To remove the rear cushion 1. Lift the yellow tab to release thehinges. 2. Pull the cushion to the outboardside of the vehicle. To install the rear cushion 1. Push the cushion to the inboardside of the vehicle. 2. Make sure that the hinges arelocked into place. SAFETY RESTRAINTS Personal Safety Syst...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System 娂 to tailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower air...

Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers. Automatic locking mode When to use the automati...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. After any vehicle collision, the safety belt systems at all seatingpositions ...

authorized dealer finds that the belts do not show damage and continueto operate properly, they do not need to be replaced. Safety beltassemblies not in use during a collision should also be inspected andreplaced if either damage or improper operation is noted. Failure to inspect and if necessary re...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will ...

Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bag system One time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safety belt fo...

• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, buckle then unbuckle thesafety belt 9 times, ending in the unbuckled state. (Step 3 must becompleted within 50 seconds after the safety belt warning light turnsoff.)...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Modifications to the front end of the vehicle, including frame,bumper, front end body structure, tow hooks and B-pillar surrounding parts may affect the performance of the ...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the airbag sensors to closean electrical circuit that initiatesairbag inflation. The fact that theairbags did not inflate in a collisi...

• seat-mounted side airbags. Refer to Seat-mounted side airbag system later in this chapter • Safety Canopy 娂 system. Refer to Safety Canopy 娂 system later in this chapter. • one or more impact and safing sensors. • Safety belt pretensioners • a readiness light and tone. • diagnostic module. • and t...

The front passenger sensing system is designed to enable (may inflate)the front passenger’s frontal airbag anytime the system senses that aperson of adult size is sitting properly in the front passenger seat. • When the front passenger sensing system enables the front passengerfrontal airbag (may in...

Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in seriousinjury or death in a crash.Always sit upright against your seatback, with your feet on the floor. The ...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the status of the system. Refer to Airbag readiness section ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation.The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot function properly in the ev...

If the shoulder belt portion of a combination lap and shoulder belt canbe positioned so it does not cross or rest in front of the child’s face orneck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit. Do not...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter. Carefully f...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

VEHICLE CHARACTERISTICS 4WD and AWD Systems (if equipped) A vehicle equipped with AWD or 4WD (when selected) has the ability touse all four wheels to power itself. This increases traction which mayenable you to safely drive over terrain and road conditions that aconventional two-wheel drive vehicle ...

How your vehicle differs from other vehicles SUV and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbody components. • Shorter –...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure. Note: If you o...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

designating where it was manufactured, the next two are the tire sizecode and the last four numbers represent the week and year the tire wasbuilt. For example, the numbers 317 mean the 31st week of 1997. After2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001. The numbe...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystan...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

The Tire Pressure Monitoring System is NOT a substitute formanually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge, see Inflating your tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tir...

To restore the full functionality of the Tire Pressure Monitoring System,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with TPMS in this section. When you believe your system is not operating properly The main function of ...

Low TirePressureWarning Light Possiblecause Customer Action Required FlashingWarning Light Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For adescription of how the systemfunctions under these conditio...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

cement to your home? If you and your friend each weigh 220 lb.(99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400- 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity tocarry that much weight. In metric units, the calculation would be:635 kg - (2 x 99 kg) - (12 x 45 ...

• Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to your scheduled maintenance information for more information. • Do not tow a trailer until your vehicle has been driven at least...

4x4 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - lb. (kg) Trailer Weight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m) 2 2.3L w/automatic transmission 5140 (2331) 1500 (680) 24 (2.2) 3.0L w/automatic transmission 7240 (3284) 3500 ( 1588) 30 (2.8) Notes: For...

Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to hook retainers on thevehicle. To connec...

• Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. (For additional information, refer to Understanding the gearshift positions of the 4–speed automatictransmission in the Drivin...

When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge ofthe rear bumper. • do not allow waves to break higher than 6 inches (15 cm) above thebottom edge of the rear bumper. Exceeding these limits may allow water to enter vehi...

STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand steering column and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. RUN, all electrical circuitsoperational and warning lights willilluminate. Thi...

Starting the engine 1. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. This condition mayoccur when: • the front wheels are turned • a front wheel is against the curb 2. Turn the key to 4 (STAR...

strongly recommended if you live in a region where temperatures reach-10°F (-23°C) or below. For best results, plug the heater in at least threehours before starting the vehicle. The heater can be plugged in the nightbefore starting the vehicle. To reduce the risk of electrical shock, do not use you...

distance. The ABS will be activated immediately, allowing you to retainsteering control during hard braking and on slippery surfaces. However,the ABS does not decrease stopping distance. ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ift...

Traction Control Traction Control helps your vehicle maintain traction, when driving onslippery and/or hilly road surfaces, by detecting and controlling wheelspin. Excessive wheel spin is controlled by momentarily reducing enginepower and/or applying the anti-lock brakes. Traction Control is a drive...

• Driving over a patch of ice. • Changing lanes on a snow-rutted road. • Entering a snow-free road from a snow-covered side street, or viceversa. • Entering a paved road from a gravel road, or vice versa. • Driving on slick surfaces. • Cornering while towing a heavily loaded trailer (refer to Traile...

AdvanceTrac 威 with RSC Features Buttonfunctions “Sliding car” icon RSC ESC Engine Traction Control Brake Traction Control Buttonpressed andheld morethan fiveseconds Flashes then illuminated solid Disabled below 25 mph (40 km/h) Disabled below 25 mph (40 km/h) Disabled below 25 mph (40 km/h) Disabled...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the RUN position unless brake pedal is depressed. If you cannot move the gearshift...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your authorized dealer as soon as possible. Driving with an automatic overdrive transaxle Your automatic overdrive transaxleprovides fully automatic operation ineither D...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transaxle has a starter interlock that prevents cranking theengine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put t...

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts during light to moderate accelerations and cruises (for best fuel economy) Shift from: 1-2 10 mph (16 km/h) 2-3 20 mph (32 km/h) 3-4 32 mph (52 km/h) 4-5 37 mph (60 km/h) Reverse Make sure that your ve...

To help avoid personal injury, please read and understand thelimitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large andfixed) objects when moving in reverse on a flat surface at “parkingspeeds”. Inclement weather may also affe...

FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. Your vehicle is equipped with an intelligent 4WD System thatcontinuously monitors vehicle conditions and automatically adjusts t...

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. •...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your authorized dealer. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable e...

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through highwa...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slip...

and adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy off-road usage. DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot know...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card a...

HAZARD FLASHER CONTROL The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the...

This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5....

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 44 10A Not used (spare) 45 5A Front wiper logic, Blower motorrelay 46 7.5A OCS (restraints), PADI(restraints) 47 30A Circuit Breaker Power windows, Moon roof 48 — Delayed accessory relay Power distribution box The power...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 36 — Not used 37 — Not used * Mini fuse ** Cartridge fuse CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly mov...

For vehicles equipped with 4WD, it is not recommended that the vehiclebe operated in 4WD modes with a temporary emergency spare tire. If4WD operation is necessary, do not operate above speeds of 10 mph(16 km/h) or for distances above 50 miles (80 km). 3. Full-size dissimilar spare without label on w...

Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through theaccess hole in the rear bumper. 2. Turn the handle counterclockwiseand lower the spare tire until it canbe sl...

5. Use the lug wrench to remove thelug nut from the spare tire tether. 6. If not replacing the spare or flattire to the underbody storage area,raise winch up into the installedposition. 7. Use the attached fastener strap(2) to tie the tether end to thewinch actuator shaft (if equipped). Tire change ...

Do not attempt to change a tire on the side of the vehicle closeto moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 1. Block the diagonally oppositewheel. 2. Loosen each wheel lug nutone-half turn counterclockwise butdo not ...

Before placing the jack under the vehicle, NOTE the jack locations: • Front View shown from rear of front tire.Position the jack directly below theprotruding bolt. 2008 Escape (204) Owners Guide (post-2002-fmt)USA (fus) Roadside Emergencies 223

• Rear View shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm. 3. Position the jack according to theguides and turn the jack handleclockwise until the tire is amaximum of 1 inch (25 mm) off theground. Never use the differentials as ajacking point. To l...

1. Place tire on end with valve stemfacing rearward, away from vehicle. 2. Place tether into bolt holes inwheel and attach lug nut using lugwrench. 3. Lay the tire on the ground with the valve stem facing down. If yourvehicle is equipped with aluminum wheels, remove the wheel ornament. 4. Slide the ...

3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other movingparts. 4. Check all battery terminals and remove any excessive corrosion beforeyou attach th...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

• Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton cloth, then with a clean and dry whitecotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner(ZC-38-A) on the instrument panel and interior tr...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or gl...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. To reduce the risk of vehicle damage and/or person...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine coolant bleed valve 9. Engine oi...

3.0L DOHC V6 Duratec engine 1. Engine coolant reservoir 2. Automatic transmission fluid dipstick 3. Brake fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil dipstick 8. Engine oil filler cap 9. Windshield washer fluid reservoir 2008 Escape (204) Owners Guide (p...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause s...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. Turn the bladeat a right angle to the arm. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wi...

To replace the wiper blade: 1. Grab the wiper arm just belowthe blade attachment and pull it asfar away from the glass as possible.Do not use excessive force becauseit can break the wiper arm at theheel. Hold it there until the nextstep. 2. Grab the wiper blade with yourother hand and use your finge...

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within the MIN and MAX marks or the lower andupper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark or the lo...

• 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above the MAXmark or upper hole may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, maydarken the color of Motorcraft Premium Gold Engine Coolant fromyellow to golden tan. Note: For the 2.3L engine, when adding more than 1 quart (.95L) of coolant it is necessa...

• 2.3L coolant bleed valve 5. For the 2.3L engine ONLY, open the coolant bleed valve on the back ofthe engine water outlet. 6. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “COLD FILL RANGE” or the “FULL COLD” level onthe reservoir. 7. For the 2.3L engin...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to anauthorized dealer as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals f...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. Re...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding 1 gallon (3.8L) of fuel is en...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, s...

vehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20minutes of stop-and-go driving with at least four 30-second idle periods. Allow the vehicle to sit for a...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick blade. Refer to Maintenance product specifications and capacities in this chapter. Use of a non-approved automatic transmission fluid...

When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is r...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Mobile-Ease 娂 hands-free communication system Remote start system Vehicle security system Wheel locks Not all accessories are available for all models. For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When ad...

A Accessory delay ..........................57 AdvanceTrac ..............................184 Air cleaner filter ...............280, 282 Air conditioning automatic temperaturecontrol system ..........................37manual heating and airconditioning system .................34 Airbag supplemental r...