Ford 2007 Explorer Sport Trac - Manuals

Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g.collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emerg...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type,failur...

Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped withfeatures and options that are different from the ones that are describedin this Owner’s Guide; therefore, a supplement has been supplied that complements this book. By referring ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

bulb works. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information. Note: Some Warning Lights will display in the Message Center as words and function the same as the warning light. Note: Depending on which options your vehicle has,...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

information on this system, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Serviceengine soon warning light to come o...

Four wheel drive high (ifequipped): Illuminates when four-wheel drive is engaged. If thelight fails to illuminate when the ignition is turned ON, or remains on,have the system serviced immediately by your authorized dealer. Door ajar: Illuminates when the ignition is in the ON position andany door i...

Parking brake ON warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph(5 km/h). Message center activation chime: Sounds when the following warnings; DOOR AJAR, LOW FUEL LEVEL or LOW TIRE PRESSUREappear in the message center display for t...

AUDIO SYSTEMS AM/FM Single CD/MP3 Satellite Compatible sound system(if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither ...

6. Play/Pause: This control is operational in CD mode. When a CDis playing, press to pause or play thecurrent CD. The CD status willdisplay in the radio display. 7. SHUFFLE: Press to play tracks in random order. 8. FOLDER : In folder mode, press to access next folder on MP3discs, if available. 9. FO...

2. MUTE/Phone: Press to mute the playing media. Press again to returnto the playing media. 3. MENU: Press to toggle through the following modes: Setting the clock: Press until SET HOURS or SET MINUTES is displayed. Press / to adjust the hours/minutes. CATEGORY (Satellite Radio if equipped): Press ME...

When the six strongest stations are filled, the station stored in preset 1 willbegin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Use / to turn on/off. Bass: Press / to adjust the bass setting. Treble: Press / to adjust the treble ...

16. CD: Press to enter CD mode. If a CD is already loaded into thesystem, CD play will begin where itended last. If no CD is loaded, NO DISC will appear in the display. 17. LOAD: Press to load a CD. Press LOAD and a memory presetto load to a specific slot. Press andhold to autoload up to six CDs. 18...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm)audio compact discs only. Due to technical incompatibility, certainrecordable and re-recordable compact discs may n...

• Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result in anaudio mute. Unlike AM/FM audible static, you will hear an audio mute when there isa satellite radio signal interference. Your radio display may display NOSIGNAL to i...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. Max A/C: Distributes recircu...

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED) 1. A/C control: Press to turn on the air conditioning. Press again toturn off the air conditioning. Usewith to improve cooling performance and efficiency. It engages automatically with the press of AUTO, , and MAX A/C. 2. (Recirculation c...

4. MAX A/C: Distributes recirculated air through theinstrument panel vents to cool thevehicle. This recooling of theinterior air is more economical and efficient. Recirculated air may alsohelp reduce undesirable odors from entering the vehicle. 5. DUAL: Press to turn on the separate passenger side t...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp Control(if equipped) The autolamp control sets theheadlamps to turn on and offautomatically. The autolamp control,located on the headlamp cont...

Push the headlamp control towards the instrument panel to deactivatethe foglamps. Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the ON position and • the headlamp control is in the or position • the transmission is not in park. Always remember to turn on your h...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel when exteriorlights are on. • Rotate the thumbwheel from leftto right to brighten theinstrument panel. • Rotate the thumbwheel from rightto left to dim the instrumentpanel. • Rotate to fully to the right (past detent) to turn o...

3. Turn on the low beam headlamps.The brightest part of the lightshould be below the horizontal line(4). If it is above the line theheadlamp will need to be adjusted. 4. Open the hood. 5. Locate the vertical adjuster foreach headlamp. Adjust the aim byturning the adjuster control eitherclockwise (to...

Cargo/reading lamps The dome portion of the lamp orthe center light can be turned onwhen the panel dimmer control isrotated past the detent or when adoor is opened. The rear dome lamp can be turnedON or OFF by sliding the control. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to eq...

3. Disconnect the electricalconnector. 4. Remove the old bulb by turningcounterclockwise and pull it out. Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb tobreak ...

Replacing tail/brake/turn/backup lamp bulbs 1. Turn the headlamp switch to OFFand open the tailgate. 2. Remove the two bolts from thelamp assembly. 3. Remove the lamp assembly. 4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly. 5. Pull the bulb straight out of thesocket. ...

Replacing license plate lamp bulbs The license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs: 1. Reach behind the rear bumper tolocate the bulb. 2. Twist the bulb socketcounterclockwise and carefully pullto remove it from the lampassembly. 3. Pull out the old b...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

Lift the lever back to its originalposition to lock the steering column. Never adjust the steeringcolumn when the vehicle is moving. ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamps. Slide on rod feature Rotate the visor towards the sidewindow and extend it rearward fo...

Storage compartment Press the latch to open the storagecompartment. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers: • Place the VELCRO 威 hook onto the side of the aftermarkettransmitter opposite of the...

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang any type of accessory oraccessory bracket from the plug. Improper use of the poweroutlet can cause damage ...

Truck bed auxiliary power point An additional auxiliary power pointis located in the bed of the truck(12V 20AMP max). Lift the cover to access the auxiliarypower point. CENTER CONSOLE 1. Cupholders 2. Tissue holder in lid 3. Rear power point 4. Large utility compartment has anexterior power point in...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up and hold the switch toclose. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise; thisnoi...

Power Down Back Window (if equipped) To operate the power down back window, the ignition switch must be inthe On or Accessory position (or with accessory delay power enabled). The power down back window only has three window position selections: • Fully open • Vent • Fully closed All rear seat occup...

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped withan inside rear view mirror with anauto-dimming function. Theelectrochromic day/night mirror willchange from the normal (highreflective) state to the non-glare(darkened) state when bright lights (glare) reach the...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previouslyset speed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased...

Press FAN + or - to adjust fanspeed. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up(from the closed position) to ventilate the vehicle. Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt thems...

Bounce back override: To override bounce back, within 2 seconds after reaching bounce back position, if the switch is held in the close positionthe moon roof will close with a 20–25 percent increase of closing forcebefore it will bounce back again. If the switch is released before themoon roof reach...

OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status. Thesyste...

Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/km. If you calculate your average fueleconomy by dividing miles traveledby gallons of fuel used (liters of fuelused by 100 kilometers traveled),your figure may be different...

System check Selecting this function from theSETUP MENU causes the messagecenter to cycle through each of thesystems being monitored. For eachof the monitored systems, themessage center will indicate eitheran OK message or a warningmessage for two seconds. Pressing the RESET control cycles the messa...

6. Press the RESET controlrepeatedly until the correct zonesetting for your geographic locationis displayed on the message center.The range of zone values are from01 to 15 and “wraps” back to 01. 7. Wait 4 seconds when correct zoneis chosen. Compass calibration adjustment. Perform compass calibratio...

This acts as a reminder that these warning conditions still exist withinthe vehicle. Warning display Status Door ajar Warning cannot be reset Check charging system Warning returns after 10 minutes Fuel level low Park brake engaged Check brake system Low tire pressure Warning returns only after the i...

Tailgate removal Your tailgate is removable to allowmore room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry thespring clip (on each connector) pastthe head of the support screw.Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45–degree anglefrom horizontal. 5....

To extend the cargo cage: 1. Lower tailgate. 2. Pull the lever on each side of thecargo cage to release it from thepickup box. 3. Lift the cargo cage over on to thetailgate. 4. Evenly push down on the cargocage and push the lever in on eachside locking it in place. To stow the cargo cage, follow ste...

1. To open, pull the release handlelocated on the inside of the pickupbox and lift the lid. 2. To close, lower the lid and pushdown until it clicks. Pickup box storage compartment The storage compartments are located inside the pickup box behind thewheel wells. 1. Turn latch counterclockwise tounloc...

LUGGAGE RACK Your vehicle is equipped with a roof rack. The maximum recommendedload is 100 lbs (44 kg), evenly distributed. If it is not possible todistribute the load, position it as far rearward as possible. Use the tiedown loops on the thumbwheels (if equipped) to secure the load. To adjust cross...

KEYS One key operates the door and tailgate locks and starts the vehicle. Thetonneau cover (if equipped) uses a unique key. Always carry a spare keywith you in case of an emergency. Your door and ignition keys are programmed to your vehicle; using anon-programmed key will not permit your vehicle to ...

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The typical operating range for your remote entry transmitter isapproximately 33 feet (10 meters). A decrease in operating range couldbe caused by: • weathe...

(refer to the Illuminated entry feature later in this section), if the control on the overhead lamp is not set to the off position and the perimeter alarm system (if equipped) will deactivate. Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlo...

How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of six) available before beginning this procedure. If all remote entry transmittersare not present during the programming procedure, the transmitters thatare not present during programming will no lo...

To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. Note: The driver’s door must be closed. You do not need to enter the keypad code first. Autolock The autolock feature will lock all the doors when: • all doors are closed, • the ignition is in the 3 (ON) position, • you shift into an...

2. Press the power door unlock control three times. 3. Turn the ignition from the 3 (ON) to the 1 (OFF/LOCK) position. 4. Press the power door unlock control three times. 5. Turn the ignition back to the 3 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. ...

Deactivating/activating autounlock Your vehicle comes with the autounlock feature activated. There are fourmethods to enable/disable this feature: • Through your authorized dealer, or • Performing the power door lock control procedure, or • Performing the keyless entry key pad (if equipped) procedur...

6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has beendisabled or a chirp followed by a honk to indicate the system has beenenabled. Message center procedure For information on activating/deactivating the autounlock feature usingthe vehicle’s message center (if eq...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position. The theft indicator will flash everytwo seconds when the vehicle isarmed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. • The theft in...

Please read and understand theentire procedure before you begin. 1. Insert the first previouslyprogrammed coded key into the ignition. 2. Turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON)position. Keep the ignition in the 3 (ON) position for at least threeseconds, but no more than 10 se...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. Pull l...

Press the control to recline theseatback forward or rearward. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control toadjust firmness. Press the other side of the controlto adjust softness. Heated seats (if eq...

REAR SEATS Folding down the 2nd row 60/40 seats Ensure that the head restraint is in the down position and no objectssuch as books, purses or briefcases are on the floor in front of thesecond row seats before folding them down. 1. Lower the head restraints bypulling on the strap. 2. Locate handle on...

because they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety belts or child safety seats and they move forward during pre-crashbraking. The most effective way to reduce the risk of unnecessaryinjuries is to make su...

Front safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occup...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an airbag supplemental restraint system (SR...

• This safety belt system has a retractor assembly that is designed toextend the safety belt webbing in a controlled manner. This helpsreduce the belt force acting on the user’s chest. BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly automatic locking retractor feature or any ...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Unbuckle the combination...

When the optional Safety Canopy 娂 system, seat-mounted side airbags, and/or the front airbags are activated, the safety belt pretensioners forthe driver and right front passenger seating positions will be activatedwhen the respective seatbelt is properly buckled. The driver and front passenger safet...

Second row comfort guide The second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the quarter trim paneland is used to adjust the comfort ofthe shoulder belt for smalleroccupants in the outboard secondrow seats. To adjust the comfort guide: 1. Slip the ...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then.....

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front safety belt buckleass...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Modifications to the front end of the vehicle, including frame,bumper, front end body structure and non-Ford tow hooks may effect the performance of the airbag sensors incr...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbags did notinflate in a collision does n...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects inthe front seat. • the system determines that an infant is present in a rear-facing infantseat that is installed according...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Airbag readiness secti...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Do not lean your head on the door. The Safety Canopy 娂 could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the Safety Canopy 娂 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your authorized d...

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again. The SafetyCanopy 娂 system (including the A, B and C pillar trim) must beinspected and serviced by anauthorized dealer. If the Safety Canopy 娂 is not replaced, the unrepaired area will increase therisk of injury ...

Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information ontransfer case operation and shiftingprocedures can be found in the Driving chapter. Information on transfer case maintenance can be foun...

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare(if equi...

If you are checking tire pressure when the tire is hot, (i.e. driven morethan 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires arehot from driving and it is normal for pressures to increase aboverecommended cold pressures. A hot tire at or below recommended coldinflation pressure co...

the tire and make necessary repairs. Also inspect the tire sidewalls forcracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced. For your safety,tires that are da...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance andlonger tire life. Unless otherwise specified, rotate the tires approximatelye...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Changing tires with TPMS Each road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby the tire and is not visibleunless the tire is removed. Thepressure sensor is locatedopposite (180 degrees) from thevalve stem. Care must be takenwhen...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

underinflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflation pressure. USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tire...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight – refer...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide . Loaded vehicles may handle differently than unlo...

Your vehicle is equipped with a standard Class II integrated hitch andrequires only a draw bar and ball with a 19 mm (3/4 inch) shankdiameter. An optional Class III/Class IV hitch is also available. Note: Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond...

4WD GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum GCWR-lb. (kg) Trailer weightrange-lb. (kg)(0-Maximum) 4.0L SOHC ClassII towing 3.73 8500 (3856) 0–3500 (0–1588) 4.6L* Class IItowing 3.55 8500 (3856) 0–3500 (0–1588) 4.0L SOHC ClassIII/IV towing 3.73 10000 (4536) 0...

Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer, and don’t make full throttlestarts. • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep gra...

equipped. Refer to the Maintenance and Specifications chapter for the lubricant specification. Remember that regardless of the rear axlelube used, do not tow a trailer for the first 500 miles (800 km) of anew vehicle, and that the first 500 miles (800 km) of towing be doneat no faster than 70 mph (1...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. This condition mayoccur when: • the front wheels are turned • a front wheel is against the curb 2. Turn the key to 4 (START...

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater) adapters. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be i...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

If the vehicle is stuck in snow or mud or when driving in deep sand,switching off the AdvanceTrac with RSC system may be beneficial so thewheels are allowed to spin. If your vehicle seems to lose engine powerwhile driving in deep sand or very deep snow, switching off theAdvanceTrac with RSC stabilit...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Transmission Control Strategy offers the optimaltransmission operation and shift quality. When the vehicle’s battery hasbeen disconnected for any type of ...

Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. Driving with a 6–speed automatic transmission (if equipped) This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Transm...

• Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Drive) only. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your...

• 4X4 LOW – momentarily illuminates when the vehicle isstarted. Illuminates when 4X4LOW (4WD Low) is selected. Using the Control Trac 4WD system 4X4 AUTO - Power to all four wheels; used for normal street and highway driving. 4X4 HIGH (4WD High) - Used for extra traction such as in snow or icy roads...

Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating characteristics that are somewhatdifferent from conventional vehicles, both on and off the road. How your vehicle differs from other vehicles Truck ...

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return to the pavement which could cause the vehicle to slidesideways out of control or roll over. Remember, your safety and thesafety of others should be yo...

• In the event of an emergency stop, avoid skidding the tires and do notattempt any sharp steering wheel movements. Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehi...

Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicle slowly while applying light pressure on the brake pedal. Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Eve...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the flasher...

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switc...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses 2A Grey Grey...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 28 10A Manual/DEATC climate control CB1 25A Windows The following relays are located on either side of the passengercompartment fuse panel. See your authorized dealer for service of theserelays. Fuse/Relay Location Desc...

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensor, refer to Changing tires with TPMS in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. The use of tire sealants may damage your tires. The use of tiresealants ...

• Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to im...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Tool Location Spare tire Under the vehicle, just in front ofthe rear bumper. Jack, lug nut wrench, jack handle, jack handle extension, wheel chock In the cab behind the passengerside ...

Removing the spare tire 1. Assemble the jack handle to thelug wrench by sliding the squareend of the jack handle through theplastic grommet on the lug nutwrench and into the square hole onthe other side. 2. Insert the square end of the jackhandle extension into the rearaccess hole located just above...

8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or los...

Stowing the jack and tools 1. Unblock the wheels. 2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or jack stowage compartment) so it will notbecome damaged. Re-install the wheel ornament onto the wheel once thetire is repaired or replaced. 3. Stow the ...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionv...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to the ground studlocated toward the front of the vehicle (forward of the battery) on theraidator support. Keep the negative (-) cable away from the battery ...

Do not connect the end of the second cable to the negative (-)terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump st...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The highpressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with...

4.0L SOHC V6 Engine 4.6L V8 Engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routin...

coatings, tree sap, or other organic contamination; these contaminantsmay cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned witha non-abrasive cleaner ...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material,...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine service. • Use only recommended fuels, lubricants, fluids and service partsconforming to specifications. • Your authorized dealer can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work ...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. 2007 07+ Explorer Sport Trac (esp) Owne...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine oil filler cap 2. Engine oil dipstick (out of view) 3. Brake fluid reservoir 4. Power distribution box 5. Battery 6. Power steering fluid reservoir 7. Radiator cap 8. Engine coolant reservoir 9. Air filter assembly 10. Wa...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2.Do not use any special washer fluid such as windshield water repellenttype fluid or bug wash. They...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

• 4.0L V6 engine • 4.6L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the lower and upper holes, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise thelevel within th...

• 4.0L V6 engine • 4.6L V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the...

5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil three clicks can be heard. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed. Engine Oil Recommendations 4.0L Engine Look for this cert...

4.6L Engine Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and fueleconomy requirements o...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Battery posts, terminals and related accessories contain lead andlead compounds. Wash hands after handling. Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is i...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservoir, when the engine is cool , until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam andscalding liqui...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium GoldEngine Coolant since a Ford-approved recycling process is not yetavailable. Used engine coolant should be disposed of in an appropriate manner. ...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cool...

Oil overheat can be triggered in severe driving conditions, such astowing heavy loads over mountainous terrain in extreme hottemperatures. As oil temperature increases, engine and vehicle speedwill be limited. The transmission will also shift differently. When the engine oil has cooled, the vehicle ...

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin contact could cause an adverse reaction. In sensitiveindividuals, serious personal injury or sickness may result. If fuel issplashed on the skin, prom...

Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/4 of a turn to unscrewthe cap. 3. Pull to remove the cap from the fuel filler pipe. 4. Reinstall the ca...

Many of the world’s automakers approved the World-wide Fuel Charter thatrecommends gasoline specifications to provide improved performance andemission control system protection for your vehicle. Gasolines that meet theWorld-wide Fuel Charter should be used when available. Ask your fuelsupplier about...

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still pres...

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to changea number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually gi...

2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter. These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedriving cycles withou...

Transmission fluid should be checked and, if required, fluidshould be added by an authorized dealer. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and result in damage to internal transmission component...

When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is r...

VEHICLE DIMENSIONS Dimensions Inches (mm) (1) Overall length 210.2 (5338.3) (2) Overall width 73.7 (1872.7) (3) Maximum height* 71.9 (1825.6) (4) Wheelbase 130.5 (3314.7) (5) Track width, front 60.9 (1547.5) (5) Track width, rear 62 (1574.3) * Height includes roof rack and cross bars with P235/65R18...

Vehicle identification number The vehicle identification number(VIN) is a 17 digit combination ofletters and numbers. The VIN isattached to a metal tag and islocated on the driver sideinstrument panel. The VIN numberis also found on the Certificationlabel. (Please note that in thegraphic XXXX is rep...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................56 AdvanceTrac ..............................198 Air cleaner filter ...............291–292 Air conditioning ..........................38 Airbag supplemental restraintsystem ................131–132, 140, 142 and child safety seats ............133description...