Ford 2007 Expedition v.2- Manuals

BREAKING-IN YOUR VEHICLE Your vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,600 km) ofnew vehicle operation. Vary your speed frequently in order to give themoving parts a chance to break in. Drive your new vehicle at least 50...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal...

Event Data Recording Other modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash event. Therecorded information may assist in the investigation of such an event.The modules may record information about both the vehicle and theoccupant...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type,failur...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Powertrain malfunction/reducedpower (RTT) (if equipped): Displays when the engine hasdefaulted to a ’li...

Low tire pressure warning(if equipped): Illuminates when your tire pressure is low. If the lightremains ON at start up or whiledriving, the tire pressure should bechecked. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to ON, the light will ...

Key-in-ignition warning chime (if equipped): Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and thedriver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedr...

Trip odometer: Registers the miles (kilometers) of individual journeys. • With Standard Message Center Press the RESET stem once toswitch from the odometer to thetrip odometer. Press the stem againto select Trip A and Trip B features.To reset the trip, press and hold thestem again until the trip rea...

AUDIO SYSTEMS Quick start — How to get going Listening to the radio 1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to adjust thevolume. Note: The system may take a few moments to turn on. 2. Press AM/FM repeatedly tochoose between AM/FM1/FM2frequency bands. 3. Press ...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

3. MENU: Press repeatedly to access the following settings: CATEGORY (satellite radio if equipped): Press MENU until the currently active category appears in the display (CATEGORY MODE). InCATEGORY MODE, press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc....

SINGLE PLAY / DUAL PLAY: If Single Play is ON, press / for Dual Play. For further information on Single Play/Dual Play, refer to Rear seat controls later in this chapter. FES (FULL/LOCKED): Your vehicle is equipped with a Family Entertainment DVD system. For further information on the DVD system,ref...

7. SHUFFLE: In CD/MP3 mode, press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, press SEEKto begin random play. Otherwise, random play will begin when thecurrent track is finished playing. CD SHUF will appear in the display. Todis...

13. TEXT/SCAN: In radio and CD/MP3 mode, press and hold for a brief sampling of radio stations orCD tracks. Press again to stop. In CD/MP3 mode, press and release to display track title, artist name, and disc title. In TEXT MODE sometimes the display requires additional text to be displayed. When th...

COMPRESS (Compression): Available only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display. Use / / SEEK, SEEK to toggle ON/OFF. When COMPRESS is ON, the system will bring soft and loud CD passages together for a moreconsistent listening level. Single Play/Dual Play: If Single Pl...

17. LOAD: To load a disc into the system, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, label side up.If you do not choose a slot within 5 seconds, the system will choose foryou. Once loaded, the first track will begin to play. To aut...

Using headphones/Dual Play mode Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. Plug a 3.5 mm headphone (not inc...

• Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstorms can interfere with your reception. • Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed. CD/CD p...

• MP3 folder mode represents a folder structure consisting of one levelof folders. The CD player numbers all MP3 tracks on the disc (notedby the .mp3 file extension) and all folders containing MP3 files, fromF001 (folder) T001 (track) to F253 T255. • Creating discs with only one level of folders wil...

roof of your vehicle. The vehicle roof provides the best location for anunobstructed, open view of the sky, a requirement of a satellite radiosystem. Like AM/FM, there are several factors that can affect satelliteradio reception performance: • Antenna obstructions: For optimal reception performance,...

Quick start Your Family Entertainment System includes a DVD system, two sets ofwireless infrared (IR) headphones and a wireless infrared (IR) remotecontrol. To play a DVD in the DVD system: The DVD system can play DVD-Video, DVD-R, DVD-R/W discs as well asaudio CDs and video CDs. To ensure proper di...

DVD player controls 1. Headphone control A/B: Press to select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for that headset. When aheadphone channel has been selected (A or B), selections will affect thesource on that channel only. Note: Headphone A can acces...

11. / (Headphones/Speakers): Press once for Dual Play (Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing through all speakers). For furtherinteraction information, refer to Single Play/Dual play. 12. MEDIA: Press repeatedly to select from the various pos...

1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controlsdecrease and increase the display brightness. 3. DISPLAY: Press to access the ...

22. ENTER: Press to select the highlighted menu option. 23. ILLUMINATION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails to...

Headphones Wireless headphones Your FES system is equipped with two sets of battery powered, infraredwireless headphones. Two AAA batteries are needed to operate theheadphones. (Batteries are included.) Additional infrared wireless headphones may be purchased for use withthe system. Also, wired head...

Channel A source. The wired headphone jack for Channel B is located onthe right side of the FES and is labeled B. Headphones plugged into this headphone jack will hear audio from the audio source selected to bethe Channel B source. Adjust the headphone volume usingthe volume control on the DVDsystem...

Audio displays Your DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. Somepossible radio display messages: • SINGLE PLAY or DUAL PLAY • DVD LOAD • DVD MENU • DVD STOP Audio interaction You can then also use the front aud...

When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Play mode, allspeakers listen to the same media. In Dual Play mode, rear seatpassengers can use the infrared wireless, or wired (not included)headphones...

The front glass on the liquid crystal display (LCD) flip-downscreen may break when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contactwith skin, wash immediately with soap and water. The driver should not attempt to operate any function of t...

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to consult the dealer or anexperienced ra...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Distributes recircu...

4. REAR Rear temperature control: Press to enable the auxiliary system and to set the desired rear cabin airflow temperaturewith the front control. The rear cabin airflow temperature will match thedriver airflow temperature setting when only the center rear temperaturelight ( REAR ) is illuminated. ...

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instru...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan speed to the highest setting.5. Direct the outer instrument panel vents towards the side windows.To increase airflow to the outer instrument panel...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp contro...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignitio...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Move the control to the full downposition, past detent, t...

4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge towards theright. If this edge is not at thehorizontal reference line, the beam will need to be adjusted so the edgeis at the same height as the horizontal reference line. 5. Locate the vertical adjuster oneach h...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • the remote entry controls arepressed and the ig...

Rear cargo lamp The dome lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is OFF(and switch is in the middleposition). With the i...

Function Number of bulbs Trade number Headlamps (low andhigh-beam) 2 H13/9008 Front sidemarker 2 194 Front park/turn lamps 2 3157 A Foglamps 2 9145 Front row map lamps 2 W5W Front row map/domelamps 3 578 Rear cargo lamp 1 578 2nd row reading lamp 2 W5W Turn/tail/brake/sidemarkerlamps 2 3157K or 4157...

3. At the back of the headlamp,remove the two headlamp assemblyretainer bolts. 4. Slide headlamp assembly forwardand off the retaining tab to exposethe back of the headlamp assembly. 5. Rotate the bulb socketcounterclockwise and remove fromthe lamp assembly. 6. Carefully pull the bulb out of thesock...

6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing thelamp assembly with two torx screws. High-mount brakelamp To change the high-mountbrakelamp bulbs: 1. Remove the two screws holdingthe lamp assembly in pla...

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch isin the OFF position. 2. Remove the license lamp screwfrom the assembly. 3. Pull the lamp down and twist th...

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors areclosed and the interior lights haveautomatically turned off or theopposite mirror approach lamp hasturned off. 2. With a small flat tippedscrewdriver, insert the tip into theapproach light module slot lo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to either position. From either position, the control will automatically return to the INT 2or OFF position. TILT STEERING WHEEL 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering up or do...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Forward storage bin (if equipped) The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The ...

Cupholder/Ashtray (if equipped) The cupholder/ashtray is located onthe instrument panel. To open cupholder/ashtray, push inon the door and release. The doorwill spring out 1/4+ inches. Thenpull cupholder/ashtray assembly outthe remaining distance to utilize. Toclose, push assembly in completelyand r...

Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorperformance. Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products. EXTERIOR MIRRORS Power side view mirrors The ignition c...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control toadjust accelerator and brake pedal. • Press the top of the control toadjust the pedals ...

• Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate controlfeatures. Audio control features Press MEDIA to selec...

The moon roof has a built-in sliding shade that can be manually openedor closed when the glass panel is shut. To close the shade, pull it towardthe front of the vehicle. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a ...

Note: There are 30 seconds in which to initiate Step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped de...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status preceded...

3. Locate the reset button on top ofthe compass sensor mounted behindthe mirror. 4. Press and hold the reset buttonon the compass module forapproximately 4 seconds until themessage center displays a selectionto change the current zone setting:ZONE <XX> RESET = CHANGE 5. Press and release the R...

5. The compass is now calibrated. Setup menu This menu allows the user, via the RESET stem located in theinstrument cluster, to interface and control the information displayed inthe message center for following selectable features: • System Check • Oil life • Units (English/Metric) • Autolamp • Auto...

OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status preceded...

Warning display Status For 4x4 low stop vehicle(if equipped) Temporary alert For 4x4 apply brake(if equipped) For 4x4 shift to N(if equipped) To exit 4x4 low stop vehicle(if equipped) To exit 4x4 apply brake(if equipped) To exit 4x4 shift to N(if equipped) DRIVER DOOR AJAR. Displayed when the driver...

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in...

Keep keys out of reach of children. Do not allow children to playnear an open or moving power liftgate. Do not open the liftgate in a garage or other enclosed area with a lowceiling. If the liftgate is raised the liftgate could be damaged against alow ceiling. To open the liftgate from theInstrument...

To close the liftgate with therear cargo area control button: Press and release the control on theleft rear quarter panel to close theliftgate. The chime will beep once ifconditions are not correct to startan operation (i.e., the vehicle is outof park). In a normal close, thechime will begin just be...

MANUAL LIFTGATE (IF EQUIPPED) • To open the liftgate, position yourhand on top of the liftgate handleand pull to open the liftgate. • Do not open the liftgate orliftgate glass in a garage or otherenclosed area with a low ceiling.If the liftgate glass is raised andthe liftgate is also opened, bothlif...

Cargo shelf/divider (if equipped) The cargo shelf/divider is located behind the rear seat of your vehicle.The shelf has two positions: Flat shelf which pivots up and snaps intoplace OR a divider which pivots up and snaps vertically into place. Donot put more than 30 lbs. (14 kg) on the shelf. To mov...

LUGGAGE RACK Your vehicle is equipped with a roofrack for transporting items on theexterior of the vehicle. Themaximum recommended load to becarried on the roof rack is 200 lbs(90 kg), evenly distributed. Thecross-bars can be adjusted by usingthe thumbwheels at each end. Usethe tie-down loops on the...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

• the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON)position and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivatin...

Keyless entry key pad procedure 1. Turn the ignition to the 1 (OFF/LOCK) position. 2. Close all doors, the liftgate and liftgate window. 3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should recei...

The remote entry system allows you to lock or unlock all vehicle doorsand liftgate and open the liftgate window without a key. The remote entry lock/unlock feature operates in any ignition position.The liftgate glass features operate as long as vehicle speed is less than5 mph (8 km/h). The panic fea...

To confirm all doors are closed and locked, press the control a secondtime within three seconds; the park/turn signal lamps will flash once andthe horn will chirp. • 4–button remote • 5–button remote If any of the doors or liftgate are ajar, the horn will make two quickchirps, reminding you to prope...

• 4–button remote • 5–button remote To deactivate the alarm, press the control again or turn the ignition tothe 2 (ACCESSORY) or 3 (ON) position. Memory feature The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the controlwill a...

• 5–button remote Activating the memory feature To activate this feature: 1. Position the seat, rearview mirror, and adjustable pedals to thepositions you desire. 2. Press the SET control on the driver’s seat. 3. Within 5 five seconds, press one control on the remote transmitter andthen press the 1 ...

Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. Ifall remote entry transmitters are not present during the programmingprocedure, the transmitters that are not present during pr...

Perimeter lamps illuminated entry The following items will illuminate when the (unlock) control on the remote entry transmitter is pressed: • Head lamps • Park lamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the (lock) contro...

• When the ignition is in the 3 (ON) position, the indicator will glow for3 seconds to indicate normal system functionality. If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. Ifthis occurs, the vehicle sho...

SEATING Front row adjustable head restraints Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of these head restraints is to help limit headmotion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is loca...

Lift handle to move seat forward orbackward. Manual seat recliner (if equipped) Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in t...

Using the armrest (if equipped) Push the release control to movethe armrest up or down. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseat. Turn the lumbar support controlclockwise for more support. Turn the lumbar supportcounter-clockw...

Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Press the control to recline theseatback forward or rearward. Note: On vehicles with memory seats, to pre...

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat, powermirrors, and adjustable pedals totwo programmable positions. The memory seat control is locatedon the outboard side of the seatcushion. • To program position 1, move thedriver ...

1. Lower the head restraints bypulling on the strap. 2. Locate handle on the side of theseat cushion by the door. 3. Pull up on the handle and pushthe seatback forward toward thefront of the vehicle. To return the seat to the upright position: 1. Lift the seatback toward the rearof the vehicle. 2. R...

2. Pull the handle up again until theseat releases from the floor. 3. Push the seat upward and fold itaway from the third row. Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injury during a sudden stop. To return the seat to a sea...

Exiting the 3rd row 1. Pull the strap located at thebottom outboard of the seat back torelease the seat from the floor, androtate the seat up towards the frontseat. 2. Follow the directions above toreturn the seat from the E-Z entryand to the upright position. Reclining the 2nd row outboard 40% seat...

To prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled when moving the seat to the load floor position. 2. With the latch released theseatback can be lowered into theload floor position. 3. To return the seat to the uprightposition, lift the seatback unti...

Adjusting the 2nd row center 20% seat (if equipped) Lift the handle to move the seatforward or backward. Note: This seat can be moved forward to keep a child in a childrestraint close to the front seat occupants. The seat should bemoved to the full rearward position when it is occupied by olderchild...

Pull up on the handle locatedbehind the seatback while pushingthe seatback forward and down intothe seat cushion. To return the seatback to its original position lift the seatback until itlatches into place. Before returning the seatback to its original position, make surethat cargo or any objects a...

Push the bottom portion of thecontrol button to lower the desiredseatback. Push the top of the control buttonto return the seatback to its originalposition. The power fold down seats will operate for 10 minutes after theignition switch is in Off. The transmission must be in P (park),and the liftgate...

• The warning light will either flash or stay lit. • The warning light will not illuminate immediately after the ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, eve...

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm. 2)Never swing the safety belt around your n...

• Front and rear seats All safety restraints in the vehicle are combination lap and shoulder beltsexcept for the front row center lap belt (if equipped). Front center lap belt To fasten the front center lap belt,insert the tongue into the centerbuckle until you hear a snap andfeel it latch. Make sur...

When to use the automatic locking mode • Anytime a child safety seat (except a booster) is installed in the vehicle. Children 12 years old and under should be properly restrainedin the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this cha...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, allsafety belts should be checked for proper function. Failure to replacethe belt and retractor assembly could incre...

squeeze the side release buttons and slide the height adjuster up. Pulldown on the height adjuster to make sure it is locked in place. Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effec...

Position the safety belt comfort guide so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt andincrease the risk of injury in a collision. Safety belt extension assembly If the safety belt is too short ...

If... Then... The driver’s safety belt is notbuckled approximately 5seconds after the safety beltwarning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warning lightilluminates and the warning chimesounds for 6 seconds every 30seconds, repeating for approximately5 m...

Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bag system One time disable Any time the safety belt is buckled and then unbuckled during anignition ON cycle, Belt-Mi...

4. Within approximately 7 seconds of the light turning off, buckle thenunbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light willflash 4 times per second for 3 seconds. • This will ...

Additional equipment may affect the performance of the airbagsensors increasing the risk of injury. Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating positi...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is ...

How does the side airbag system work? The design and development of the side airbag system includedrecommended testing procedures that were developed by a group ofautomotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofin...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with the syst...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

Move a child to a different seating location if the shoulder beltdoes not stay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of thebooster seat. Never put the shoulder belt under a child’s arm or behind theback because it eliminates the protection for th...

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a suddenstop or collision. Installing child safety seats with combination lap and shoulderbelts Airbags ca...

Installing child safety seats in the center front seating position(if equipped) Always transport children 12 years old and under in the rearseats and always properly use appropriate child restraints. It is safer to install child safety seats in seating positions thathave child seat anchors. The fron...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attached somewhere other than the correct t...

6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired. At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflatea...

of 1 psi (7 kPa) in inflation pressure. Check your tire pressuresfrequently and adjust them to the proper pressure which can be foundon the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivi...

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls forcracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystan...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Changing tires with TPMS Each road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby the tire and is not visibleunless the tire is removed. Thepressure sensor is locatedopposite (180 degrees) from thevalve stem. Care must be takenwhen...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecommended inflation pressure. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires o...

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Label or Safety Compliance Certification Label: Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard e...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

cement to your home? If you and your friend each weigh 220 lb.(99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 -440 - 1200 = - 240 lb. No, you do not have enough cargo capacity tocarry that much weight. In metric units, the calculation would be: 635 kg-(2 x 99 kg) - (12 x 45 k...

Engine Rear axle ratio Maximum GCWR - lb. (kg) Trailer weight range (0 - maximum) lb. (kg) Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x2 5.4L with standard trailer tow package All 12200 (5534) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–9000 (0–4082) Expedi...

3. Measure the height of a reference point on the front and rear bumpersat the center of the vehicle. 4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within a 1 ⁄ 2 ” (13 mm) of the reference point. After proper adjustment, the rear bumper shoul...

Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer, and don’t make full throttlestarts. • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep gra...

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maintenance and Specifications chapter for the lubricant specification. Rememb...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsil...

4. Make sure the parking brake isset. 5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you ...

3. After idling for a few seconds, apply the brake, shift into gear anddrive. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine stillfails to start, press the accelerator to the floor and try again; this willall...

results, plug the heater in at least three hours before starting the vehicle(the heater can be plugged in the night before starting the vehicle). Toplug the heater in, remove the cap from the plug and insert the plug intoa 110 volt grounded outlet. Be sure to re-attach the cap onto the plugwhen the ...

mechanical noise may be heard during this test. This is normal. If amalfunction is found, the ABS warning light will come on. If the vehiclehas continuous vibration or shudder in the steering wheel while braking,the vehicle should be inspected by an authorized dealer. The ABS operates by detecting t...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

• Driving on slick surfaces. • Cornering while towing a heavily loaded trailer (refer to Trailer towing in the Tires, Wheels and Loading chapter.) Roll Stability Control 娂 (RSC) The RSC system works in conjunction with the AdvanceTrac 威 system to help maintain roll stability of the vehicle during ag...

Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a AdvanceTrac 威 with RSC event is an indication that at least some of the tires haveexceeded their ability to grip the road; this...

• High crosswinds • Wheels out of alignment • Loose or worn suspension components Variable assist steering Your vehicle is equipped with variable assist power steering. At lowengine RPM, steering assist will adjust to reduce efforts and improve lowspeed maneuverability. At high engine RPM, the assis...

LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, thelimited slip axle functions like a standard rear axle.Extended use of other than the manufacturer’s specified size tires on al...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your authorized dealer. Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever f...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working proper...

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normal detection zone of the reverse sensing system may create false beeps. The system will assist the driver in detecting certain objects while thevehicle moves in reverse at speeds less t...

Audible Warnings Distance to Object Warning 5.7 feet (1.8 meters) to 9 feet(2.8 meters) Medium beep 9 feet (2.8 meters) to 13 feet(4 meters) Medium/slow beep 13 feet (4 meters) to 19.6 feet(6 meters) Slow beep Speed below 2.5 mph (4 km/h) up to 1.4 feet (.4 meters) Solid 1.4 feet (.4 meters) to 3 fe...

CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW)is selected while the vehicle is moving, the system...

Positions of the Control Trac system The Control Trac system functionsin four modes: • 2H (2WD) delivers power to the rear wheels only. This isappropriate for normal on-roaddriving on dry pavement. • 4A (4X4 AUTO) provides electronic control four-wheeldrive with power delivered to allfour wheels, as...

Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily underoff-road conditions. Avoid sharp turns or abrupt maneuvers in thesevehicles. Note: The Control Trac selector knob s...

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return to the pavement which could cause the vehicle to slidesideways out of control or roll over. Remember, your safety and thesafety of others should be yo...

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more...

If the transmission, transfer case, front axle or rear axle are submergedin water, their fluids should be checked and changed, if necessary. Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced. After driving th...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in...

Note: With extended use, the flasher may run down your battery. FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start,...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accessto the fuse box, pull the paneltoward you and swing it out awayfrom the side and remove it. Toreinstall it, line up the tabs with thegrooves on the panel, t...

Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery sectio...

Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longerfunction. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increasedr...

• Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle beoperated in 4WD modes with a temporary emergency spare tire. If 4WDoperation is necessary, do not ...

Stopping and securing the vehicle 1. Park on a level surface, activatethe hazard flashers and set theparking brake. 2. Place the gearshift in P (Park)and turn the engine OFF. Spare tire information Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in ...

Tire change procedure To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block the wheels (both front or both rear) on the opposite end of the vehicle from the wheelbeing changed. If on a grade, block both opposite wheels on thedownward side of the ...

Stowing the spare tire 1. Lay the tire on the ground, near the rear of the vehicle, with the valvestem side facing up. 2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Ifequipped, you may have to removethe wheel center cap prior topushing the retainer t...

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on b...

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, behind thebattery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-)term...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the jump starting stud. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + – + – 2007 Expedition (exd) Owners Guide (po...

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – 2007 Expedition (exd) Owners Guid...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist ...

• To remove tar and grease, use Motorcraft Bug and Tar Remover(ZC-42), available from your authorized dealer. ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engi...

• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the ca...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect perform...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. 2007 Expediti...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 3V–V8 engine 1. Windshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap 9. Battery 2...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the blade dow...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and e...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the indicator back in an...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the bat...

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “COLD FILL RANGE” or the “FULL COLD” lev...

Severe climates If you drive in extremely cold climates (less than –34°F [–36°C ]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection cha...

• The symbol will illuminate. • The indicator light will illuminate. If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder operation. Each disabledcylinder acts as an air pump and cools the engine. When this occurs the vehicle will sti...

Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcraft fuel filter is not used. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in a...

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel conta...

Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unleaded gasoline is not recommended for vehicles designed to use“Regular” unleaded gasoline because it may cause these problems tobecome more pronounced...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a...

The EPA window sticker should be your guide for the fuel economycomparisons with other vehicles. It is important to note the box in the lower left corner of the windowsticker. These numbers represent the range of fuel economy expected onthe vehicle under optimum conditions. Your fuel economy may var...

OBD-II may not have symptoms that are apparent, continued drivingwith the indicator on can result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and lead to morecostly repairs. Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and result in damage to internal transmission components. AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing t...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A ABS (see Brakes) .....................255 Accessory delay ........................101 AdvanceTrac ..............................258 Air cleaner filter ...............355, 358 Air suspension ...........................263 description ..............................263 Airbag supplemental restraintsy...

change oil soon warning,message center .......................332checking and adding ..............332dipstick ....................................332filter, specifications ........334, 358recommendations ...................334refill capacities ........................359specifications ................

P Panic alarm feature, remoteentry system ..............................149 Parking brake ............................257 Parts (see Motorcraft parts) ....358 Pedals (see Power adjustablefoot pedals) ...............................104 Power adjustable foot pedals ...104 Power distribution box(see Fu...