Ford 2007 Escape v.2- Manuals

Remember to pass on this Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle. Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g....

Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag. Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with thi...

Anti-lock brake system: Illuminates indicating an ABS fault.If the lamp stays on for more than afew seconds, then an ABS fault isindicated, have the system servicedimmediately by your authorized dealer. Normal braking is still functionalunless the brake warning light also is illuminated. Airbag read...

With message center Overdrive off (automatictransmission): Illuminates when the overdrive function of thetransmission has been turned off.Refer to the Driving chapter for transmission function and operation. If the light flashes steadily, have the system serviced immediately, ordamage to the transmi...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3Radio (if equipped) 2007 Escape (204) Owners Guide (post-2002-fmt)USA (fus) Entertainment Systems 19

stations are independently operated and individually elect to use RDStechnology to transmit station ID and program type as desired. Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it isbroadcasting RDS data)....

Setting the clock: Press MENU until SELECT HOUR or SELECT MINS is displayed. Use SEL to manually increase ( ) or decrease ( ) the hours/minutes. Press MENU again to disengage clock mode. Folder/Track Mode: In MP3 mode, press MENU until MODE appears in the display. Use SEL to toggle between FOLDER (o...

For information regarding SIRIUS Satellite Radio, please call toll-free888-539-SIRIUS (888-539-7474) or visit the SIRIUS website atwww.siriusradio.com 24. CD slot: Insert a CD, label side up. AM/FM stereo in-dash six CD modular audio (if equipped) 1. CD: To begin CD play, press LOAD. When the system...

19. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. 20. CD: Press to enter CD mode. CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re-recordable compactdiscs may not fu...

instructions are included with the dealer installed kit. Check with your authorized dealer for availability. 20. Seek: Press and release SEEK / for previous/next strong station, tape selection or CD track. 21. BAND: Press to toggle through AM/FM1/FM2 frequency bands. 22. Cassette door: Insert the ca...

• Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, extreme hu...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. : Distributes outside air through the instrument panel ...

• Under normal weather conditions, do not leave the air flow selector inMAX A/C or O (OFF) when the vehicle is parked. This allows thevehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with theairflow to the back seats. • Remove any...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to also turn on the headlamps. Headlamp battery saver The battery saver will shut off the exterior lamps 10 minutes after theignition switch has been turned off if the headlam...

Autolamp delay system (if equipped) If your vehicle has an autolamp delay feature, you can set the delay timeto keep the headlights on for up to three minutes after the key is turnedOFF. The delay time is set to 20 seconds at the factory, but the delaytime may be changed by following the steps below...

Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the ignition must be in the 3 (RUN) position. • the headlamp control must be in the OFF, parking lamps or autola...

Foglamp control (if equipped) Press the foglamp control, locatedon the instrument panel, to activatethe foglamps. The foglamp indicatorwill illuminate when the foglampsare on. Press the foglamp control todeactivate the foglamps. The foglamps will only operate withthe parking lamps or headlamps on.Wh...

• (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from thecenter of your headlamp to theground and mark an 8 foot (2.4meter) horizontal reference line onthe vertical wall or screen at thisheight (a piece of...

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America and an“E” for Europe to ensure lamp performance, light brightness and patternand safe visibility. The correct bulbs will not damage the lamp assemblyor...

Replacing brake/tail/turn/backup lamp bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lampassembly, one just below the other. Follow the same steps to replaceeither bulb: 1. Make sure the headlamp switch isin the OFF position and then openthe liftgate to expose the lampassemblies...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control down twopositions from OFF. For high speed wiper operation,move control down three positionsfr...

Rear window wiper/washer controls For intermittent operation of rearwiper, rotate end of control upwardto the position. For normal speed rear wiperoperation, rotate control upward toON. To activate the rear washer, rotatethe control to the position and release. TILT STEERING WHEEL To adjust the stee...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamps. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment (if equipped) Press the release on the door toopen the storag...

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang any type of accessory oraccessory bracket from the plug. Improper use of the poweroutlet can cause damage ...

Press and hold the bottom part ofthe rocker switch to open thewindow. Press and hold the top partof the rocker switch to close thewindow. Note: The window switches will not illuminate when the window lockcontrol is in the LOCKED position. Rear Window Buffeting: When one or both of the rear windows a...

AUTOMATIC DIMMING REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped withan inside rear view mirror which hasan auto-dimming function. Theelectronic day/night mirror willchange from the normal (highreflective) state to the non-glare(darkened) state when bright lights (glare) reach the mirro...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status preceded by a brie...

Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km. If you calculate your average fueleconomy by dividing gallons of fuel used by 100 miles traveled(kilometers traveled by liters used), your figure may be different th...

LIFTGATE To open the rear window, pull theright side of the liftgate handle. To open the liftgate, pull the leftside of the liftgate handle. • Do not open the liftgate orliftgate glass in a garage or otherenclosed area with a low ceiling.If the liftgate glass is raised andthe liftgate is also opened...

Ensure that the posts are properly latched in mounting features.The cover may cause injury in a sudden stop or accident if it is not securely installed. Do not place any objects on the cargo area shade. They mayobstruct your vision or strike occupants of vehicle in the case of a sudden stop or colli...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

7. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position.The horn will chirp one time to confirm the programming mode has beenexited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking Two step door unlocking 1. Turn the key in the door cylinder to unlock t...

Relock This feature will also automatically relock all the doors when: • the ignition is in the 3 (RUN) position and any door is opened thenclosed, and • you put the vehicle in motion by releasing the brake pedal. Deactivating/activating the autolock feature The autolock feature can be turned on or ...

CHILDPROOF DOOR LOCKS • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for each door. Setting the lock for one...

• other vehicles parked next to your vehicle, or • weak or dead transmitter battery. The remote entry system allows youto lock or unlock all vehicle doorswithout a key. The remote lockingand unlocking features will operateindependent of the ignition position;however, the panic feature will onlyopera...

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash onceand the perimeter alarm (if equipped) will start the arming process. Formore information concerning the perimeter alarm, refer to Perimete...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

Note: Ensure the brake pedal is not depressed during this sequence. To reprogram the remote entrytransmitters: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK)position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) betwe...

program your spare keys to your vehicle or you can program the keysyourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems mayre...

• the park/turn lamps will not flash if the hood, any door or the liftgate are open. Once all doors, hood and liftgate are closed, the park/turnlamps will flash to confirm the alarm will be set. When the vehicle is locked, the alarm is set after a 20–second armingperiod. When you press the control o...

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatbac...

Push side control and push down onhead restraint to lower it. Adjusting the front manual seat (if equipped) Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. 2007 Escape (204) Owners Guide (post-2002-fmt)USA (fus) Seating and Safety Restraints 90

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

2. Place the head restraint underthe front seat for storage. 3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. 2007 Escape (204) Owners Guide (post-2002-fmt)USA (fus) Seating and Safety Restraints 94

Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the seat back foldingpath. 5. To release seatback, pull theseatback release lever (on top ofseat) toward the front seat. This iscommon for both 60% and 40...

Returning the rear seats to upright position 1. Pull seatback up and into uprightposition making sure seatback locksinto place and the red seatunlatched indicator on releasepaddle is not visible. 2. Rotate seat cushion down into theseating position making sure thatthe seat cushion is locked into pla...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

longitudinal deceleration. The pretensioners are designed to activate infrontal, and in side collisions and rollovers when the vehicle is equippedwith the Safety Canopy 娂 system. Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the ...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments w...

Determining if the Personal Safety System 姟 is operational The Personal Safety System 娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Referto the Warning light section in the Instrument Cluster chapter. Routine maintenance of the Personal S...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. Energy Management Feature • This vehicle has a safety belt system with an energy managementfeature at the front outboard seating positions to help further reducethe risk of injury in the event of a head-on collision. • The ...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checkedby an authorized dealer. Failure to replace the Belt and Retractorassembly could increase the risk of injury in collis...

Failure to replace the safety belt assembly under the aboveconditions could result in severe personal injuries in the event of a collision. Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can be added (...

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned t...

If... Then... The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minuteshave elapsed since the ignitionswitch has been turned ON... The BeltMinder 威 feature will not activate. The driver’s or front passenger’ssafety belt i...

One time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the BeltMinder 威 is disabled for the current ignition cycle. The BeltMinder 威 feature will enable during the same ignition cycle if the occupant buckles and remains buc...

3. For the seating position being disabled, buckle then unbuckle thesafety belt 9 times, ending in the unbuckled state. (Step 3 must becompleted within 50 seconds after the safety belt warning light turnsoff.) • After Step 3, the restraint system warning light (airbag light) will beturned on for thr...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Modifications to the front end of the vehicle, including frame,bumper, front end body structure, tow hooks and B-pillar surrounding parts may affect the performance of the ...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the airbag sensors to closean electrical circuit that initiatesairbag inflation. The fact that theairbags did not inflate in a collisi...

• seat-mounted side airbags (if equipped). Refer to Seat-mounted side airbag system later in this chapter • Safety Canopy 娂 system (if equipped). Refer to Safety Canopy 娂 system later in this chapter. • one or more impact and safing sensors. • Safety belt pretensioners • a readiness light and tone. ...

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects inthe front seat, • the system determines that an infant is present in a rear-facing infantseat that is installed according...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the status of the system. Refer to Airbag readiness section ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot function properly in the ev...

If the shoulder belt portion of a combination lap and shoulder belt canbe positioned so it does not cross or rest in front of the child’s face orneck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit. Do not...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter. Carefully f...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. Information ontransfer case operation and shiftingprocedures can be found in the Driving chapter . Information on transfer case maintenance can befound in the Maintenance and Specification chapter . You should become ...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Age Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.) the tires experience throughout their lives.In general, tires should be replaced after six years regardless of treadwear. However, heat caused by ho...

The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Companymay affect the operation of your Tire Pressure Monitoring System. If the TPMS indicator is flashing...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Changing tires with TPMS Each road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby the tire and is not visibleunless the tire is removed. Thepressure sensor is locatedopposite (180 degrees) from thevalve stem. Care must be takenwhen...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

tires are flat, repair as necessary. Check air pressure in the road tires. Ifany tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecommended inflation pressure. USING SNOW TIRES AND TRACTION DEVICES Snow tire...

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Label or Safety Compliance Certification Label: Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard e...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

cement to your home? If you and your friend each weigh 220 lb. (99 kg),the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440 –1200 = – 240 lb. No, you do not have enough cargo capacity to carry thatmuch weight. In metric units, the calculation would be: 635 kg – (2 x 99kg) – (12 x 45 ...

• Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to thesevere duty schedule in the scheduled maintenance guide. • Do not tow a trailer until your vehicle has been driven at least ...

4x4 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - lb. (kg) Trailer Weight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m) 2 2.3L w/manual transmission 5040 (2286) 1500 (680) 24 (2.2) 2.3L w/automatic transmission 5100 (2313) 1500 (680 ) 24 (2.2) 3.0L w/automat...

Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to hook retainers on thevehicle. To connec...

• Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. (For additional information, refer to Understanding the gearshift positions of the 4–speed automatictransmission in the Drivin...

Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after thetrailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise abo...

STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand steering column and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. RUN, all electrical circuitsoperational and warning lights willilluminate. Thi...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. Always...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the RUN position unless brake pedal is depressed. If you cannot move the gearshift...

5. Start the vehicle and release the parking brake. Do not drive your vehicle until you verify that the brakelampsare working. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehic...

MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch The manual transaxle has a starter interlock that prevents cranking theengine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the ...

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts during light to moderate accelerations and cruises (for best fuel economy) Shift from: 1-2 10 mph (16 km/h) 2-3 20 mph (32 km/h) 3-4 32 mph (52 km/h) 4-5 37 mph (60 km/h) Reverse Make sure that your ve...

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse) is selected and thevehicle is moving at speeds less than 3 mph (5 km/h). The system is noteffective at speeds above 3 mph (5 km/h) and may not dete...

FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. Your vehicle is equipped with an intelligent 4WD System thatcontinuously monitors vehicle conditions and automatically adjusts t...

Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating characteristics that are somewhatdifferent from conventional vehicles, both on and off the road. How your vehicle differs from other vehicles Truck ...

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return to the pavement which could cause the vehicle to slidesideways out of control or roll over. Remember, your safety and thesafety of others should be yo...

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy off-...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for th...

• emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in the glove compartment. In Canada,...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. This switch is located in the frontpassenger’s footwell, beh...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A* Trailer tow park lamps 2 — Not used 3 15A* Front and rear park lamps 4 10A* Ignition switch 5 2A* Powertrain Control Module (PCMrelay), Fuel pump relay, Main fanrelay, High/Low spe...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 33 15A* Air bag module, Passenger Air bagDeactivation (PAD) indicatorlamp, Occupant ClassificationSensor (OCS) 34 5A* ABS module, Evac and Fill, Speedcontrol 35 5A* Heated seats module, 4WD * Mini fuse ** Cartridge fuse...

Your vehicle may be equipped with a conventional spare tire that isdifferent in one or more of the following: type, brand, size, speed ratingand tread design. If this is the case, this dissimilar spare tire is still ratedfor your vehicle loads (GAWR and GVWR). This temporary spare tire isnot equippe...

• Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to im...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through theaccess hole in the rear bumper. 2. Turn the handle counterclockwiseand lower the spare tire until it canbe sl...

5. Use the lug wrench to remove thelug nut from the spare tire tether. 6. If not replacing the spare or flattire to the underbody storage area,raise winch up into the installedposition. 7. Use the attached Velcro strap (2)to tie the tether end to the winchactuator shaft (if equipped). Changing the f...

Before placing the jack under the vehicle, NOTE the jack locations: • Front • Rear 2007 Escape (204) Owners Guide (post-2002-fmt)USA (fus) Roadside Emergencies 213

Cargo management system (ifequipped): Reclip the tools onto the jack. Reinstall the jack and tools in the cargo area. To replace the jack in thevehicle, • guide the jack bottom first in thetrim opening and position in thebracket (3), • secure the retention clip on theupper part of the jack (2), and ...

• Ensure that the hold-strap contains the jack and tools before snappingthe buckle. • Ensure that the jack and tools are oriented as illustrated. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. If you are stowi...

7. Repeat this tightness check procedure (every six months, per scheduled maintenance information), when servicing the spare tire pressure or at any time that the spare tire is disturbed through service ofother components. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified t...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32–A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

• Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). • If a ring forms o...

quality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement the styleand appearance of your vehicle. Each product is made from high qualitymaterials that meet or exceed rigid specifications. For best results, usethe following products or...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informat...

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OP...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil filler cap 9. Engin...

3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoi...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause s...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. Turn the bladeat a right angle to the arm. Push thelock tab (A) to release the bladefrom the arm loop and pull theblade down toward the windshieldto remove it from the arm. 2. Attach the new blade to the armloop and pull i...

5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within the MIN and MAX marks or the lower andupper holes, the oil level is acce...

• 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above the MAXmark or upper hole may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter. Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, ...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

5. Re-start the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to anauthorized dealer as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer. Refe...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. Re...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding one gallon of fuel is enough ...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the range between the MIN and MAX lines. Besure to put the cap back ...

Checking and adding manual transmission fluid (if equipped) 1. Park the vehicle on a levelsurface. 2. Engage the parking brake fully –put in first gear. 3. Ensure the vehicle cannot move. 4. Clean the filler plug. 5. Remove the filler plug andinspect the fluid level. 6. Fluid level should be at bott...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................57 Air cleaner filter ...............272, 274 Airbag supplemental restraintsystem ................111–112, 120, 123 and child safety seats ............113description ..............112, 120, 123disposal ....................................126driver airbag ....