Ford 2007 Crown Victoria v.3- Manuals

Notice to owners of Severe Duty vehicles Before you drive your vehicle, be sure to read the Severe Duty Owner’s Guide supplement. This book contains important operation and maintenance information. Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontro...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapter for more information). O/D off: Illuminates when the overdrive function of thetransmission has been turned OFF,refer to the Driving chapter. If the light does not illuminat...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM stereo (if equipped) 1. Seek: Press / to find the next strong station down/up thefrequency band. 2. Tune: Press / to manually change radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: To set a station: Select frequency ban...

When activated, AUTOSET will momentarily appear in the display whenany of the preset controls are pressed. Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.Recommended level is 1–3. Level 0 turns the feature off and leve...

Dolby: Works in tape mode to reduces tape noise and hiss. Press MENU until DOLBY XX appears in the display. Press SEL-TEXT to toggle ON/OFF.The Dolby 威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby 威 and the double-D symbol are registered t...

9. MENU: Press MENU repeatedly to access RDS on/off.Use SEL-TEXT to toggle RDS on/off. Press MENU again to access Program type mode or ShowType mode. (MENU must be pressed within 10 seconds to proceed tothe next RDS mode.) The Federal Communications Commission (FCC) and the Canadian Radioand Telecom...

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circul...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the...

To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ve...

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control....

5. At the desired autolamp time delay, place the headlamp switch in theOFF position. • At this point, the exterior lamps turn off and the time delay is set. High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slight...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate the thumbwheel from leftto right to brighten theinstrument panel. • Rotate the thumbwheel from rightto left to dim the instrumentpanel. Domelamp Control The panel dimmer control a...

INTERIOR LAMPS Map/Courtesy lamps The courtesy lamps light when: • any door is opened. • the instrument panel dimmerswitch is rotated past the detent. • the UNLOCK control of theremote entry controls is pressedand the ignition is OFF. The reading lamps can be turned onby pressing the rocker controls...

Rear courtesy/reading lamps Rotate the lens to illuminate thelamp. With the lens in the flatposition, the courtesy lamp lightswhen: • Any door is opened. • The panel dimmer thumbwheel isrotated fully to the right pastdetent. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize...

Function Trade Number Rear reading lamp 578 Map lamp 906 Dual floorwell lamp 906 Glove compartment 168 Visor vanity lamp - Slide on Rail system(SOR) 37 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer. Replacing the inte...

1. Make sure headlamp switch is inOFF position, then open the trunkand remove the pin-type retainerand carefully pull the carpet away toexpose the lamp assembly hardware. 2. Remove three nuts and the lampassembly from the vehicle. 3. Remove the bulb socket byrotating it counterclockwise, thenpulling...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. Never adjust the steer...

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment • Power point (inside storage bin) • Cupholders • Air vents to the rear seating positions (heat only) Use only soft cups in the cupholder. Hard objects can injure youin a...

Programming Do not program the HomeLink 威 with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of theHomeLink 威 . It is also recommended that a new battery be placed in the hand-held...

If the indicator light(s) underneath the house icon blink rapidly for twoseconds and then turn to a continuous light, proceed with steps 6through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “...

Reprogramming a single HomeLink 姞 button To program a device to HomeLink 威 using a HomeLink 威 button previously trained, follow these steps: 1. Press and hold the desiredHomeLink 威 button. DO NOT release the button. The display willread CHANNEL “X” (1,2 or 3)TRANSMIT 2. The display will change toCHA...

To prevent the battery from being discharged, do not use the powerpoint longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocke...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place. Heated outside mirrors (if equipped) Both mir...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control toadjust accelerator and brake pedal. • Press the right side of the control to adjust the...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This willnot erase your vehicle’spreviously set speed. • Press the speed control OFFcontrol. Note: When you turn the speed control or the ignition off, yourspeed control set speed memory iserased. ...

Climate control features • Press TEMP + or - to adjusttemperature. MOON ROOF (IF EQUIPPED) Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves. When closing the moon roof, you should verify that it is free ofobstructions and ensu...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-heldtransmitters with a single built-in device. This feature will learn the radiofrequency codes of most transmitters to ope...

6. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink 威 button. Repeat the press/hold/rele...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status. Thesystem will al...

Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km. If you calculate your average fueleconomy by dividing gallons of fuelused by 100 miles traveled(kilometers traveled by liters used),your figure may be different than...

LOW FUEL. Displayed as an early reminder of a low fuel condition. Warning message can be reset by pressing the RESET button, but willreturn after 10 minutes. If any other button is pressed besides RESET,the message ’’PRESS RESET TO CLEAR’’ will appear in the MessageCenter. Once this message disappea...

2. Press and hold the RESETcontrol for 3 seconds and release.Oil life is set to 100% and “OIL LIFESTART VALUE SET TO XXX%” isdisplayed. POSITIVE RETENTION FLOOR MAT Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator or the brake ...

KEYS The vehicle is equipped with a master (black) key and valet (gray) keylock system (if equipped with valet feature). • The master key will access the vehicle’s doors, trunk, glove box,ignition and remote trunk release. • The valet key (if equipped) will access doors and ignition only. Before usi...

The vehicle may still be locked with the key in the ignition, andperforming one of the following actions: • Pressing the manual lock button on the door. • Operating the remote entry transmitter (if equipped). • Operating the keyless entry keypad (if equipped). • Operating the driver’s door with a ke...

Keep vehicle doors andluggage compartment locked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves in the trunk and riskinjury. Children should be taughtnot to play in vehicles. On hot days, the temperature in the trunk or vehicle interior canrise...

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after thelast door is closed, or after 10 minutes if the last door is left open. Radio type approval numbers for remote ent...

Erasing personal code To erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 2. Press and release 1 • 2 within 5 seconds of step 1. 3. Press and hold 1 • 2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure. Unlocking the ...

Immobiliser System PATS XCVR certification numbers Tunisia 269/MAT/2004 United Arabian Emirates 5/10-2/3274/3774 Uruguay 025/FR/2003 USA NT8-15607PAT3XCVR Zambia CAZ/ENG/CA/2005/02/8 Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authorit...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position. The theft indicator on theinstrument panel will flash everytwo seconds when the vehicle isarmed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the v...

1. Insert the first previouslyprogrammed coded key into the ignition and turn the ignition from 1(OFF/LOCK) to the 3 (ON) position(maintain ignition in 3 (ON) for atleast one second). 2. Turn ignition to 1 (OFF/LOCK)and remove the first coded key from the ignition. 3. Within ten seconds of removingt...

The system is ready to arm whenever the key is out of the ignition. Anyof the following actions will arm the alarm system: • Press the remote transmitter lock control one time to arm the system. • Lock all doors using the keypad. • Lock all doors using the interior power lock switch while the driver...

SEATING Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision.To properly adjust your head restraints, lift the head restraint so that itis located directly behind your head or as close to that position aspossible. Refer to the following to raise and l...

Press to move the front portion ofthe seat cushion up or down. Press to move the rear portion ofthe seat cushion up or down. Using the power lumbar support (if equipped) The power lumbar control is locatedon the outboard side of the seat. Press one side of the control toadjust firmness. Press the ot...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, even intermittently, have the PersonalSafety System 娂 serviced at an authorized dealer immediately. Unless serviced, the system may not fu...

Lap belts Adjusting the front center seat lap belt (if equipped) The lap belt should fit snugly and as low as possible around thehips, not across the waist. The lap belt does not adjustautomatically. Insert the tongue intothe correct buckle (the buckleclosest to the direction the tongue iscoming fro...

Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and preventsmore belt from being pulled out if the belt is pulled out too quickly. Thebelt will unlock when you stop pulling on it. Automatic locking mode In this mode, the shoulder belt is pre-locked. The belt wi...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Front safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver and frontoutboard passenger. Adjust theheight of the shoulder belt so thebelt rests across the middle of yourshoulder. To lower the shoulder belt height,push the button and slide the heightadjuster down...

One time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the Belt-Minder 威 is disabled for the current ignition cycle. The Belt-Minder 威 feature will enable during the same ignition cycle if the occupant buckles and remains b...

3. For the seating position being disabled, at a moderate speed, bucklethen unbuckle the safety belt 9 times, ending in the unbuckled state.(Step 3 must be completed within 50 seconds after the safety beltwarning light turns off.) • After Step 3, the restraint system warning light (airbag light) wil...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module. Placingobjects on or over the ai...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

The diagnostic module monitors its own internal circuits as well as thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power and the airbag ignitors. Several air bag system components get hot after in...

For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay li...

Objects Pass Airbag OffIndicator Lamp PassengerAirbag Small (i.e. 3 ring binder,small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase,fully packed luggage) Lit Disabled Empty seat, or small tomedium object with safetybelt buckled Lit Disabled If you think that the status of the pas...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is ...

to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldeceleration. Several air bag system components get hot after inflation. Do nottouch them after inflation. If the side airbag hasdeployed, the airbag wil...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by l...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with LATCH andtether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, otherwise routethe tether strap over the top of the seatback. 3. Locate the correct anchor for the...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Highway hazards No matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly to theclosest safe area out of traffic. This may further damage the flat tire, butyour safety is more important. If you feel a sudden vibration or rid...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label, which is located on the B-Pillar or the edge of thedriver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction and Tempe...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use chains, it i...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cross thechains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agen...

• Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance information for more information. Tr...

• do not allow waves to break higher than 6 inches (15 cm) above thebottom edge of the rear bumper. Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant an...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks thegearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsillumi...

5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (ST...

Do not use starting fluid such as ether in the air intake system. Suchfluid could cause immediate explosive damage to the engine and possiblepersonal injury. If you should experience cold weather starting problems on E 85 ethanol, and neither an alternative brand of E 85 ethanol nor an engine block ...

ENGINE BLOCK HEATER (IF EQUIPPED) To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater) adapters. Use of an engine block heater is strongly recommended if you live in aregion where temperatures reach -10°F (-23°C) or below. For best...

Anti-lock brake system (ABS) This vehicle is equipped with an anti-lock braking system (ABS). A noisefrom the hydraulic pump motor and pulsation in the pedal may beobserved during ABS braking events. Pedal pulsation coupled with noisewhile braking under panic conditions or on loose gravel, bumps, we...

If the parking brake fails to releaseafter completing this procedure, usethe manual parking brake releaselever. Pull the lever to manually releasethe parking brake. TRACTION CONTROL 姟 (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control 娂 system. This system helps you mainta...

During Traction Control 娂 operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not“rev-up” when you push further on the accelerator. This is normalsystem behavior. If you should become stuck in snowor ice or on a very slippery roadsurface, try...

It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level(below the MIN mark on the reservoir). • Some noise is normal during operation. If the noise is excessive, checkfor low po...

This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch islocated on the left side of the trunk.If this switch is in the OFF ...

2. Locate the access plug on theunderside of the steering columncover. 3. Remove the access plug using a flat head screwdriver. Insert thescrewdriver into the access hole nearest the steering wheel. Then pushand hold the override button using a flat head screwdriver. Apply thebrake pedal and shift t...

2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral) . When the key is in the ignition and in the ACC position, theautomatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. To avoid unwantedvehicle movement, always s...

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in...

• The hazard lights control islocated on top of the steeringcolumn. • Depress hazard lights control toactivate all hazard flasherssimultaneously. • Depress control again to turn theflashers off. FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the elect...

3. If no fuel leak is apparent, reset the fuel pump shut-off switch bypushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds andreturn the key to the OFF position. 5. Make a further check for leaks in the fuel system. FUSES AND RELAYS Fuses If electrical com...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 50A — — Red Red Red 60A — — Blue Yellow Yellow 70A — — Tan — Brown 80A — — Natural Black Black Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A Ignition (START) - Starter relaycoil, DTRS 2 7.5A Power mirrors, Door lockswitches, Mirror switch, Keypadswitch, Decklid switch, DDM,Cluster 3 5A Ignition (START) - Audio mute,Police PDB (Police vehicles only) 4 1...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 13 10A Ignition (ON) - Anti-lock BrakeSystem (ABS) module, Rear AirSuspension Module (RASM),Variable Assist Power Steering(VAPS), Cluster 14 15A Taxi, Adjustable pedals 15 10A Ignition (ON) - EATC module,A/C mode switch...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 24 10A Ignition (ON/START) - PassiveAnti-Theft System (PATS)module, Powertrain ControlModule (PCM) relay coil, Fuelrelay coil, Ignition coil relay coil 25 15A LCM (Park lamps, license lamps) 26 10A Ignition (ON/START) -...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For v...

5. Locate pry off notch (ifequipped) and remove the centerornament from the aluminum wheelwith the tapered end of the wheelnut wrench that came with yourvehicle. Insert and twist the handle,then pry against the wheel. 6. If equipped with a fullwheelcover, remove the wheelcovercenter ornament then lo...

To lessen risk of personalinjury, do not put any part of your body under the vehiclewhile changing a tire. Do not startthe engine when your vehicle ison the jack. The jack is ONLYmeant for changing the tire. • Never use the rear differentialas a jacking point. 8. Remove the metal lug nuts with the l...

3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other movingparts. 4. Check all battery terminals and remove any excessive corrosion beforeyou attach th...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not ...

cotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner(ZC-38-A) on the instrument panel and interior trim areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instrument panel. The dull finish in this area helps protect thedriver from undesirable windshi...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemica...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front of the hood. 3. Lift the hood until the liftcylinders hold it open. 2007 Crown Victoria (cro) Owners ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Windshield washer fluid reservoir 4. Air filter assembly 5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Power distribution box 9. Engine oil filler cap...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not ...

To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed. Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetro...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium GoldEngine Coolant since a Ford-approved recycling process is not yetavailable. Used engine coolant should be disposed of in an appropriate manner. ...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cool...

1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to an authorized dealer. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap whi...

Automotive fuels can cause serious injury or death if misused ormishandled. Fuel ethanol and gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforerefueling your vehicl...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the in...

5. Turn the filler cap clockwise 1/4 of a turn until it clicks at least once. If the Check Fuel Cap indicator or message comes on and stays on afteryou start the engine, the fuel filler cap may not be properly installed.Turn off the engine, remove the fuel filler cap, align the cap properly andreins...

The use of leaded fuel is prohibited by law and could damage yourvehicle. Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Studies indicate thatthese additives can cause your vehicle’s emission control system todeteriorate more ...

performance and emission control system protection for your vehicle.Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask your fuel supplier about gasolines that meet theWorld-Wide Fuel Charter. Do not add aftermarket fuel additive products to your fuel tank. Itshould not...

• The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you,...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

POWER STEERING FLUID Check the power steering fluid.Refer to scheduled maintenance information for the service interval schedules. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” linethat do not trigger the brake systemwarning lamp are within the normaloperating range, there is no need toadd fluid. If the fluid levels are outside of...

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage. If necessary, add fluid in 1/2 pint (250 ml) increments through the fillertube until the level is correct. If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill cond...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A ABS (see Brakes) .....................172 Air cleaner filter ...............253–254 Air conditioning ..........................35 Air suspension ...........................176 description ..............................176 Airbag supplemental restraintsystem ........................117–118, 127 and...

wrecker ....................................206 Traction control ........................174 Traction-lok rear axle ...............177 Transmission .............................177 brake-shift interlock(BSI) ................................177–178fluid, checking and adding(automatic) ..................