Ford 2007 Crown Victoria - Manuals

Notice to owners of Severe Duty vehicles Before you drive your vehicle, be sure to read the Severe Duty Owner’s Guide supplement. This book contains important operation and maintenance information. Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontro...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

Engine oil pressure: Illuminates when the oil pressure falls below thenormal range. Check the oil leveland add oil if needed. Refer to Engine oil in the Maintenance and Specifications chapter. Engine coolant temperature (ifequipped): Illuminates when the engine coolant temperature is high.Stop the v...

Speed control (if equipped): Illuminates when the speed controlis activated. Turns off when thespeed control system is deactivated. Door ajar (if equipped): Illuminates when one of the doors isnot completely shut and the ignitionis turned to ON. With the ignition inRUN position, a tone will sound fo...

Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as saf...

AUDIO SYSTEMS AM/FM stereo (if equipped) 1. Seek: Press / to find the next strong station down/up thefrequency band. 2. Tune: Press / to manually change radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: To set a station: Select frequency ban...

When activated, AUTOSET will momentarily appear in the display whenany of the preset controls are pressed. Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.Recommended level is 1–3. Level 0 turns the feature off and leve...

The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission (CRTC) recommend that FM radiobroadcasters use RDS technology to transmit information. FM radiostations are independently operated and individually elect to use RDStechnology to transmit station ID an...

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.Recommended level is 1–3. Level 0 turns the feature off and level 7 isthe maximum setting. Press MENU repeatedly to access and use SEL/TEXT to adjust the volume setting. T...

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circul...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the...

To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ve...

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control....

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of your headlampsshould be checked by your authorized dealer. TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the r...

Overhead console lamps To remove and replace the lamps in the overhead console: 1. Make sure the headlamp switch isin the OFF position and remove theoverhead console from the headlinerby pulling it straight down. 2. Remove the bulb socket from theback of the lamp housing by pullingit straight out. 3...

6. Without turning, remove the oldbulb from the lamp assembly bygently pulling it straight back out ofthe lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from...

5. Disconnect the electricalconnector from the bulb by pullingrearward. 6. Rotate the bulb socketcounterclockwise and remove fromlamp assembly. 7. Carefully pull bulb straight out ofthe socket and push in the new bulbuntil it snaps, locking it intoposition. 8. To complete installation, follow the re...

Replacing high-mount brakelamp bulbs 1. Remove two screws from thelamp assembly. 2. Carefully lift the lamp assemblyup for access to the bulbs. 3. Carefully pull the bulb socket outof the lamp assembly. 4. Pull the bulb straight out of thesocket and push in the new bulb. To install, reverse the remo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. Never adjust the steer...

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment • Power point (inside storage bin) • Cupholders • Air vents to the rear seating positions (heat only) Use only soft cups in the cupholder. Hard objects can injure youin a...

Programming Do not program the HomeLink 威 with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of theHomeLink 威 . It is also recommended that a new battery be placed in the hand-held...

If the indicator light(s) underneath the house icon blink rapidly for twoseconds and then turn to a continuous light, proceed with steps 6through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “...

Reprogramming a single HomeLink 姞 button To program a device to HomeLink 威 using a HomeLink 威 button previously trained, follow these steps: 1. Press and hold the desiredHomeLink 威 button. DO NOT release the button. The display willread CHANNEL “X” (1,2 or 3)TRANSMIT 2. The display will change toCHA...

Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocket. Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter ...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the leftside of the control. Press the rightside to restore the window controls. AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicl...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could causedamage to the glass ...

Do not use the speed control in heavy traffic or on roads thatare winding, slippery or unpaved. Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press th...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This willnot erase your vehicle’spreviously set speed. • Press the speed control OFFcontrol. Note: When ...

Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous light, proceed with Steps 6 through 8 to completeprogramming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usual...

• Proceed with Step 4 in the “Programming” section. Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office ...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status. Thesystem will al...

Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/100km. If you calculate your average fueleconomy by dividing gallons of fuelused by 100 miles traveled(kilometers traveled by liters used),your figure may be different than...

LOW FUEL. Displayed as an early reminder of a low fuel condition. Warning message can be reset by pressing the RESET button, but willreturn after 10 minutes. If any other button is pressed besides RESET,the message ’’PRESS RESET TO CLEAR’’ will appear in the MessageCenter. Once this message disappea...

2. Press and hold the RESETcontrol for 3 seconds and release.Oil life is set to 100% and “OIL LIFESTART VALUE SET TO XXX%” isdisplayed. POSITIVE RETENTION FLOOR MAT Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator or the brake ...

KEYS The vehicle is equipped with a master (black) key and valet (gray) keylock system (if equipped with valet feature). • The master key will access the vehicle’s doors, trunk, glove box,ignition and remote trunk release. • The valet key (if equipped) will access doors and ignition only. Before usi...

Deactivating/activating the autolock or auto-unlock feature Automatic door locks can also be turned on/off through the followingprocedure: You must complete Steps 1-7 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be repeated, you mustwait at least 30 seconds. ...

Keep vehicle doors andluggage compartment locked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves in the trunk and riskinjury. Children should be taughtnot to play in vehicles. On hot days, the temperature in the trunk or vehicle interior canrise...

The battery saver will shut off the interior lamps 30 minutes after thelast door is closed, or after 10 minutes if the last door is left open. Radio type approval numbers for remote entry receiver If the type approval of your remote entry system is inspected in one ofthe countries listed in the foll...

2. Within five seconds press 1 • 2 on the keypad to enter the programming mode. 3. Enter your personal 5-digit code. Each number must be enteredwithin five seconds of each other. 4. Press 1 • 2 to store the first personal code. 5. The doors will lock then unlock to confirm programming of the newcode...

2. Press and release 1 • 2 within 5 seconds of step 1. 3. Press and hold 1 • 2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure. Unlocking the doors and releasing the trunk with the keyless entrysystem To unlock the driver door, enter either the factory-set code...

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. Your vehicle comes with two coded keys (or three, if your vehicle is equipped with the valet feature); additional coded keys may bepurchased from your autho...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position. The theft indicator on theinstrument panel will flash everytwo seconds when the vehicle isarmed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the v...

SEATING Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision.To properly adjust your head restraints, lift the head restraint so that itis located directly behind your head or as close to that position aspossible. Refer to the following to raise and l...

Press to move the front portion ofthe seat cushion up or down. Press to move the rear portion ofthe seat cushion up or down. Using the power lumbar support (if equipped) The power lumbar control is locatedon the outboard side of the seat. Press one side of the control toadjust firmness. Press the ot...

To operate the heated seats: • Push the indicated side of thecontrol for maximum heat. • Push again to deactivate. • Push the indicated side of thecontrol for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While theignition is in the ON position,...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

The front passenger sensing system can automatically turn off the frontpassenger airbag and passenger seat-mounted side airbag. The system isdesigned to help protect small (child size) occupants from frontal airbagdeployments when they are seated or restrained in the front passengerseat contrary to ...

Determining if the Personal Safety System 姟 is operational The Personal Safety System 娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Referto the Warning light section in the Instrument cluster chapter. Routine maintenance of the Personal S...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. Energy management feature • This vehicle has a safety belt system with an energy managementfeature at the front outboard seating positions to help further reducethe risk of injury in the event of a head-on collision. • This...

Shorten and fasten the belt whennot in use. The front outboard and rear safetyrestraints in the vehicle arecombination lap and shoulder belts.The front outboard passenger andrear seat safety belts have threetypes of locking modes described asfollows: Vehicle sensitive mode This is the normal retract...

How to use the automatic locking mode • Buckle the combination lap andshoulder belt. • Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automa...

How to disengage the automatic locking mode Ford Motor Company recommends that all passenger safety beltassemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify that the ⬙ automatic locking retractor ⬙ feature for child seats is still working proper...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Safety belt maintenance Inspect the safety belt systems period...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of th...

Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries. Ford Motor Company recommends that an authorized dealerinspect all steering column assemblies in use in vehicles involved in a collision. Failure to inspect and if necessary repl...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

The diagnostic module monitors its own internal circuits as well as thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power and the airbag ignitors. Several air bag system components get hot after in...

• a front passenger takes his/her weight off of the seat for a period oftime, For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing systemuses a ⬙ passenger a...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is ...

to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldeceleration. Several air bag system components get hot after inflation. Do nottouch them after inflation. If the side airbag hasdeployed, the airbag wil...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by l...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with LATCH andtether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

This begins with the letters “DOT” and indicates that the tire meets allfederal standards. The next two numbers or letters are the plant codedesignating where it was manufactured, the next two are the tire sizecode and the last four numbers represent the week and year the tire wasbuilt. For example,...

4. Use both eye and ear protection.For a mounting pressure more than 20 psi greater than the maximumpressure, a Ford Dealer or other tire service professional should do themounting.Always inflate steel carcass tires with a remote air fill with the personinflating standing at a minimum of 12 ft. away...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on the Saf...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Follow these guidelines when us...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or changedunless a leak is suspected or repair required. RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination ...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks thegearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsillumi...

5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (ST...

Do not use starting fluid such as ether in the air intake system. Suchfluid could cause immediate explosive damage to the engine and possiblepersonal injury.If you should experience cold weather starting problems on E 85 ethanol, and neither an alternative brand of E 85 ethanol nor an engine block h...

BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance information for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional...

The ABS operates by detecting theonset of wheel lockup during brakeapplications and compensates forthis tendency. The wheels areprevented from locking even whenthe brakes are firmly applied. Theaccompanying illustration depictsthe advantage of an ABS equippedvehicle (on bottom) to a non-ABSequipped ...

If the parking brake fails to releaseafter completing this procedure, usethe manual parking brake releaselever. Pull the lever to manually releasethe parking brake. TRACTION CONTROL 姟 (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control 娂 system. This system helps you mainta...

During Traction Control 娂 operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not“rev-up” when you push further on the accelerator. This is normalsystem behavior. If you should become stuck in snowor ice or on a very slippery roadsurface, try...

It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level(below the MIN mark on the reservoir). • Some noise is normal during operation. If the noise is excessive, checkfor low po...

This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch islocated on the left side of the trunk.If this switch is in the OFF ...

2. Locate the access plug on theunderside of the steering columncover. 3. Remove the access plug using a flat head screwdriver. Insert thescrewdriver into the access hole nearest the steering wheel. Then pushand hold the override button using a flat head screwdriver. Apply thebrake pedal and shift t...

2. Insert the key and turn it to ACC. Apply the brake pedal and shift to N (Neutral) . When the key is in the ignition and in the ACC position, theautomatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. To avoid unwantedvehicle movement, always s...

• Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. I...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

• The hazard lights control islocated on top of the steeringcolumn. • Depress hazard lights control toactivate all hazard flasherssimultaneously. • Depress control again to turn theflashers off. FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the elect...

3. If no fuel leak is apparent, reset the fuel pump shut-off switch bypushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds andreturn the key to the OFF position. 5. Make a further check for leaks in the fuel system. FUSES AND RELAYS Fuses If electrical com...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 50A — — Red Red Red 60A — — Blue — Yellow 70A — — Tan — Brown 80A — — Natural — Black Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake ped...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A Ignition (START) - Starter relaycoil, DTRS 2 7.5A Power mirrors, Door lockswitches, Mirror switch, Keypadswitch, Decklid switch, DDM,Cluster 3 5A Ignition (START) - Audio mute,Police PDB (Police vehicles only) 4 1...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 13 10A Ignition (ON) - Anti-lock BrakeSystem (ABS) module, Rear AirSuspension Module (RASM),Variable Assist Power Steering(VAPS), Cluster 14 15A Taxi, Adjustable pedals 15 10A Ignition (ON) - EATC module,A/C mode switch...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 24 10A Ignition (ON/START) - PassiveAnti-Theft System (PATS)module, Powertrain ControlModule (PCM) relay coil, Fuelrelay coil, Ignition coil relay coil 25 15A LCM (Park lamps, license lamps) 26 10A Ignition (ON/START) -...

Tire change procedure To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of thevehicle) to the tire being changed. If the vehicle slips off the jack, you or someone...

JACK LOCATION The jack location markings can befound on the lower outer edge of the body. • Locate the jack locator mark (B)on the body (C) near the tire youare changing, then place the jack(D) under the frame (A) of the vehicle aligning it with the mark (B). • Position the jack according to thefoll...

11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nuttorque specification. 12. For full size spare aluminumwheel, firmly install the centerornament. If equipped with a fullsize spare tire/wheel a...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionv...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as g...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellan...

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoi...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLe...

SERVICE RECOMMENDATIONS To help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informati...

5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Power distribution box 9. Engine oil filler cap 10. Automatic transmission fluid dipstick WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely....

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. Turn the bladeat a right angle to the arm. Push thelock tab (A) to release the bladefrom the arm loop and pull theblade down toward the windshieldto remove it from the arm. 2. Attach the new blade to the armloop and pull i...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instruction...

Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andAp...

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with a solution of baking soda and water. It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store ...

4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Release the parking brake. With your foot on the brake pedal and withthe A/C on, put the vehicle in D (Drive) and allow the engine to idle forat least one minute. 7. Drive...

Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -34°F ...

Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specifiedfunction and vehicle location. Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to...

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the enginecoolant. For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when the eng...

Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium Gold...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

If you do not use the proper fuel filler cap, excessive vacuum inthe fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. Automotive fuels can cause serious injury or death if misused ormishandled. Fuel ethanol and gaso...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...

Unleaded Gasoline engines If you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of “Regular” unleadedgasoline. “Premium” unleaded gasoline is not recommended because itmay cause these problems to become more pronounced. If the prob...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a...

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of MPG (L/100 km)expected on the vehicle under optimum conditions. Your fuel economymay vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is...

POWER STEERING FLUID Check the power steering fluid.Refer to scheduled maintenance information for the service interval schedules. If adding fluid is necessary, use only MERCON 威 ATF . 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gau...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” linethat do not trigger the brake systemwarning lamp are within the normaloperating range, there is no need toadd fluid. If the fluid levels are outside of...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick. Refer to Maintenance product specifications and capacities in this chapter. Use of a non-approved automatic transmission fluid may c...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Mobile-ease 娂 hands-free communication system Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to y...

A ABS (see Brakes) .....................168 Air cleaner filter ...............248–249 Air conditioning ..........................34 Air suspension ...........................173 description ..............................173 Airbag supplemental restraintsystem ................................116, 125...

Traction-lok rear axle ...............174 Transmission .............................174 brake-shift interlock(BSI) ................................174–175fluid, checking and adding(automatic) .............................246fluid, refill capacities ..............251lubricant specifications ............